If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Help me ID this ATI graphics card
On Thu, 22 Apr 2004 18:36:37 +0100, Sal Amie wrote:
I have this old graphics card which I am trying to identify. It is labelled Sept 1999. The circuit board has a logo on the circuit side which says "graphics by ATI Rage 128" So it's an ATI Rage 128 or 128 Pro. On the components side of the circuit board it says ""C in a circle"" (copyright) 1999 ATI Technologies Inc. (1) Does this mean the board is actually made by ATI or is it probbaly made by someone else using an ATI Rage chip? (I didn't think grahhics chip companies like ATI made complete graphics boards.) Doesn't really matter who made it, the standard driver offered by ATI, most current version, is typically the best to use regardless of who made it. (2) Also on the circuit board it says "N625". What does this mean? Don't know, don't think it matters. (3) Another paper label (with a barcode) says R128 GL 32M" but I can't find that on the Web. 32MB of memory, suggests it's the "Pro" version. Fortunately that means it will work on modern boards, not only the 3.3V AGP1 boards. (4) One of the chips has a paper label saying "R128 66501" Sounds like it might be the bios EPROM, not necessary to consider. Can someone tell me what board this is and which of those bits of info were ther key indentifiers. Go here, http://www.ati.com/support/driver.html select the OS, "graphics driver", and "Rage 128 Pro" The next page would offer the driver and Tuner/Capture software. If this isn't an All-In-Wonder, which it doesn't seem to be, you most likely do not need the Tuner/Capture software. However if the card does have an S-video input jack then that capture software could be needed. Another question I would like to ask is .... is this graphics card any better than the integrated video on modern boards using the latest integrated graphics chips like the "NVIDIA nForce2 IGP"? (E.G. the Asus AV8NX-VM motherboard) It should be similar or perhaps a little better at display crispness (which can vary from card to card, you'll have to try that and see for yourself). The motherboard example you gave it wrong/mistyped or something. Asus has an A7V8X-VM, Via chipset integrated video, or an A7N8X-VM, nForce2 integrated video. Either of those OR the ATI 128 are plenty fast enough for 2D usage, movie/DVD playback, etc. The ATI 128 is, IIRC, just a little bit slower than the A7V8X-VM's video in 3D gaming, but much, much slower than the A7N8X-VM's video, providing you use 2 memory modules for dual channel mode. However for 3D gaming, any modern mid to high-end video card would be faster than any of the above. |
#2
|
|||
|
|||
Sal Amie wrote:
I have this old graphics card which I am trying to identify. It is labelled Sept 1999. The circuit board has a logo on the circuit side which says "graphics by ATI Rage 128" On the components side of the circuit board it says ""C in a circle"" (copyright) 1999 ATI Technologies Inc. (1) Does this mean the board is actually made by ATI or is it probbaly made by someone else using an ATI Rage chip? (I didn't think grahhics chip companies like ATI made complete graphics boards.) Well that's where you're wrong, you see. ATI make their own boards - Nvidia never have. Just visit ATI's site. |
#3
|
|||
|
|||
uh.....lessee.......
