If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Blinking Amber Power Button on Precision 390
I have a Precision Workstation 390 with the power button blinking.
According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W |
#2
|
|||
|
|||
Blinking Amber Power Button on Precision 390
On Monday, January 27, 2014 1:14:17 AM UTC-5, W wrote:
I have a Precision Workstation 390 with the power button blinking. According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W Here's a visual test: Open up the case and inspect the motherboard for failed capacitors. A failed capacitor has either a bulging top or discoloration from leakage. One bad capacitor and the motherboard is history, not worth the repair. Here's a practical test: Disconnect the power supply from the motherboard and ALL devices. Take another known-good ATX12v 24-pin power supply with long enough wire leads, and connect it to the 24-pin and 4-pin connectors on the motherboard. Push power button to see what happens. if the board powers up to a BIOS screen, the original power supply has gone bad. If you get the same blinking amber power button light, the motherboard has failed. Note that you do not need a power supply that is physically the same as the one in the 390 right now. The 24-pin and 4-pin power connectors are all that matters, because they are standard. And save yourself some time. Don't even remove the power supply from the 390. Just attach the other power supply from outside the chassis. Over the last several months, I got a number of systems from a local company that upgraded or replaced Precision 380, Precision 390 and Precision T3400 boxes, all with the same chassis and nearly identical power supplies. One or two had leaky capacitors. I have another T3400 motherboard in a case, awaiting testing (my time is limited, haven't gotten to it), and then a replacement power supply. I may take one from a Precision 380, 'cause the Core 2 Quad T3400 is a much better than a dual core 380... Ben Myers |
#3
|
|||
|
|||
Blinking Amber Power Button on Precision 390
So here is an interesting result:
1) First, it is a Precision 380 not 390 2) Power supply is apparently good. But the strange result is that the system only blinks once you plug into the motherboard mini connector labeled "P2". If you only plug into the main motherboard connector, everything works. P2 is located in the vicinity of the CD ROM drive cage. What does P2 control, and what would this symptom mean? I'm guessing that P2 must power some fan like the CPU fan that is a discrete component? Perhaps the failure here is on that fan? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 1:14:17 AM UTC-5, W wrote: I have a Precision Workstation 390 with the power button blinking. According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W Here's a visual test: Open up the case and inspect the motherboard for failed capacitors. A failed capacitor has either a bulging top or discoloration from leakage. One bad capacitor and the motherboard is history, not worth the repair. Here's a practical test: Disconnect the power supply from the motherboard and ALL devices. Take another known-good ATX12v 24-pin power supply with long enough wire leads, and connect it to the 24-pin and 4-pin connectors on the motherboard. Push power button to see what happens. if the board powers up to a BIOS screen, the original power supply has gone bad. If you get the same blinking amber power button light, the motherboard has failed. Note that you do not need a power supply that is physically the same as the one in the 390 right now. The 24-pin and 4-pin power connectors are all that matters, because they are standard. And save yourself some time. Don't even remove the power supply from the 390. Just attach the other power supply from outside the chassis. Over the last several months, I got a number of systems from a local company that upgraded or replaced Precision 380, Precision 390 and Precision T3400 boxes, all with the same chassis and nearly identical power supplies. One or two had leaky capacitors. I have another T3400 motherboard in a case, awaiting testing (my time is limited, haven't gotten to it), and then a replacement power supply. I may take one from a Precision 380, 'cause the Core 2 Quad T3400 is a much better than a dual core 380... Ben Myers |
#4
|
|||
|
|||
Blinking Amber Power Button on Precision 390
"W" wrote in message
... So here is an interesting result: 1) First, it is a Precision 380 not 390 2) Power supply is apparently good. But the strange result is that the system only blinks once you plug into the motherboard mini connector labeled "P2". If you only plug into the main motherboard connector, everything works. P2 is located in the vicinity of the CD ROM drive cage. What does P2 control, and what would this symptom mean? I'm guessing that P2 must power some fan like the CPU fan that is a discrete component? Perhaps the failure here is on that fan? The power cable labeled P2 goes to a connector named 12VPOWER in the Precision 380 Quick Reference Guide. So with 12VPOWER connected, the front panel blinks an Orange light on the power button. NONE of the four green or amber diagnostic lights are powered on. Looks like some kind of short connected to that 12VPOWER? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 1:14:17 AM UTC-5, W wrote: I have a Precision Workstation 390 with the power button blinking. According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W Here's a visual test: Open up the case and inspect the motherboard for failed capacitors. A failed capacitor has either a bulging top or discoloration from leakage. One bad capacitor and the motherboard is history, not worth the repair. Here's a practical test: Disconnect the power supply from the motherboard and ALL devices. Take another known-good ATX12v 24-pin power supply with long enough wire leads, and connect it to the 24-pin and 4-pin connectors on the motherboard. Push power button to see what happens. if the board powers up to a BIOS screen, the original power supply has gone bad. If you get the same blinking amber power button light, the motherboard has failed. Note that you do not need a power supply that is physically the same as the one in the 390 right now. The 24-pin and 4-pin power connectors are all that matters, because they are standard. And save yourself some time. Don't even remove the power supply from the 390. Just attach the other power supply from outside the chassis. Over the last several months, I got a number of systems from a local company that upgraded or replaced Precision 380, Precision 390 and Precision T3400 boxes, all with the same chassis and nearly identical power supplies. One or two had leaky capacitors. I have another T3400 motherboard in a case, awaiting testing (my time is limited, haven't gotten to it), and then a replacement power supply. I may take one from a Precision 380, 'cause the Core 2 Quad T3400 is a much better than a dual core 380... Ben Myers |
#5
|
|||
|
|||
Blinking Amber Power Button on Precision 390
On Monday, January 27, 2014 8:51:56 PM UTC-5, W wrote:
"W" wrote in message ... So here is an interesting result: 1) First, it is a Precision 380 not 390 2) Power supply is apparently good. But the strange result is that the system only blinks once you plug into the motherboard mini connector labeled "P2". If you only plug into the main motherboard connector, everything works. P2 is located in the vicinity of the CD ROM drive cage. What does P2 control, and what would this symptom mean? I'm guessing that P2 must power some fan like the CPU fan that is a discrete component? Perhaps the failure here is on that fan? The power cable labeled P2 goes to a connector named 12VPOWER in the Precision 380 Quick Reference Guide. So with 12VPOWER connected, the front panel blinks an Orange light on the power button. NONE of the four green or amber diagnostic lights are powered on. Looks like some kind of short connected to that 12VPOWER? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 1:14:17 AM UTC-5, W wrote: I have a Precision Workstation 390 with the power button blinking. According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W Here's a visual test: Open up the case and inspect the motherboard for failed capacitors. A failed capacitor has either a bulging top or discoloration from leakage. One bad capacitor and the motherboard is history, not worth the repair. Here's a practical test: Disconnect the power supply from the motherboard and ALL devices. Take another known-good ATX12v 24-pin power supply with long enough wire leads, and connect it to the 24-pin and 4-pin connectors on the motherboard. Push power button to see what happens. if the board powers up to a BIOS screen, the original power supply has gone bad. If you get the same blinking amber power button light, the motherboard has failed. Note that you do not need a power supply that is physically the same as the one in the 390 right now. The 24-pin and 4-pin power connectors are all that matters, because they are standard. And save yourself some time. Don't even remove the power supply from the 390. Just attach the other power supply from outside the chassis. Over the last several months, I got a number of systems from a local company that upgraded or replaced Precision 380, Precision 390 and Precision T3400 boxes, all with the same chassis and nearly identical power supplies. One or two had leaky capacitors. I have another T3400 motherboard in a case, awaiting testing (my time is limited, haven't gotten to it), and then a replacement power supply. I may take one from a Precision 380, 'cause the Core 2 Quad T3400 is a much better than a dual core 380... Ben Myers Are you 1000% sure that the power supply is good? Is this the same power supply as the original? If so, you really and truly do need to test with another known good power supply. This is the only way to isolate with reasonable certainty whether the motherboard is bad or the power supply. (Well, there is very small chance that either CPU or memory is bad, but very unlikely.) That is EXACTLY what is running on my bench right now: A Precision 390 motherboard, video card, memory, flash stick with MEMTEST+ running, and a standard sized Antec power supply with all sorts of long connectors. The board seems to be OK, so I need to get a power supply to complete a very nice Core 2 Quad system... Ben Myers |
#6
|
|||
|
|||
Blinking Amber Power Button on Precision 390
Sorry to top post, but my newsreader is not quoting correctly.
