If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Please Help - DCOM Error When Burning CD's With Roxio EZ-CD Software - Dell Latitude C840
I see the following error reported in - Control Panel Administrative
Tools Component Services Event Viewer (local) System - each time I burn a CD-R with Roxio EZ-CD Creator software on my Dell Latitude C840 Laptop. The CD burn completes okay. (I also use Nero burning software which gives no errors.) Would someone please tell me what this is and how to nix it. I Have tried turning DCOM off, and gone through the local registry, but the exact source of the error is difficult to find: Event Type: Error Event Source: DCOM Event Category: None Event ID: 10010 Date: 4/18/2004 Time: 1:48:35 PM Description: The server {520CCA63-51A5-11D3-9144-00104BA11C5E} did not register with DCOM within the required timeout. Regards, -Art |
#2
|
|||
|
|||
Does it actually cause a problem? If not, why not ignore it?
"The_AntiArt" wrote in message ... I see the following error reported in - Control Panel Administrative Tools Component Services Event Viewer (local) System - each time I burn a CD-R with Roxio EZ-CD Creator software on my Dell Latitude C840 Laptop. The CD burn completes okay. (I also use Nero burning software which gives no errors.) Would someone please tell me what this is and how to nix it. I Have tried turning DCOM off, and gone through the local registry, but the exact source of the error is difficult to find: Event Type: Error Event Source: DCOM Event Category: None Event ID: 10010 Date: 4/18/2004 Time: 1:48:35 PM Description: The server {520CCA63-51A5-11D3-9144-00104BA11C5E} did not register with DCOM within the required timeout. Regards, -Art |
#3
|
|||
|
|||
On Sun, 18 Apr 2004 18:55:43 -0400, "Tom Scales"
wrote: Does it actually cause a problem? If not, why not ignore it? I can only say that on the surface, it does not appear to create a "problem" in that most CD-R burns complete successfully. However, there are always the possibility of other negative effects not yet identified. The error is being reported for a reason which should be definable. I would like to improve my knowledge and understanding of the workings of Windows XP Professional "under the hood" and at the same time eliminate a red error flag which really should not be there. |
#4
|
|||
|
|||
"The_AntiArt" wrote in message ... Event Type: Error Event Source: DCOM Event Category: None Event ID: 10010 Date: 4/18/2004 Time: 1:48:35 PM Description: The server {520CCA63-51A5-11D3-9144-00104BA11C5E} did not register with DCOM within the required timeout. Regards, -Art http://www.eventid.net/display.asp?e...10&source=DCOM -- D I'm not an MVP a VIP nor do I have ESP. I was just trying to help. Please use your own best judgment before implementing any suggestions or advice herein. No warranty is expressed or implied. Your mileage may vary. See store for details. Remove shoes to E-mail. |
#5
|
|||
|
|||
Bang 'em in the azz
"The_AntiArt" wrote in message ... I see the following error reported in - Control Panel Administrative Tools Component Services Event Viewer (local) System - each time I burn a CD-R with Roxio EZ-CD Creator software on my Dell Latitude C840 Laptop. The CD burn completes okay. (I also use Nero burning software which gives no errors.) Would someone please tell me what this is and how to nix it. I Have tried turning DCOM off, and gone through the local registry, but the exact source of the error is difficult to find: Event Type: Error Event Source: DCOM Event Category: None Event ID: 10010 Date: 4/18/2004 Time: 1:48:35 PM Description: The server {520CCA63-51A5-11D3-9144-00104BA11C5E} did not register with DCOM within the required timeout. Regards, -Art |
#6
|
|||
|
|||
On Sun, 18 Apr 2004 19:25:57 -0400, "HillBillyBuddhist"
wrote: Thanks! -Art |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
"Unable to recover TOC" - when burning audio with Nero | Neil | Cdr | 1 | July 16th 04 11:25 AM |
ND-1300A not supporting burning CDs in DMA mode | Ville Portti | Cdr | 0 | April 15th 04 02:17 PM |
Is my hard drive the source of my CD burning woes? | Jonathan King | General | 4 | March 19th 04 12:06 AM |
Conflict between 2 CD/DVD burning software | Rick | General | 2 | January 2nd 04 11:09 PM |
When burning with Windows 2000 server pc becomes unusable | KJ | Cdr | 1 | August 28th 03 02:27 PM |