If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Quick Poll - 40mm - 60mm - 80mm - 92mm Fan on your Heatsink?
Subject header says it all. . .
I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . |
#2
|
|||
|
|||
"Wayne Youngman" wrote in message ... Subject header says it all. . . I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . 80mm with 86cm adapter on Copper Sink. XP2000+ Palimino Load/Idle at ~42 |
#3
|
|||
|
|||
80mm Panaflo M1BX on Thermalright AX-478
|
#4
|
|||
|
|||
92mm is the way to go if your heatsink is big enough. 60cfm at 35db for the
38mm thick fans is superb performance. rms |
#5
|
|||
|
|||
Epox 8RDA3+ 227 FSB Northbridge : Slim Volcano + 80mm =19CFM
XP1700 DUT3C 10.0 - 2270 MHz : Volcano 9 + 80mm = 75CFM Gigabyte Radeon 9700 Pro - 393/371 : Slim Volcano + 92mm = 52CFM Maxtor DM 9 - 92mm = 52CFM Vantec 4-channel Fan Control Air - 41/55C "Wayne Youngman" wrote in message ... Subject header says it all. . . I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . |
#6
|
|||
|
|||
"Wayne Youngman" wrote in
: Subject header says it all. . . I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . 60mm delta screamer (the infamous "black label" delta) on an OCZ gladiator (all copper thin fin HS) 1300 duron, at 1300 runs low high 30's to low 40's idle, and like mid 40s to low 50s at full load. |
#7
|
|||
|
|||
92mm Papst fan on Alpha PAL8045 heatsink with selfmade adaptor.
|
#8
|
|||
|
|||
Wayne Youngman wrote:
Subject header says it all. . . I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . 80 mm on SLK-800 and 80 mm on a volcano 9. 60 mm on 6 stock AMD sinks. 60 mm on a stock PIII 1bGhz cooler 40 mm on 4 AT machines. |
#9
|
|||
|
|||
"Wayne Youngman" wrote in message
... Subject header says it all. . . I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . 70mm fan sitting at 90% to the HS in a Coolermaster Aero 7+ on my XP 2800+ Barton - runs at around 44 deg C idle, 49/50deg C load. -- Sparky |
#10
|
|||
|
|||
"Wayne Youngman" wrote in message ...
Subject header says it all. . . I use a 40mm Fan, its part of the retail FC-PGA PIII heatsink running a 550e @ 733Mhz - Load 41c - I'm in the UK. . . 70mm YS Tech TMD fan (36 CFM), Glacial Tech Igloo 2500, Tbred B XP1700+ @2.1 Ghz, 38 degrees @idle, 42 @load. |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
80mm vs 92mm Fan? | Wayne Youngman | Overclocking | 7 | March 28th 04 12:22 PM |
Quick Poll - 40mm - 60mm - 80mm - 92mm Fan on your Heatsink? | Wayne Youngman | Overclocking | 11 | July 29th 03 09:09 AM |