If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Laserjet 4000N "Tray 1 Load Plain Letter" problem.
I recently had my Laserjet 4000N fixed ($200 to clear a paper jam).
Now everytime I try to print something I have an error "Tray 1 Load Plain Letter" and the orange attention light blinks. I wiggle and jiggle both the upper paper door and the bottom paper tray and eventually it starts printing. Once it prints, if I don't disturb the bottom tray, I'm okay for awhile. The problem wasn't there before the repair job. I caused the original paper jam by putting 10 sheets of paper in the upper paper slot. All ten sheets fed into the printer at once. Does anyone have a solution for this? I would rather try and fix it myself than to send it back to the shop. Thank you for your time and help; Frank |
#2
|
|||
|
|||
Could have saved you $200. The multi feeding on manual feed tray is most
likely caused by the separation pad worn out and just needed replacing. As for the latest problem. Check that the manual feed sensor is clicked into position. "Philadelphia Frank" wrote in message ... I recently had my Laserjet 4000N fixed ($200 to clear a paper jam). Now everytime I try to print something I have an error "Tray 1 Load Plain Letter" and the orange attention light blinks. I wiggle and jiggle both the upper paper door and the bottom paper tray and eventually it starts printing. Once it prints, if I don't disturb the bottom tray, I'm okay for awhile. The problem wasn't there before the repair job. I caused the original paper jam by putting 10 sheets of paper in the upper paper slot. All ten sheets fed into the printer at once. Does anyone have a solution for this? I would rather try and fix it myself than to send it back to the shop. Thank you for your time and help; Frank |
#3
|
|||
|
|||
Thank you for the timely and helpful reply.
I'll look for that sensor; I have a manual somewhere. Frank On Mon, 31 Jan 2005 18:15:35 +0000 (UTC), "Malvin" wrote: Could have saved you $200. The multi feeding on manual feed tray is most likely caused by the separation pad worn out and just needed replacing. As for the latest problem. Check that the manual feed sensor is clicked into position. "Philadelphia Frank" wrote in message .. . I recently had my Laserjet 4000N fixed ($200 to clear a paper jam). Now everytime I try to print something I have an error "Tray 1 Load Plain Letter" and the orange attention light blinks. I wiggle and jiggle both the upper paper door and the bottom paper tray and eventually it starts printing. Once it prints, if I don't disturb the bottom tray, I'm okay for awhile. The problem wasn't there before the repair job. I caused the original paper jam by putting 10 sheets of paper in the upper paper slot. All ten sheets fed into the printer at once. Does anyone have a solution for this? I would rather try and fix it myself than to send it back to the shop. Thank you for your time and help; Frank |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problem with Epson R300 printer - Disk tray seems balky | geezer | General | 3 | February 14th 05 03:01 AM |
Problem with LaserJet 4M...rollers? | Dan | Printers | 12 | January 15th 05 08:12 PM |
pc problems after g card upgrade + sp2 | ben reed | Homebuilt PC's | 9 | November 30th 04 02:04 AM |
HP LaserJet 1300 Manual Feed Problem | Darlene | Printers | 0 | September 13th 04 02:34 PM |
This problem has baffled everyone... | Nick G | General | 46 | May 22nd 04 04:01 AM |