If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
Hi.
Is this error something to worry about quickly (will have to buy a new HDD if it is urgent. but they are expensive due to Thailand's flood )? Date: Sat, 05 Nov 2011 22:58:13 -0700 From: root To: root Subject: SMART error (Usage) detected on host: FooBar This email was generated by the smartd daemon running on: host name: FooBar DNS domain: localdomain NIS domain: (none) The following warning/error was logged by the smartd daemon: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. For details see host's SYSLOG. You can also use the smartctl utility for further investigation. Another email message will be sent in 24 hours if the problem persists. Syslog showed: # cat /var/log/syslog |grep smart Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 58 to 57 Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 35 Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 58 to 57 Nov 5 13:28:09 FooBar smartd[2784]: smartd 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Nov 5 13:28:09 FooBar smartd[2784]: Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Nov 5 13:28:09 FooBar smartd[2784]: Opened configuration file /etc/smartd.conf Nov 5 13:28:09 FooBar smartd[2784]: Drive: DEVICESCAN, implied '-a' Directive on line 21 of file /etc/smartd.conf Nov 5 13:28:09 FooBar smartd[2784]: Configuration file /etc/smartd.conf was parsed, found DEVICESCAN, scanning devices Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda, type changed from 'scsi' to 'sat' Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], opened Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], ST380011A, S/N:4JV5P7LN, FW:8.01, 80.0 GB Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], found in smartd database. Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sda [SAT], is SMART capable. Adding to "monitor" list. Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sda [SAT], state read from /var/lib/smartmontools/smartd.ST380011A-4JV5P7LN.ata.state Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb, type changed from 'scsi' to 'sat' Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], opened Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], QUANTUM FIREBALLP LM15, S/N:183006136328, FW:A35.0700, 15.0 GB Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], found in smartd database. Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sdb [SAT], is SMART capable. Adding to "monitor" list. Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sdb [SAT], state read from /var/lib/smartmontools/smartd.QUANTUM_FIREBALLP_LM15-183006136328.ata.state Nov 5 13:28:11 FooBar smartd[2784]: Monitoring 2 ATA and 0 SCSI devices Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 36 Nov 5 13:28:12 FooBar smartd[2784]: Device: /dev/sda [SAT], state written to /var/lib/smartmontools/smartd.ST380011A-4JV5P7LN.ata.state Nov 5 13:28:12 FooBar smartd[2784]: Device: /dev/sdb [SAT], state written to /var/lib/smartmontools/smartd.QUANTUM_FIREBALLP_LM15-183006136328.ata.state Nov 5 13:28:12 FooBar smartd[2786]: smartd has fork()ed into background mode. New PID=2786. Nov 5 13:28:12 FooBar smartd[2786]: file /var/run/smartd.pid written containing PID 2786 Nov 5 14:28:13 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 34 Nov 5 14:58:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 34 to 36 Nov 5 15:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 37 Nov 5 16:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 37 to 38 Nov 5 16:58:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 38 to 35 Nov 5 17:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 37 Nov 5 18:58:13 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 37 to 38 Nov 5 19:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 38 to 36 Nov 5 20:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 9 Power_On_Hours changed from 44 to 43 Nov 5 20:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 37 Nov 5 22:58:13 FooBar smartd[2786]: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. Nov 5 22:58:13 FooBar smartd[2786]: Sending warning via /usr/share/smartmontools/smartd-runner to root ... Nov 5 22:58:13 FooBar smartd[2786]: Warning via /usr/share/smartmontools/smartd-runner to root: successful Nov 5 22:58:13 FooBar smartd[2786]: Device: /dev/sdb [SAT], SMART Usage Attribute: 9 Power_On_Hours changed from 2 to 1 This timing seems/appears to be related to my earlier reboot (did not power off) of this very old 2005's Debian box due its yesterday's Kernel v2.6.32-5-686 upgrade (not version, just its package with fixes). I had no problems with the reboot (but wasn't looking at its screen though). I ran its detail reports before doing an extended self-test: # smartctl -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Quantum Fireball Plus LM Device Model: QUANTUM FIREBALLP LM15 Serial Number: 183006136328 Firmware Version: A35.0700 User Capacity: 15,020,457,984 bytes [15.