If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Cleaning pins on UK mains plugs
On Sun, 25 Apr 2004 18:18:44 UTC, Piotr Makley wrote:
I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. In many cases the pins look tarnished and I must have had some of these plugs for 10 or 20 years. The plugs all seem to work well and they do not heat up. But I thought it would be good practise to sandpaper the pins so they were shiny. Am I wasting my time? In this group (uk.comp.vendors), probably...it's massively OT. Perhaps you meant to post to uk.d-i-y ? -- Bob Eager begin by not using Outlook Express... |
#2
|
|||
|
|||
"Piotr Makley" wrote in message
... I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. In many cases the pins look tarnished and I must have had some of these plugs for 10 or 20 years. The plugs all seem to work well and they do not heat up. But I thought it would be good practise to sandpaper the pins so they were shiny. Am I wasting my time? Yes. Alun Harford |
#3
|
|||
|
|||
"Piotr Makley" wrote in message ... The plugs all seem to work well and they do not heat up. But I thought it would be good practise to sandpaper the pins so they were shiny. Am I wasting my time? ROFL !! Yeah I reckon you should sandpaper them. It's extremely important that they look good and fit in with the decor of the home whilst they're plugged in. ! LOL |
#4
|
|||
|
|||
"Piotr Makley" wrote in message ... I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. In many cases the pins look tarnished and I must have had some of these plugs for 10 or 20 years. The plugs all seem to work well and they do not heat up. But I thought it would be good practise to sandpaper the pins so they were shiny. Am I wasting my time? Unless you finish off with Brasso yes. and don't forget to do the wire inside too |
#5
|
|||
|
|||
"Trev" wrote in message
... "Piotr Makley" wrote in message ... I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. [snip] Am I wasting my time? Unless you finish off with Brasso yes. and don't forget to do the wire inside too One strand at a time, for optimal effect. Alex |
#6
|
|||
|
|||
Alex Fraser wrote: "Trev" wrote in message ... "Piotr Makley" wrote in message ... I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. [snip] Am I wasting my time? Unless you finish off with Brasso yes. and don't forget to do the wire inside too One strand at a time, for optimal effect. Alex Yes. Shininess reflects electricity, sort of like a mirror. Hence for maximum energy efficiency once must use highly polished wire. And no bends in the wire, either. No slowing down for the corners no stop or yield signs needed. Ken |
#7
|
|||
|
|||
In alt.engineering.electrical Piotr Makley wrote:
| I am in the UK and was wondering if there was any merit in cleaning | the brass pins of my three-pin mains plugs. | | In many cases the pins look tarnished and I must have had some of | these plugs for 10 or 20 years. | | The plugs all seem to work well and they do not heat up. But I | thought it would be good practise to sandpaper the pins so they | were shiny. | | Am I wasting my time? Why not just buy a shiny new plug and replace the old tarnished one? -- ----------------------------------------------------------------------------- | Phil Howard KA9WGN | http://linuxhomepage.com/ http://ham.org/ | | (first name) at ipal.net | http://phil.ipal.org/ http://ka9wgn.ham.org/ | ----------------------------------------------------------------------------- |
#8
|
|||
|
|||
On Sun, 25 Apr 2004 21:02:46 UTC, Ken Weitzel wrote:
And no bends in the wire, either. No slowing down for the corners no stop or yield signs needed. And fit the sockets near the ceiling, because gravity will help the leccy come down the cable. (it gets pumped up there by those miniature pumps they call MCBs). -- Bob Eager begin by not using Outlook Express... |
#9
|
|||
|
|||
Trev wrote:
"Piotr Makley" wrote in message ... I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. In many cases the pins look tarnished and I must have had some of these plugs for 10 or 20 years. The plugs all seem to work well and they do not heat up. But I thought it would be good practise to sandpaper the pins so they were shiny. Am I wasting my time? Unless you finish off with Brasso yes. and don't forget to do the wire inside too But don't forget, if they are very clean and make better contact - they will use more electricity, which in turn will lead to global warming. You have been warned and if we are flooded in the UK we will lay the blame at your door. |
#10
|
|||
|
|||
"Malev" wrote in message ... On Sun, 25 Apr 2004 19:18:44 +0100, Piotr Makley wrote: I am in the UK and was wondering if there was any merit in cleaning the brass pins of my three-pin mains plugs. In many cases the pins look tarnished and I must have had some of these plugs for 10 or 20 years. The plugs all seem to work well and they do not heat up. But I thought it would be good practise to sandpaper the pins so they were shiny. Am I wasting my time? Under the terms of The Clean Pins Act 2003, you are legally obliged to ensure that all 3 pins are exempt of any deposit whatsoever and shine to BS 6907 specifications. The newly formed Pin Inspection Special Squad (P.I.S.S.) has power of entry to inspect all your plugs, whether connected to the mains or not. And further more the Pin Inspection Special Squad have the power to remove offending items to be safely disposed of. This is known as taking the P.I.S.S. PC |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HP Deskjet 1220 Cleaning Kit problem | Matti Partonen | Printers | 5 | November 11th 04 01:04 AM |
DAT drive recommendations? | Jonathan Sachs | Storage (alternative) | 34 | October 14th 04 01:44 PM |
USB Pins...again | Howard | Gigabyte Motherboards | 0 | October 27th 03 04:54 PM |
Dial up modem problem | Richard Freeman | Homebuilt PC's | 21 | September 22nd 03 05:50 AM |
Vuescan, IR cleaning, which film scanner? | Sanaka | Scanners | 1 | August 21st 03 04:24 PM |