If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Easy question: cpu clocking on A7V8X-X
I have an A7V8X-X motherboard and a 2700+ athlon xp. My memory is crucial
ddr-400. I'd like to set it at it's rated speed. What should I put in for: CPU Speed CPU Frequency Multiple CPU External Frequency Memory Frequency ? Thanks and sorry for my cluelessness. -- Stephen If your desktop gets out of control easily, you probably have too much stuff on it that doesn't need to be there. Donna Smallin, "Unclutter Your Home" |
#2
|
|||
|
|||
In article ,
se wrote: I have an A7V8X-X motherboard and a 2700+ athlon xp. My memory is crucial ddr-400. I'd like to set it at it's rated speed. What should I put in for: CPU Speed CPU Frequency Multiple CPU External Frequency Memory Frequency ? Thanks and sorry for my cluelessness. http://www.qdi.nl/support/CPUQDISocketA.htm It says 2700+ is 2167MHz and the bus clock is 166MHz. CPU Bus clock * 2 = FSB = FSB333 Memory works best if matched = DDR333 (mem_clock 166MHz * 2 = DDR rate) You can leave it at the defaults of "CPU Speed" [Auto] and "Memory Speed" [Auto], and then check with http://www.cpuid.com/cpuz.php to see whether auto did the right thing. If you want to set the stuff yourself, set CPU Speed to Manual, then look for a CPU External Frequency of [166/33], as 166 is the actual CPU bus clock. The 33 part is the proper value for the PCI bus, and values over 37.5 for PCI aren't recommended. The FSB transfers two pieces of data per clock, so the external frequency of 166 gives the FSB333 value. (Memory works the same way. A 166MHz memory clock transfers two pieces of data per clock, for a DDR333 rate. You have to distinguish between a BIOS entry that is a "clock" versus one that is a "rate", as some new users end up trying settings which are double what the hardware can handle.) The multiplier on a lot of new processors is locked, and in this case your processor is 2167/166 = multiplier 13X. If you try changing it, check CPUZ to see if the change had any effect. If you plan on changing it, there is much more to know about this (overclocking research) than I can state quickly here. Generally, matching the FSB rate to the DDR memory rate works best, as the resync circuit in the Northbridge operates in its most efficient way when they are matched. Running the memory at DDR400 and the FSB333 will net you very little, and on some boards actually runs slower. To win by boosting the memory, the memory would have to go much higher, before the gains would pay off. HTH, Paul |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
F Need some easy cash ? Check this out !! | Blagovest Baychev | General | 0 | May 19th 04 07:07 PM |
V Need some easy cash ? Check this out !! | Blagovest Baychev | General | 0 | May 19th 04 07:07 PM |
p Need some easy cash ? Check this out !! | Blagovest Baychev | Overclocking | 0 | May 19th 04 07:07 PM |
j Need some easy cash ? Check this out !! | Blagovest Baychev | Overclocking | 0 | May 19th 04 07:07 PM |
Memory Question - outcome of exceeding the memory limits of a machine. | John B. | General | 4 | November 4th 03 12:25 PM |