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Nov 5 23:05:31 2011 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 46) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 13) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 078 063 020 Pre-fail Always - 2828 4 Start_Stop_Count 0x0032 097 097 008 Old_age Always - 2392 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 001 001 001 Old_age Always FAILING_NOW 64880 10 Spin_Retry_Count 0x0026 100 100 020 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 097 097 008 Old_age Always - 2278 13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 63409 - # 2 Extended offline Completed without error 00% 58068 - # 3 Extended offline Completed without error 00% 54663 - # 4 Extended offline Completed without error 00% 53303 - # 5 Extended offline Completed without error 00% 46603 - # 6 Short offline Completed without error 00% 15067 - # 7 Extended offline Completed without error 00% 13222 - # 8 Short offline Completed without error 00% 13218 - # 9 Short offline Completed without error 00% 8391 - #10 Short offline Completed without error 00% 8391 - Device does not support Selective Self Tests/Logging So I decided to run gsmartcontrol v5.41 (GUI version of smartctl) and it also marked Power_On_Hours as a problem. I ran a long test and it started with loud noises (a fan/motor or something spinning?) for about 30 seconds. That doesn't sound good to me. Anyways, here is the report after the long test which said no errors/problems: # smartctl -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Quantum Fireball Plus LM Device Model: QUANTUM FIREBALLP LM15 Serial Number: 183006136328 Firmware Version: A35.0700 User Capacity: 15,020,457,984 bytes [15.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Nov 5 23:36:57 2011 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 46) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 13) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 078 063 020 Pre-fail Always - 2828 4 Start_Stop_Count 0x0032 097 097 008 Old_age Always - 2392 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 001 001 001 Old_age Always FAILING_NOW 64880 10 Spin_Retry_Count 0x0026 100 100 020 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 097 097 008 Old_age Always - 2278 13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 64880 - # 2 Extended offline Completed without error 00% 63409 - # 3 Extended offline Completed without error 00% 58068 - # 4 Extended offline Completed without error 00% 54663 - # 5 Extended offline Completed without error 00% 53303 - # 6 Extended offline Completed without error 00% 46603 - # 7 Short offline Completed without error 00% 15067 - # 8 Extended offline Completed without error 00% 13222 - # 9 Short offline Completed without error 00% 13218 - #10 Short offline Completed without error 00% 8391 - #11 Short offline Completed without error 00% 8391 - Device does not support Selective Self Tests/Logging Thank you in advance. -- "... Our world is not an ant farm!" --Duncan MacLeod (Highlander Season 3 Finale Part II) /\___/\ Ant @ http://antfarm.ma.cx (Personal Web Site) / /\ /\ \ Ant's Quality Foraged Links: http://aqfl.net | |o o| | \ _ / If crediting, then use Ant nickname and AQFL URL/link. ( ) If e-mailing, then axe ANT from its address if needed. Ant is currently not listening to any songs on this computer. |
#2
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
In comp.sys.ibm.pc.hardware.storage Ant wrote:
Hi. Is this error something to worry about quickly (will have to buy a new HDD if it is urgent. but they are expensive due to Thailand's flood )? Date: Sat, 05 Nov 2011 22:58:13 -0700 From: root To: root Subject: SMART error (Usage) detected on host: FooBar This email was generated by the smartd daemon running on: host name: FooBar DNS domain: localdomain NIS domain: (none) The following warning/error was logged by the smartd daemon: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. For details see host's SYSLOG. You can also use the smartctl utility for further investigation. Another email message will be sent in 24 hours if the problem persists. Don't worry. This means the drive manufacturer thinks it is about time that you buy a new one, but otherwise the drive is fine. This is a pure uptime count that expires when a pre-set usage time is reached. Arno -- Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email: GnuPG: ID: 1E25338F FP: 0C30 5782 9D93 F785 E79C 0296 797F 6B50 1E25 338F ---- Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans |
#3
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
Arno wrote:
