If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Connecting front panel USB
Hi G;uys,
need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong Thanks Guys Regards Bob |
#2
|
|||
|
|||
Connecting front panel USB
Sorry Guys,
the First Case Wire Connector on the is VCC not VSS "BH2" wrote in message ... Hi Guys, need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong Thanks Guys Regards Bob |
#3
|
|||
|
|||
Connecting front panel USB
BH2 wrote:
Sorry Guys, the First Case Wire Connector on the is VCC not VSS "BH2" wrote in message ... Hi Guys, need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong The Pwr 5V goes to the VCC The Gnd should be obvious. The USB+ and USB- goes to say the DX+ and DX-, use the same letter after the D. There is obviously enough for two front panel connectors on the motherboard header. |
#4
|
|||
|
|||
Connecting front panel USB
BH2 wrote:
Hi G;uys, need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong Thanks Guys Regards Bob PWR_5V = VCC DX- = USB- DX+ = USB+ GND = GND The 2x5 has room for two 1x4 patterns, as in the above table. Just make sure the power and ground go in the right place. That is the most important part. Paul |
#5
|
|||
|
|||
Connecting front panel USB
Thanks Rod
Regards Bob "Rod Speed" wrote in message ... BH2 wrote: Sorry Guys, the First Case Wire Connector on the is VCC not VSS "BH2" wrote in message ... Hi Guys, need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong The Pwr 5V goes to the VCC The Gnd should be obvious. The USB+ and USB- goes to say the DX+ and DX-, use the same letter after the D. There is obviously enough for two front panel connectors on the motherboard header. |
#6
|
|||
|
|||
Connecting front panel USB
Thanks Paul,
Building a Computer is not that easy, different boards different pins. Regards Bob "Paul" wrote in message ... BH2 wrote: Hi G;uys, need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong Thanks Guys Regards Bob PWR_5V = VCC DX- = USB- DX+ = USB+ GND = GND The 2x5 has room for two 1x4 patterns, as in the above table. Just make sure the power and ground go in the right place. That is the most important part. Paul |
#7
|
|||
|
|||
Connecting front panel USB
"Paul" wrote in message ... BH2 wrote: Hi G;uys, need some advice please just buil a new computer with new Mobo But using the same case, would like to know which wire do I connect to which Mobo pins Mobo 1. Pwr 5v 2. Pwr 5v 3. USB DX- 4. USB Dy- 5. USBDX+ 6. USB Dy+ 7. Gnd 8. Gnd 9. No pin 10. NC Case Wire connectors 1. VSS 2. UBS+ 3. USB- 4. Gnd Think I know but don't want to get it wrong Thanks Guys Regards Bob PWR_5V = VCC DX- = USB- DX+ = USB+ GND = GND The 2x5 has room for two 1x4 patterns, as in the above table. Just make sure the power and ground go in the right place. That is the most important part. Paul I always refer to this information when I get confused: http://www.frontx.com/cpx101_2.html Seems to explain it nicely. Charlie |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
connecting to front USB panel | Shirl | Gigabyte Motherboards | 4 | January 20th 07 09:55 PM |
Connecting front panel audio | trevaaaaaaa | Homebuilt PC's | 6 | May 4th 06 10:49 AM |
Connecting Enermax front panel audio to Asus A7V600-X | forumposter32 | Asus Motherboards | 7 | May 24th 05 11:06 PM |
Need Help Connecting Front Case Panel USB Ports to A7N8X-E | [email protected] | Asus Motherboards | 3 | February 15th 04 04:55 PM |
Connecting front USB ports | Bri | Homebuilt PC's | 4 | February 12th 04 11:22 PM |