Yes, we tested with a NEW power supply. Power to the main connector on the motherboard shows no error on the front light and the system starts to power on. As soon as the 12VPOWER on P2 is connected to the motherboard, we get the flashing amber light, duplicating exactly the symptom with the original power supply. And correction: we have a Precision 380 not a 390. They take the same power supply. And I would gladly send you our original one, but unfortunately it was destroyed in process of removal (someone cut cables to remove from the tight placement. Any idea on what the 12VPOWER on P2 is connecting to? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 8:51:56 PM UTC-5, W wrote: "W" wrote in message ... So here is an interesting result: 1) First, it is a Precision 380 not 390 2) Power supply is apparently good. But the strange result is that the system only blinks once you plug into the motherboard mini connector labeled "P2". If you only plug into the main motherboard connector, everything works. P2 is located in the vicinity of the CD ROM drive cage. What does P2 control, and what would this symptom mean? I'm guessing that P2 must power some fan like the CPU fan that is a discrete component? Perhaps the failure here is on that fan? The power cable labeled P2 goes to a connector named 12VPOWER in the Precision 380 Quick Reference Guide. So with 12VPOWER connected, the front panel blinks an Orange light on the power button. NONE of the four green or amber diagnostic lights are powered on. Looks like some kind of short connected to that 12VPOWER? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 1:14:17 AM UTC-5, W wrote: I have a Precision Workstation 390 with the power button blinking. According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W Here's a visual test: Open up the case and inspect the motherboard for failed capacitors. A failed capacitor has either a bulging top or discoloration from leakage. One bad capacitor and the motherboard is history, not worth the repair. Here's a practical test: Disconnect the power supply from the motherboard and ALL devices. Take another known-good ATX12v 24-pin power supply with long enough wire leads, and connect it to the 24-pin and 4-pin connectors on the motherboard. Push power button to see what happens. if the board powers up to a BIOS screen, the original power supply has gone bad. If you get the same blinking amber power button light, the motherboard has failed. Note that you do not need a power supply that is physically the same as the one in the 390 right now. The 24-pin and 4-pin power connectors are all that matters, because they are standard. And save yourself some time. Don't even remove the power supply from the 390. Just attach the other power supply from outside the chassis. Over the last several months, I got a number of systems from a local company that upgraded or replaced Precision 380, Precision 390 and Precision T3400 boxes, all with the same chassis and nearly identical power supplies. One or two had leaky capacitors. I have another T3400 motherboard in a case, awaiting testing (my time is limited, haven't gotten to it), and then a replacement power supply. I may take one from a Precision 380, 'cause the Core 2 Quad T3400 is a much better than a dual core 380... Ben Myers Are you 1000% sure that the power supply is good? Is this the same power supply as the original? If so, you really and truly do need to test with another known good power supply. This is the only way to isolate with reasonable certainty whether the motherboard is bad or the power supply. (Well, there is very small chance that either CPU or memory is bad, but very unlikely.) That is EXACTLY what is running on my bench right now: A Precision 390 motherboard, video card, memory, flash stick with MEMTEST+ running, and a standard sized Antec power supply with all sorts of long connectors. The board seems to be OK, so I need to get a power supply to complete a very nice Core 2 Quad system... Ben Myers |
#7
|
|||
|
|||
Blinking Amber Power Button on Precision 390
On Wednesday, January 29, 2014 5:15:05 AM UTC-5, W wrote:
Sorry to top post, but my newsreader is not quoting correctly. Yes, we tested with a NEW power supply. Power to the main connector on the motherboard shows no error on the front light and the system starts to power on. As soon as the 12VPOWER on P2 is connected to the motherboard, we get the flashing amber light, duplicating exactly the symptom with the original power supply. And correction: we have a Precision 380 not a 390. They take the same power supply. And I would gladly send you our original one, but unfortunately it was destroyed in process of removal (someone cut cables to remove from the tight placement. Any idea on what the 12VPOWER on P2 is connecting to? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 8:51:56 PM UTC-5, W wrote: "W" wrote in message ... So here is an interesting result: 1) First, it is a Precision 380 not 390 2) Power supply is apparently good. But the strange result is that the system only blinks once you plug into the motherboard mini connector labeled "P2". If you only plug into the main motherboard connector, everything works. P2 is located in the vicinity of the CD ROM drive cage. What does P2 control, and what would this symptom mean? I'm guessing that P2 must power some fan like the CPU fan that is a discrete component? Perhaps the failure here is on that fan? The power cable labeled P2 goes to a connector named 12VPOWER in the Precision 380 Quick Reference Guide. So with 12VPOWER connected, the front panel blinks an Orange light on the power button. NONE of the four green or amber diagnostic lights are powered on. Looks like some kind of short connected to that 12VPOWER? -- W "Ben Myers" wrote in message ... On Monday, January 27, 2014 1:14:17 AM UTC-5, W wrote: I have a Precision Workstation 390 with the power button blinking. According to Troubleshooting section, this means either a bad power supply or a failing system board. Is there any test that will help me isolate it further? -- W Here's a visual test: Open up the case and inspect the motherboard for failed capacitors. A failed capacitor has either a bulging top or discoloration from leakage. One bad capacitor and the motherboard is history, not worth the repair. Here's a practical test: Disconnect the power supply from the motherboard and ALL devices. Take another known-good ATX12v 24-pin power supply with long enough wire leads, and connect it to the 24-pin and 4-pin connectors on the motherboard. Push power button to see what happens. if the board powers up to a BIOS screen, the original power supply has gone bad. If you get the same blinking amber power button light, the motherboard has failed. Note that you do not need a power supply that is physically the same as the one in the 390 right now. The 24-pin and 4-pin power connectors are all that matters, because they are standard. And save yourself some time.. Don't even remove the power supply from the 390. Just attach the other power supply from outside the chassis. Over the last several months, I got a number of systems from a local company that upgraded or replaced Precision 380, Precision 390 and Precision T3400 boxes, all with the same chassis and nearly identical power supplies. One or two had leaky capacitors. I have another T3400 motherboard in a case, awaiting testing (my time is limited, haven't gotten to it), and then a replacement power supply. I may take one from a Precision 380, 'cause the Core 2 Quad T3400 is a much better than a dual core 380... Ben Myers Are you 1000% sure that the power supply is good? Is this the same power supply as the original? If so, you really and truly do need to test with another known good power supply. This is the only way to isolate with reasonable certainty whether the motherboard is bad or the power supply. (Well, there is very small chance that either CPU or memory is bad, but very unlikely.) That is EXACTLY what is running on my bench right now: A Precision 390 motherboard, video card, memory, flash stick with MEMTEST+ running, and a standard sized Antec power supply with all sorts of long connectors. The board seems to be OK, so I need to get a power supply to complete a very nice Core 2 Quad system... Ben Myers 12VPOWER on P2 supplies the 12v required by all motherboards with Intel CPUs socket 478 and newer, whether BTX like the Precision 380 or ATX like others. If you got the same result with a new power supply as with the original, the motherboard is most likely the culprit and it is ready to be recycled. There is an outside chance something happened to the LGA775 CPU in the board, so if you have a spare, substitute and test again. But the odds strongly favor a malfunctioning motherboard... Ben Myers |
#8
|
|||
|
|||
Blinking Amber Power Button on Precision 390
On Mon, 27 Jan 2014 17:51:56 -0800, "W"
wrote: "W" wrote in message ... So here is an interesting result: 1) First, it is a Precision 380 not 390 2) Power supply is apparently good. But the strange result is that the system only blinks once you plug into the motherboard mini connector labeled "P2". If you only plug into the main motherboard connector, everything works. P2 is located in the vicinity of the CD ROM drive cage. What does P2 control, and what would this symptom mean? I'm guessing that P2 must power some fan like the CPU fan that is a discrete component? Perhaps the failure here is on that fan? The power cable labeled P2 goes to a connector named 12VPOWER in the Precision 380 Quick Reference Guide. I think that's it. You've figured it out. The Quick Reference Guide is broken. Disconnect it and you'll be okay. Sometimes the QRG is printed on glossy paper and that can cause trouble. Also, whatever Ben says. So with 12VPOWER connected, the front panel blinks an Orange light on the power button. NONE of the four green or amber diagnostic lights are powered on. Looks like some kind of short connected to that 12VPOWER? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Precision 390 How to Shut Off Windows with Power Button? | W[_3_] | Dell Computers | 3 | September 16th 13 02:25 PM |
PC doesn't turn on, but power button & LED are blinking. | Andy[_14_] | Homebuilt PC's | 1 | August 28th 10 02:52 AM |
Power buttom amber, will not power on. | PaulC95 | Gateway Computers | 1 | July 16th 07 11:27 PM |
Power light blinking (amber color) | drw4e | Dell Computers | 12 | November 30th 06 03:43 AM |
4pin pentium power connector scorched - computer shuts off - blinking amber instead of green light | Bill Gates | General | 5 | August 24th 06 11:23 PM |