In comp.sys.ibm.pc.hardware.storage Ant... wrote: ... Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. For details see host's SYSLOG. You can also use the smartctl utility for further investigation. Another email message will be sent in 24 hours if the problem persists. You can add '-i 9' to the smartd.conf entry for this device to suppress future warning mails. Smartd reported the failed attribute because VALUE = THRESH: ID# ATTRIBUTE_NAME ... VALUE WORST THRESH TYPE ... WHEN_FAILED RAW... .... ..9 Power_On_Hours ... 001 001 001 Old_age FAILING_NOW 64880 Don't worry. This means the drive manufacturer thinks it is about time that you buy a new one, but otherwise the drive is fine. This is a pure uptime count that expires when a pre-set usage time is reached. Yes. Other attributes look good, even after 64880 hours (7+ years) uptime :-) Many recent drives return threshold 0 for Power_On_Hours and all other usage ("Old_age") attributes which means that these would never "fail". Christian |
#4
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
Ant wrote Hi. Lo. Is this error something to worry about quickly Nope, its an ancient drive which is still working fine. (will have to buy a new HDD if it is urgent. but they are expensive due to Thailand's flood )? Thats varied significantly world wide. Mine havent even gone up 10% for some reason, 2TB samsungs and the cheapest 3TB drives around. Date: Sat, 05 Nov 2011 22:58:13 -0700 From: root To: root Subject: SMART error (Usage) detected on host: FooBar This email was generated by the smartd daemon running on: host name: FooBar DNS domain: localdomain NIS domain: (none) The following warning/error was logged by the smartd daemon: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. Thats just a fancy way of saying that its a VERY old drive. Havent seen a fireball in a ****ING long time now. For details see host's SYSLOG. You can also use the smartctl utility for further investigation. Another email message will be sent in 24 hours if the problem persists. Syslog showed: # cat /var/log/syslog |grep smart Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 58 to 57 Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 35 Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 58 to 57 Nov 5 13:28:09 FooBar smartd[2784]: smartd 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Nov 5 13:28:09 FooBar smartd[2784]: Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Nov 5 13:28:09 FooBar smartd[2784]: Opened configuration file /etc/smartd.conf Nov 5 13:28:09 FooBar smartd[2784]: Drive: DEVICESCAN, implied '-a' Directive on line 21 of file /etc/smartd.conf Nov 5 13:28:09 FooBar smartd[2784]: Configuration file /etc/smartd.conf was parsed, found DEVICESCAN, scanning devices Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda, type changed from 'scsi' to 'sat' Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], opened Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], ST380011A, S/N:4JV5P7LN, FW:8.01, 80.0 GB Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], found in smartd database. Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sda [SAT], is SMART capable. Adding to "monitor" list. Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sda [SAT], state read from /var/lib/smartmontools/smartd.ST380011A-4JV5P7LN.ata.state Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb, type changed from 'scsi' to 'sat' Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], opened Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], QUANTUM FIREBALLP LM15, S/N:183006136328, FW:A35.0700, 15.0 GB Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], found in smartd database. Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sdb [SAT], is SMART capable. Adding to "monitor" list. Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sdb [SAT], state read from /var/lib/smartmontools/smartd.QUANTUM_FIREBALLP_LM15-183006136328.ata.state Nov 5 13:28:11 FooBar smartd[2784]: Monitoring 2 ATA and 0 SCSI devices Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 36 Nov 5 13:28:12 FooBar smartd[2784]: Device: /dev/sda [SAT], state written to /var/lib/smartmontools/smartd.ST380011A-4JV5P7LN.ata.state Nov 5 13:28:12 FooBar smartd[2784]: Device: /dev/sdb [SAT], state written to /var/lib/smartmontools/smartd.QUANTUM_FIREBALLP_LM15-183006136328.ata.state Nov 5 13:28:12 FooBar smartd[2786]: smartd has fork()ed into background mode. New PID=2786. Nov 5 13:28:12 FooBar smartd[2786]: file /var/run/smartd.pid written containing PID 2786 Nov 5 14:28:13 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 34 Nov 5 14:58:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 34 to 36 Nov 5 15:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 37 Nov 5 16:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 37 to 38 Nov 5 16:58:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 