click RUN type in "cmd" enter type in "DEBUG" enter type in "d c000:0010" enter type in "d" enter a couple times for a couple more screens until you get to the part of the Video BIOS that has the model # you want to see. It should tell you what it is. when you're done, type in "q" enter {for quit} Of course enter is the enter key and the parts in "" are what you type (without the "" quotes. On Thu, 22 Apr 2004 18:36:37 +0100, Sal Amie wrote: I have this old graphics card which I am trying to identify. It is labelled Sept 1999. The circuit board has a logo on the circuit side which says "graphics by ATI Rage 128" On the components side of the circuit board it says ""C in a circle"" (copyright) 1999 ATI Technologies Inc. (1) Does this mean the board is actually made by ATI or is it probbaly made by someone else using an ATI Rage chip? (I didn't think grahhics chip companies like ATI made complete graphics boards.) (2) Also on the circuit board it says "N625". What does this mean? (3) Another paper label (with a barcode) says R128 GL 32M" but I can't find that on the Web. (4) One of the chips has a paper label saying "R128 66501" Can someone tell me what board this is and which of those bits of info were ther key indentifiers. --- Another question I would like to ask is .... is this graphics card any better than the integrated video on modern boards using the latest integrated graphics chips like the "NVIDIA nForce2 IGP"? (E.G. the Asus AV8NX-VM motherboard) ~~~~~~ Bait for spammers: root@localhost postmaster@localhost admin@localhost abuse@localhost ] ~~~~~~ Remove "spamless" to email me. |
#4
|
|||
|
|||
"Overlord" wrote in message ... uh.....lessee....... click RUN type in "cmd" enter type in "DEBUG" enter type in "d c000:0010" enter type in "d" enter a couple times for a couple more screens until you get to the part of the Video BIOS that has the model # you want to see. It should tell you what it is. when you're done, type in "q" enter {for quit} Of course enter is the enter key and the parts in "" are what you type (without the "" quotes. OUCH!! Been doing this a while, eh? Remember how to format an MFM drive in debug? |
#5
|
|||
|
|||
Noozer wrote:
"Overlord" wrote in message ... uh.....lessee....... click RUN type in "cmd" enter type in "DEBUG" enter type in "d c000:0010" enter type in "d" enter a couple times for a couple more screens until you get to the part of the Video BIOS that has the model # you want to see. It should tell you what it is. when you're done, type in "q" enter {for quit} Of course enter is the enter key and the parts in "" are what you type (without the "" quotes. OUCH!! Been doing this a while, eh? Remember how to format an MFM drive in debug? Oh, man. Talk about dredging up nasty memories. I used to be so good at making typos in the worst possible places when using debug - and I remember managing to permanently ruin an MFM drive. It was a 5 MB or 10 MB drive and cost more than I made in a month. |
#6
|
|||
|
|||
On Fri, 23 Apr 2004 02:44:04 GMT, "Noozer" wrote:
"Overlord" wrote in message .. . uh.....lessee....... click RUN type in "cmd" enter type in "DEBUG" enter type in "d c000:0010" enter type in "d" enter a couple times for a couple more screens until you get to the part of the Video BIOS that has the model # you want to see. It should tell you what it is. when you're done, type in "q" enter {for quit} Of course enter is the enter key and the parts in "" are what you type (without the "" quotes. OUCH!! Been doing this a while, eh? Remember how to format an MFM drive in debug? Sometimes the old tricks work bestG. I seem to remember formatting floppies that way. I recall keeping a cheap generic config.sys and autoexec.bat on the root and editing command.com so it looked for and used files other than those to fire up. Didn't want some empty headed installation program editing my baby; my 10 or 12 page autoexec.bat and almost as large config.sys. I remember making 50 character init$ for modems. I remember typing in switches to make zmodem file transfers from the DOS prompt... But there got to be so many protocols; Xmodem, Ymodem, Zmodem, DSZmodem, GSZmodem, FASTmodem, Hydra, Imodem, HSlink, DSZ Qmodem G, IceZmodem, Jmodem, Tmodem, VisualZmodem, Smodem, VXY Xmodem 1k.... and each one had it's variants. I forget the more exotic and obscure protocols now, used a couple dozen I guess. Eventually I had to put them all in a batch file as each would have a line of switches. Typing in a simple Xmodem transfer and find you're adding a Kermit switch is a Bad Thing. Forgot a hell of a lot since then..... ~~~~~~ Bait for spammers: root@localhost postmaster@localhost admin@localhost abuse@localhost ] ~~~~~~ Remove "spamless" to email me. |
#7
|
|||
|
|||
