If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Dual channel question
Got a quick question about dual channel config on a Soltek SL-75FRN2 board.
Currently running a Barton 2500 with 1 stick PC2700 512Mb Samsung DDR. I've got 2 x 256Mb sticks of matched PC3200 Samsung DDR that I'm going to put in the primary dual channel slot and one of the secondaries. I know this will enable dual channel; my other system has 2 x 512Mb set up this way. What happens if I put the remaining original 512Mb PC2700 stick in the last remaining slot. Does dual channel still function? Will it even boot? And if you must have matched RAM in all three, does dual channel still operate with all three slots filled? The m/b manual is none too clear on this. I'd appreciate an answer to all three of these questions if someone knows....thanks. |
#2
|
|||
|
|||
Hello
Well i have a Soltek SL-75FRN-RL board with 3x256mb ddr pc3200 ram and dual channel for me is still functioning so it should do for you. On Fri, 02 Jul 2004 02:39:13 GMT, "Augustus" wrote: :Got a quick question about dual channel config on a Soltek SL-75FRN2 board. :Currently running a Barton 2500 with 1 stick PC2700 512Mb Samsung DDR. I've :got 2 x 256Mb sticks of matched PC3200 Samsung DDR that I'm going to put in :the primary dual channel slot and one of the secondaries. I know this will :enable dual channel; my other system has 2 x 512Mb set up this way. What :happens if I put the remaining original 512Mb PC2700 stick in the last :remaining slot. Does dual channel still function? Will it even boot? And if :you must have matched RAM in all three, does dual channel still operate with :all three slots filled? The m/b manual is none too clear on this. I'd :appreciate an answer to all three of these questions if someone :knows....thanks. : ----- Lee. |
#3
|
|||
|
|||
On Fri, 02 Jul 2004 02:39:13 GMT, "Augustus"
wrote: Got a quick question about dual channel config on a Soltek SL-75FRN2 board. Currently running a Barton 2500 with 1 stick PC2700 512Mb Samsung DDR. I've got 2 x 256Mb sticks of matched PC3200 Samsung DDR that I'm going to put in the primary dual channel slot and one of the secondaries. I know this will enable dual channel; my other system has 2 x 512Mb set up this way. What happens if I put the remaining original 512Mb PC2700 stick in the last remaining slot. Does dual channel still function? Will it even boot? And if you must have matched RAM in all three, does dual channel still operate with all three slots filled? The m/b manual is none too clear on this. I'd appreciate an answer to all three of these questions if someone knows....thanks. If all three stix were PC3200 then the answer to your question [s] would be yes ! Because they are not I suspect that all three will run to the lowest common denominator - PC2700. You could ' suck it and see ' what happens. The standard setting of 11x200 would be too high for your PC2700 to cope with, but a starting underclock of 10x180 should allow a safe boot and give you a workable point to begin to find the ceiling of your mixed 27/3200 memory. You never know your 2700 may be good enough to live with the 3200, I would give it a go and see. Can't speak for the Soltec board but in the event of a lockup, booting with the insert key held down should give you access to the ' safe default ' settings in the BIOS. BoroLad N.B Pulling the BIOS jumper, whilst disconnected from the mains, will in the event of a catastrophic failure give you back your MOBO. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
dual channel memory | Buddy Mills | AMD x86-64 Processors | 2 | November 6th 04 02:37 AM |
MSI Master2-FAR and Dual 244's dual memory channel questions?!!? | Douglas Crane | AMD x86-64 Processors | 0 | August 27th 04 06:40 AM |
Dual channel DDR ? | Deadly_M | Overclocking | 18 | January 4th 04 03:25 PM |
Dual Channel Memory Question | CiRcUiT | Overclocking AMD Processors | 18 | September 19th 03 05:01 PM |
DDR Dual Channel Question | Dr. Mr. Horse | Overclocking AMD Processors | 2 | July 24th 03 11:10 AM |