38 to 35 Nov 5 17:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 37 Nov 5 18:58:13 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 37 to 38 Nov 5 19:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 38 to 36 Nov 5 20:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 9 Power_On_Hours changed from 44 to 43 Nov 5 20:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 37 Nov 5 22:58:13 FooBar smartd[2786]: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. Nov 5 22:58:13 FooBar smartd[2786]: Sending warning via /usr/share/smartmontools/smartd-runner to root ... Nov 5 22:58:13 FooBar smartd[2786]: Warning via /usr/share/smartmontools/smartd-runner to root: successful Nov 5 22:58:13 FooBar smartd[2786]: Device: /dev/sdb [SAT], SMART Usage Attribute: 9 Power_On_Hours changed from 2 to 1 All of that is it just saying those values have changed. No big deal. This timing seems/appears to be related to my earlier reboot (did not power off) of this very old 2005's Debian box due its yesterday's Kernel v2.6.32-5-686 upgrade (not version, just its package with fixes). I had no problems with the reboot (but wasn't looking at its screen though). I dont believe its significant. I ran its detail reports before doing an extended self-test: # smartctl -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Quantum Fireball Plus LM Device Model: QUANTUM FIREBALLP LM15 Serial Number: 183006136328 Firmware Version: A35.0700 User Capacity: 15,020,457,984 bytes [15.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Nov 5 23:05:31 2011 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 46) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 13) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 078 063 020 Pre-fail Always - 2828 4 Start_Stop_Count 0x0032 097 097 008 Old_age Always - 2392 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 001 001 001 Old_age Always FAILING_NOW 64880 10 Spin_Retry_Count 0x0026 100 100 020 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 097 097 008 Old_age Always - 2278 13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 Those are all fine. SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 63409 - # 2 Extended offline Completed without error 00% 58068 - # 3 Extended offline Completed without error 00% 54663 - # 4 Extended offline Completed without error 00% 53303 - # 5 Extended offline Completed without error 00% 46603 - # 6 Short offline Completed without error 00% 15067 - # 7 Extended offline Completed without error 00% 13222 - # 8 Short offline Completed without error 00% 13218 - # 9 Short offline Completed without error 00% 8391 - #10 Short offline Completed without error 00% 8391 - Device does not support Selective Self Tests/Logging So I decided to run gsmartcontrol v5.41 (GUI version of smartctl) and it also marked Power_On_Hours as a problem. Again, its just saying its a VERY old drive, no news. I ran a long test and it started with loud noises (a fan/motor or something spinning?) for about 30 seconds. That doesn't sound good to me. May just be the power supply fan. Anyways, here is the report after the long test which said no errors/problems: # smartctl -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Quantum Fireball Plus LM Device Model: QUANTUM FIREBALLP LM15 Serial Number: 183006136328 Firmware Version: A35.0700 User Capacity: 15,020,457,984 bytes [15.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Nov 5 23:36:57 2011 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 46) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 13) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 078 063 020 Pre-fail Always - 2828 4 Start_Stop_Count 0x0032 097 097 008 Old_age Always - 2392 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 001 001 001 Old_age Always FAILING_NOW 64880 10 Spin_Retry_Count 0x0026 100 100 020 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 097 097 008 Old_age Always - 2278 13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 Again, those are fine. SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 64880 - # 2 Extended offline Completed without error 00% 63409 - # 3 Extended offline Completed without error 00% 58068 - # 4 Extended offline Completed without error 00% 54663 - # 5 Extended offline Completed without error 00% 53303 - # 6 Extended offline Completed without error 00% 46603 - # 7 Short offline Completed without error 00% 15067 - # 8 Extended offline Completed without error 00% 13222 - # 9 Short offline Completed without error 00% 13218 - #10 Short offline Completed without error 00% 8391 - #11 Short offline Completed without error 00% 8391 - Device does not support Selective Self Tests/Logging Thank you in advance. Still smirking. |
#5
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."? (thanks!)