On Thu, 22 Apr 2004 21:16:01 -0600, Rob Stow wrote:
Noozer wrote: "Overlord" wrote in message ... uh.....lessee....... click RUN type in "cmd" enter type in "DEBUG" enter type in "d c000:0010" enter type in "d" enter a couple times for a couple more screens until you get to the part of the Video BIOS that has the model # you want to see. It should tell you what it is. when you're done, type in "q" enter {for quit} Of course enter is the enter key and the parts in "" are what you type (without the "" quotes. OUCH!! Been doing this a while, eh? Remember how to format an MFM drive in debug? Oh, man. Talk about dredging up nasty memories. I used to be so good at making typos in the worst possible places when using debug - and I remember managing to permanently ruin an MFM drive. It was a 5 MB or 10 MB drive and cost more than I made in a month. But doublespace was great. Almost doubled your storage. You ever find that huge file on that G or H partition and delete it for the space.... and find that was your entire C drive in a single compressed file on a sneaky partition? I forget what the name of the util was before M$ stole it... Remember using Copy con for cobbling your files and then when they didn't work using Debug or Edlin to troubleshoot 'em? I remember kids bringing me dual 5¼ floppy systems and wanting me to make it so they could run Doom.... ~~~~~~ Bait for spammers: root@localhost postmaster@localhost admin@localhost abuse@localhost ] ~~~~~~ Remove "spamless" to email me. |
#8
|
|||
|
|||
Overlord wrote:
On Thu, 22 Apr 2004 21:16:01 -0600, Rob Stow wrote: Noozer wrote: "Overlord" wrote in message ... uh.....lessee....... click RUN type in "cmd" enter type in "DEBUG" enter type in "d c000:0010" enter type in "d" enter a couple times for a couple more screens until you get to the part of the Video BIOS that has the model # you want to see. It should tell you what it is. when you're done, type in "q" enter {for quit} Of course enter is the enter key and the parts in "" are what you type (without the "" quotes. OUCH!! Been doing this a while, eh? Remember how to format an MFM drive in debug? Oh, man. Talk about dredging up nasty memories. I used to be so good at making typos in the worst possible places when using debug - and I remember managing to permanently ruin an MFM drive. It was a 5 MB or 10 MB drive and cost more than I made in a month. But doublespace was great. Almost doubled your storage. You ever find that huge file on that G or H partition and delete it for the space.... and find that was your entire C drive in a single compressed file on a sneaky partition? I forget what the name of the util was before M$ stole it... Stacker by Stac IIRC. Remember using Copy con for cobbling your files and then when they didn't work using Debug or Edlin to troubleshoot 'em? I remember kids bringing me dual 5¼ floppy systems and wanting me to make it so they could run Doom.... ~~~~~~ Bait for spammers: root@localhost postmaster@localhost admin@localhost abuse@localhost ] ~~~~~~ Remove "spamless" to email me. |
#9
|
|||
|
|||
|
#10
|
|||
|
|||
"Sal Amie" wrote in message
... I have this old graphics card which I am trying to identify. It is labelled Sept 1999. The circuit board has a logo on the circuit side which says "graphics by ATI Rage 128" On the components side of the circuit board it says ""C in a circle"" (copyright) 1999 ATI Technologies Inc. (1) Does this mean the board is actually made by ATI or is it probbaly made by someone else using an ATI Rage chip? (I didn't think grahhics chip companies like ATI made complete graphics boards.) (2) Also on the circuit board it says "N625". What does this mean? (3) Another paper label (with a barcode) says R128 GL 32M" but I can't find that on the Web. (4) One of the chips has a paper label saying "R128 66501" Can someone tell me what board this is and which of those bits of info were ther key indentifiers. --- Another question I would like to ask is .... is this graphics card any better than the integrated video on modern boards using the latest integrated graphics chips like the "NVIDIA nForce2 IGP"? (E.G. the Asus AV8NX-VM motherboard) http://www.halfdone.com/Development/UnknownDevices/ |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Made the switch... A7V8X-X to A7N8X... Now my graphics card fan is annoying. | hupjack | Homebuilt PC's | 9 | April 13th 04 10:17 AM |
A graphics card with video capture | Hupjack | Homebuilt PC's | 14 | April 7th 04 09:15 PM |
Inexpensive graphics card for servers and cluster nodes | Oliver Mueller | General | 2 | March 29th 04 10:45 PM |
Problem: Compaq EVO D310 vs Nvidia Graphics Card. | Tomas | General | 5 | November 1st 03 05:39 PM |
Recommend graphics card for this system? | jeffc | Homebuilt PC's | 3 | October 28th 03 11:59 PM |