A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » System Manufacturers & Vendors » Compaq Computers
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Unable to access Setup/BIOS



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #16  
Old September 5th 03, 04:37 PM
DEJ57
external usenet poster
 
Posts: n/a
Default

I have a few Compaq laptops that I'd love to see you pull this trick on.
Even a few Presario desktops that only supported one HD as shipped from
Compaq.


We weren't talking about laptops. Different animal, for the most part.

Both my 4112 and 7240 shipped with only a two connector data on the first
channal and the second channal. To add additional HDDs, I HAD TO USE STANDARD
DATA CABLES--no SCSI data cables were easily available retail in my area.
Could have special ordered them or had them made, I suppose, but for what
reason?

I would argue against describing these Presarios as only supporting one HDD as
shipped from Compaq (I have had a 386 and several 486 Compaq laptops that
support four IDE with a little bit of effort, and that Compaq will tell you
can't be done--"its not supported") Compaq was simply too cheap to supply
three connector data cables on both the channels, nor did they want the excess
cable stuffed into the boxes, I'd bet. On the systemboard of the 4112 they
were too cheap to include the sockets for additional RAM chips as well as the
socket for upgrade video memory. But the solder points and board space for
those sockets were there. But back to the HDDs--if you happened to have CS
three connector data cables, these Presarios would support four CS jumpered IDE
devices fine--and they would also support four IDE devices using standard three
connector data cables just as well, jumpered as Master and Slave,
appropriately. The systemboard didn't care.
The "support" was there, just not the necessary number of connectors on the
data cables. One just used the new three position data cable that comes with
most new HDDs. But the included cables have never been CS, in my experience.
Compaq 's going against the grain in using CS sure has been the source of much
confusion and many questions in support forums for Compaq.

Dale
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
PS2 Port gone, Please Help Access The Bios Jedinial bullfrogz Homebuilt PC's 3 September 17th 04 11:30 PM
No BIOS access, and can't boot normally even with new OS on HD ToolPackinMama Homebuilt PC's 9 April 12th 04 08:40 PM
REPOST: A7V333: no longer able to access hard disks at boot time Chris Metzler Asus Motherboards 6 January 8th 04 07:29 PM
Unable to create Direct3d device CW Overclocking AMD Processors 3 November 9th 03 06:09 PM
Unable to access CD-ROM Maxi Cdr 1 August 12th 03 03:24 PM


All times are GMT +1. The time now is 08:57 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.