Thanks for the replies! I will ignore that one then. [smirking for
Rod :P] On 11/5/2011 11:39 PM PT, Ant typed: Hi. Is this error something to worry about quickly (will have to buy a new HDD if it is urgent. but they are expensive due to Thailand's flood )? Date: Sat, 05 Nov 2011 22:58:13 -0700 From: root To: root Subject: SMART error (Usage) detected on host: FooBar This email was generated by the smartd daemon running on: host name: FooBar DNS domain: localdomain NIS domain: (none) The following warning/error was logged by the smartd daemon: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. For details see host's SYSLOG. You can also use the smartctl utility for further investigation. Another email message will be sent in 24 hours if the problem persists. Syslog showed: # cat /var/log/syslog |grep smart Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 58 to 57 Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 35 Nov 5 13:04:35 FooBar smartd[2815]: Device: /dev/sda [SAT], SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 58 to 57 Nov 5 13:28:09 FooBar smartd[2784]: smartd 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Nov 5 13:28:09 FooBar smartd[2784]: Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Nov 5 13:28:09 FooBar smartd[2784]: Opened configuration file /etc/smartd.conf Nov 5 13:28:09 FooBar smartd[2784]: Drive: DEVICESCAN, implied '-a' Directive on line 21 of file /etc/smartd.conf Nov 5 13:28:09 FooBar smartd[2784]: Configuration file /etc/smartd.conf was parsed, found DEVICESCAN, scanning devices Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda, type changed from 'scsi' to 'sat' Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], opened Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], ST380011A, S/N:4JV5P7LN, FW:8.01, 80.0 GB Nov 5 13:28:09 FooBar smartd[2784]: Device: /dev/sda [SAT], found in smartd database. Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sda [SAT], is SMART capable. Adding to "monitor" list. Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sda [SAT], state read from /var/lib/smartmontools/smartd.ST380011A-4JV5P7LN.ata.state Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb, type changed from 'scsi' to 'sat' Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], opened Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], QUANTUM FIREBALLP LM15, S/N:183006136328, FW:A35.0700, 15.0 GB Nov 5 13:28:10 FooBar smartd[2784]: Device: /dev/sdb [SAT], found in smartd database. Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sdb [SAT], is SMART capable. Adding to "monitor" list. Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sdb [SAT], state read from /var/lib/smartmontools/smartd.QUANTUM_FIREBALLP_LM15-183006136328.ata.state Nov 5 13:28:11 FooBar smartd[2784]: Monitoring 2 ATA and 0 SCSI devices Nov 5 13:28:11 FooBar smartd[2784]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 36 Nov 5 13:28:12 FooBar smartd[2784]: Device: /dev/sda [SAT], state written to /var/lib/smartmontools/smartd.ST380011A-4JV5P7LN.ata.state Nov 5 13:28:12 FooBar smartd[2784]: Device: /dev/sdb [SAT], state written to /var/lib/smartmontools/smartd.QUANTUM_FIREBALLP_LM15-183006136328.ata.state Nov 5 13:28:12 FooBar smartd[2786]: smartd has fork()ed into background mode. New PID=2786. Nov 5 13:28:12 FooBar smartd[2786]: file /var/run/smartd.pid written containing PID 2786 Nov 5 14:28:13 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 34 Nov 5 14:58:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 34 to 36 Nov 5 15:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 37 Nov 5 16:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 37 to 38 Nov 5 16:58:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 38 to 35 Nov 5 17:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 37 Nov 5 18:58:13 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 37 to 38 Nov 5 19:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 38 to 36 Nov 5 20:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 9 Power_On_Hours changed from 44 to 43 Nov 5 20:28:12 FooBar smartd[2786]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 