|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
April 18th 04, 11:48 AM
|
|||
|
|||
Getting network to work with Zonealarm
Can only get my home network to work if I turn off my zonealarm firewall.
Have only two pc`s connected by ethernet cable, any suggestions please? 
|
|
#2
April 18th 04, 12:48 PM
|
|||
|
|||
|
anthony fidler wrote:
Can only get my home network to work if I turn off my zonealarm firewall. Have only two pc`s connected by ethernet cable, any suggestions please? go into the "firewall" tab on the left, then the "zones" tab on the top, and then add the computers to each other's safe lists using the buttons at the bottom. -- spammage trappage: replace fishies_ with yahoo
|
|
#3
April 19th 04, 07:37 PM
|
|||
|
|||
|
"anthony fidler" wrote in message news:%0tgc.436$Gq3.31@newsfe1-win... Can only get my home network to work if I turn off my zonealarm firewall. Have only two pc`s connected by ethernet cable, any suggestions please? You need to set the zones for it to work. Under firewall you have 2 tabs Main and Zone, there should be an entry for your internet connection and one that shows your network cards ip address. Set the network card to trusted and you should then be able to access each pc's shared folders Mark
|
|
#4
April 20th 04, 11:52 PM
|
|||
|
|||
|
"mark" wrote in message news:41Vgc.184$C24.165@newsfe1-win... "anthony fidler" wrote in message news:%0tgc.436$Gq3.31@newsfe1-win... Can only get my home network to work if I turn off my zonealarm firewall. Have only two pc`s connected by ethernet cable, any suggestions please? You need to set the zones for it to work. Under firewall you have 2 tabs Main and Zone, there should be an entry for your internet connection and one that shows your network cards ip address. Set the network card to trusted and you should then be able to access each pc's shared folders Mark You also need to have the paid for version of Zonealarm, the free donwloadable version doesn`t support networking. I tried. IIRC theres some info on this on the zonealarm website. Pete
|
|
#5
April 21st 04, 04:48 AM
|
|||
|
|||
|
"Pete" wrote in message
... "mark" wrote in message news:41Vgc.184$C24.165@newsfe1-win... "anthony fidler" wrote in message news:%0tgc.436$Gq3.31@newsfe1-win... Can only get my home network to work if I turn off my zonealarm firewall. Have only two pc`s connected by ethernet cable, any suggestions please? You need to set the zones for it to work. Under firewall you have 2 tabs Main and Zone, there should be an entry for your internet connection and one that shows your network cards ip address. Set the network card to trusted and you should then be able to access each pc's shared folders Mark You also need to have the paid for version of Zonealarm, the free donwloadable version doesn`t support networking. I tried. IIRC theres some info on this on the zonealarm website. Pete Not so. The free version supports trusted zones.
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| A strange problem with my network. Need advice | E.D. | General | 4 | October 16th 04 03:28 PM |
| Last/Fastest cB0 stepped 'gray zone' Celerons work natively on Abit ZM6/BM6? | pgtr | General | 15 | July 9th 04 07:29 PM |
| DELL upgrade with Kingston Value RAM - will it work properly | stromer | General | 0 | January 31st 04 08:29 AM |
| Wireless Network Card On Win98 Not Working | Gary Brown | General | 2 | December 12th 03 11:32 AM |
| ZoneAlarm & home network | [email protected] | Homebuilt PC's | 5 | October 18th 03 10:18 AM |
Linear Mode
