If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
"ntoskrnl.exe error" message on overclocking?
Hi,
I recently bought 2500 Barton which I've popped into an Abit NF7-S, when I increase the FSB to 200 however (with all other settings at stock) I get a message on boot that "ntoskrnl.exe missing or corrupt" and XP fails to boot up....When I set it back to 2500 it boots up fine... I did manage to get it to boot last night after increasing the voltage to 1.75 but it still seemed unstable (crashed when running 3D-Mark 2003).... Does anyone know what this error message indicates? TIA (Using the following: 2500+ NF7-S v2 512mb Twinmos 3200 Geforce 4400ti) |
#2
|
|||
|
|||
Ben wrote: Hi, I recently bought 2500 Barton which I've popped into an Abit NF7-S, when I increase the FSB to 200 however (with all other settings at stock) I get a message on boot that "ntoskrnl.exe missing or corrupt" and XP fails to boot up....When I set it back to 2500 it boots up fine... I did manage to get it to boot last night after increasing the voltage to 1.75 but it still seemed unstable (crashed when running 3D-Mark 2003).... Does anyone know what this error message indicates? TIA (Using the following: 2500+ NF7-S v2 512mb Twinmos 3200 Geforce 4400ti) You need to throw some more juice to it, it'll be ok. I have to run my 8RDA+ at 1.8V to get prime 95 to run without errors. With a little more volts I can run the fsb up to 212. Roger |
#3
|
|||
|
|||
"Ben" schreef in bericht
om... Hi, I recently bought 2500 Barton which I've popped into an Abit NF7-S, when I increase the FSB to 200 however (with all other settings at stock) I get a message on boot that "ntoskrnl.exe missing or corrupt" and XP fails to boot up....When I set it back to 2500 it boots up fine... I did manage to get it to boot last night after increasing the voltage to 1.75 but it still seemed unstable (crashed when running 3D-Mark 2003).... Does anyone know what this error message indicates? Nothing, really. Unstable overclocked processor cause all sorts of miscellaneous error messages and crashes. It just means that your processor won't work at this clock frequency at this voltage. You may want to try increase the voltage even more (and shorten the life of your processor, sometimes extremely). -- V |
#4
|
|||
|
|||
sounds to me you got hd corruptions, lock the agp/pci setting to 100%, in
other words on your bios set it at 3/3 4/4 5/5 6/6 which ever you want "V" wrote in message ... "Ben" schreef in bericht om... Hi, I recently bought 2500 Barton which I've popped into an Abit NF7-S, when I increase the FSB to 200 however (with all other settings at stock) I get a message on boot that "ntoskrnl.exe missing or corrupt" and XP fails to boot up....When I set it back to 2500 it boots up fine... I did manage to get it to boot last night after increasing the voltage to 1.75 but it still seemed unstable (crashed when running 3D-Mark 2003).... Does anyone know what this error message indicates? Nothing, really. Unstable overclocked processor cause all sorts of miscellaneous error messages and crashes. It just means that your processor won't work at this clock frequency at this voltage. You may want to try increase the voltage even more (and shorten the life of your processor, sometimes extremely). -- V |
#5
|
|||
|
|||
Could be RAM, could be PCI, but definitely related to that 200 FSB. The 3200
RAM should be good unless you've tweaked the latency settings. Sounds just like a question I read earlier on the Anandtech OC forum. As it said there, not all 2500 Bartons make it to 200 FSB. JonB "Ben" wrote in message om... Hi, I recently bought 2500 Barton which I've popped into an Abit NF7-S, when I increase the FSB to 200 however (with all other settings at stock) I get a message on boot that "ntoskrnl.exe missing or corrupt" and XP fails to boot up....When I set it back to 2500 it boots up fine... I did manage to get it to boot last night after increasing the voltage to 1.75 but it still seemed unstable (crashed when running 3D-Mark 2003).... Does anyone know what this error message indicates? TIA (Using the following: 2500+ NF7-S v2 512mb Twinmos 3200 Geforce 4400ti) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AMD overclocking and semperon 3100s | [email protected] | General | 0 | November 24th 04 12:02 PM |
Looking for some medium-to-extreme overclocking advice | Cyde Weys | General | 4 | July 2nd 04 04:03 AM |
ABIT AI7 - Pentium®4 - 2.6GHz - Overclocking advice :) | Wayne Youngman | Overclocking | 23 | April 19th 04 12:02 PM |
OverClocking Guides | Phil Weldon | Overclocking | 0 | August 15th 03 05:41 AM |
Overclocking CPU & FSB (TBred B 2600+) | Wes Newell | Overclocking AMD Processors | 1 | July 18th 03 12:04 AM |