36 to 37 Nov 5 22:58:13 FooBar smartd[2786]: Device: /dev/sdb [SAT], Failed SMART usage Attribute: 9 Power_On_Hours. Nov 5 22:58:13 FooBar smartd[2786]: Sending warning via /usr/share/smartmontools/smartd-runner to root ... Nov 5 22:58:13 FooBar smartd[2786]: Warning via /usr/share/smartmontools/smartd-runner to root: successful Nov 5 22:58:13 FooBar smartd[2786]: Device: /dev/sdb [SAT], SMART Usage Attribute: 9 Power_On_Hours changed from 2 to 1 This timing seems/appears to be related to my earlier reboot (did not power off) of this very old 2005's Debian box due its yesterday's Kernel v2.6.32-5-686 upgrade (not version, just its package with fixes). I had no problems with the reboot (but wasn't looking at its screen though). I ran its detail reports before doing an extended self-test: # smartctl -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Quantum Fireball Plus LM Device Model: QUANTUM FIREBALLP LM15 Serial Number: 183006136328 Firmware Version: A35.0700 User Capacity: 15,020,457,984 bytes [15.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Nov 5 23:05:31 2011 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 46) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 13) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 078 063 020 Pre-fail Always - 2828 4 Start_Stop_Count 0x0032 097 097 008 Old_age Always - 2392 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 001 001 001 Old_age Always FAILING_NOW 64880 10 Spin_Retry_Count 0x0026 100 100 020 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 097 097 008 Old_age Always - 2278 13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 63409 - # 2 Extended offline Completed without error 00% 58068 - # 3 Extended offline Completed without error 00% 54663 - # 4 Extended offline Completed without error 00% 53303 - # 5 Extended offline Completed without error 00% 46603 - # 6 Short offline Completed without error 00% 15067 - # 7 Extended offline Completed without error 00% 13222 - # 8 Short offline Completed without error 00% 13218 - # 9 Short offline Completed without error 00% 8391 - #10 Short offline Completed without error 00% 8391 - Device does not support Selective Self Tests/Logging So I decided to run gsmartcontrol v5.41 (GUI version of smartctl) and it also marked Power_On_Hours as a problem. I ran a long test and it started with loud noises (a fan/motor or something spinning?) for about 30 seconds. That doesn't sound good to me. Anyways, here is the report after the long test which said no errors/problems: # smartctl -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.32-5-686] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Quantum Fireball Plus LM Device Model: QUANTUM FIREBALLP LM15 Serial Number: 183006136328 Firmware Version: A35.0700 User Capacity: 15,020,457,984 bytes [15.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Nov 5 23:36:57 2011 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 46) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 13) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 078 063 020 Pre-fail Always - 2828 4 Start_Stop_Count 0x0032 097 097 008 Old_age Always - 2392 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 001 001 001 Old_age Always FAILING_NOW 64880 10 Spin_Retry_Count 0x0026 100 100 020 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 097 097 008 Old_age Always - 2278 13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always - 0 199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0010 100 100 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 64880 - # 2 Extended offline Completed without error 00% 63409 - # 3 Extended offline Completed without error 00% 58068 - # 4 Extended offline Completed without error 00% 54663 - # 5 Extended offline Completed without error 00% 53303 - # 6 Extended offline Completed without error 00% 46603 - # 7 Short offline Completed without error 00% 15067 - # 8 Extended offline Completed without error 00% 13222 - # 9 Short offline Completed without error 00% 13218 - #10 Short offline Completed without error 00% 8391 - #11 Short offline Completed without error 00% 8391 - Device does not support Selective Self Tests/Logging Thank you in advance. -- "Look at them, fighting like ants. The fate's waiting them." --Kane in Command & Conquer 3: Tiberium Wars /\___/\ Ant @ http://antfarm.ma.cx (Personal Web Site) / /\ /\ \ Ant's Quality Foraged Links: http://aqfl.net | |o o| | \ _ / If crediting, then use Ant nickname and AQFL URL/link. ( ) If e-mailing, then axe ANT from its address if needed. Ant is/was listening to a song on this computer: RoVeRDude58 - AA - Ilusional Discovery (ID: 454530) |
