If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
power supply on new build w old power supply
I am trying to build a computer for a friend on the cheap using recycled and
rebate parts. I have a new winfast motherboard (939) and an antec power supply with the older connector that has four less connectors. Can this power supply be used with this motherboard. |
#2
|
|||
|
|||
power supply on new build w old power supply
ed jurewicz wrote:
I am trying to build a computer for a friend on the cheap using recycled and rebate parts. I have a new winfast motherboard (939) and an antec power supply with the older connector that has four less connectors. Can this power supply be used with this motherboard. Yes, a 20 pin power supply, can be used to power a 24 pin motherboard. The purpose of the extra four pins, is to provide room for more 3.3V, 5V, and 12V current to flow. The critical one there, is the 12V pin, and the 3.3V and 5V are relatively unimportant on a modern motherboard (because the power consumption is not as high as, say, on a dual socket Athlon MP machine - some of those used to burn their power connectors). With the 20 pin power connector, you have one 12V pin available. It has room for up to 6 amps of current flow, before the pin gets too hot. The 12V pin powers the motherboard fan headers (say 0.5A for several fans). It also powers the PCI Express video slots, and that is the determining factor. Some video cards, draw up to 4 amps from their video card slot. A 20 pin connector can power one video card. But if your motherboard was an SLI motherboard, and had two PCI Express x16 video card slots, and you used two of those 4 amp video cards, that would be 8+ amps of load. So what I tell people, is the 20 pin is safe, as long as you only have one video card. There are power measurements on Xbitlabs.com , for various video cards, and cards that have a PCI Express 2x3 on the end of the card, sometimes don't draw quite as much +12V from the video slot. So it is possible to drive two video cards, with a 20 pin power supply, because the one wire/pin would be sufficient. Of course, the 20 pin supply won't have the necessary PCI Express 2x3 power connectors to begin with, so at that point you'd probably buy a decent ATX supply to replace it. The 24 pin connector has a total of two 12V pins, leaving room for up to 12 amps of current to flow. That should be good enough for two 4 amp video cards plus the fan headers. Pin 1 of the 20 pin, goes to pin 1 on the 24 pin connector. The nylon shell of the connectors, helps ensure that you mate them correctly. (The shell has shapes to prevent mis-mating.) You may find, depending on the shape of the latch, that the latch won't engage fully (which sucks). Latching the connectors together, prevents thermal migration of the connector out of the socket. The above rules don't take all possible hardware configurations into account. I presume it is possible for PCI Express x1 cards to draw power too. I don't know if they'd be drawing down on the 12V rail, as for a lot of peripheral type functions, the 3.3V supply which is also on the slot connector, is a better fit for the application. (A GbE Ethernet card might only need 3.3V or lower operating voltages, for example.) So at least for the current time, and until a counter example is provided, I'd use the video card count as the acid test of safely. One video card should be OK with the 20 pin. HTH, Paul |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
power supply for a 680i build | Neuromancer | Homebuilt PC's | 0 | February 23rd 07 09:16 PM |
Any LOW power desktops with external wall wart power supply? | [email protected] | Homebuilt PC's | 14 | June 2nd 06 02:29 AM |
Antec TPII 550EPS12V or Cooler Master Real Power 550 power supply??? | brian | Homebuilt PC's | 7 | May 6th 05 07:56 AM |
Antec TPII 550EPS12V or Cooler Master Real Power 550 power supply??? | brian | Overclocking | 6 | May 5th 05 12:21 PM |
chassis power switch problem or fuse in power supply? | Conor | Homebuilt PC's | 1 | July 16th 03 01:14 AM |