#6
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
On Sun, 06 Nov 2011 18:54:39 +0100, Christian Franke
put finger to keyboard and composed: Other attributes look good, even after 64880 hours (7+ years) uptime :-) My Fujitsu 20GB HDD exceeded its POH threshold long ago. It still has no reallocated or pending sectors. - Franc Zabkar -- Please remove one 'i' from my address when replying by email. |
#7
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
On 11/06/2011 01:39 AM, Ant wrote:
Hi. Is this error something to worry about quickly (will have to buy a new HDD if it is urgent. but they are expensive due to Thailand's flood )? Date: Sat, 05 Nov 2011 22:58:13 -0700 From: root To: root Subject: SMART error (Usage) detected on host: FooBar Though the drive is apparently still good... it does have a lot of hours on it. I don't know what the flood in Thailand did ...but I just checked NewEgg and you can get a new hard drive for about 100USD or so. I'd consider replacing it...but I don't think you have to rush. OTOH: As long as all your data are backed up and you keep it backed up. no need to worry |
#8
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
On Sunday, November 6th, 2011, at 20:40:38h -0600, Philo advised:
I'd consider replacing it...but I don't think you have to rush. It is usually the belief that prices will rise and the rush to buy that pushes the price up, not the actual shortage. This happened with rice prices in 2008. http://www.npr.ORG/blogs/thesalt/2011/11/02/141771712/how-fear-drove-world-rice-markets-insane |
#9
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
In article , philo wrote:
On 11/06/2011 01:39 AM, Ant wrote: Hi. Is this error something to worry about quickly (will have to buy a new HDD if it is urgent. but they are expensive due to Thailand's flood )? Date: Sat, 05 Nov 2011 22:58:13 -0700 From: root To: root Subject: SMART error (Usage) detected on host: FooBar Though the drive is apparently still good... it does have a lot of hours on it. I don't know what the flood in Thailand did ...but I just checked NewEgg and you can get a new hard drive for about 100USD or so. Yes, but those same hard drives you see for $100 were just $59 weeks ago. I'd consider replacing it...but I don't think you have to rush. OTOH: As long as all your data are backed up and you keep it backed up. no need to worry |
#10
|
|||
|
|||
"Failed SMART usage Attribute: 9 Power_On_Hours."?
On Monday, November 7th, 2011 at 15:26:33h +0000, GMAN wrote:
Yes, but those same hard drives you see for $100 were just $59 weeks ago. Can you blame the multinational corporations for gouging consumers on the artificially inflated prices when they have management bonuses and stockholder dividends to pay? Remember, it is not the material and manufacturing costs which affect so much the final price, but what the market will bear -- ie what walk-in traffic will pay for convenience because they "want it now". |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Acronis 10 and Vista x64: "failed to backup file or folder" "error reading the file" 0x40001 | markm75 | Storage (alternative) | 0 | February 24th 07 04:17 AM |
Change computer date with "smart" chip in HP printers? | Burt | Printers | 2 | January 5th 06 04:23 PM |
Change computer date with "smart" chip in HP printers? | Arthur Entlich | Printers | 0 | January 4th 06 06:09 PM |
Change computer date with "smart" chip in HP printers? | [email protected] | Printers | 0 | January 3rd 06 10:19 PM |
Change computer date with "smart" chip in HP printers? | Bob Headrick | Printers | 0 | December 24th 05 10:23 PM |