If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Problema cpu amd 3000+
Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD
3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide |
#2
|
|||
|
|||
Problema cpu amd 3000+
davide wrote:
Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD 3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide You'll get more help if you post in English. -Dylan C |
#3
|
|||
|
|||
Problema cpu amd 3000+
"davide" wrote in message ... Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD 3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide I have installed this today on my MB asus A7V8X via kt400 processore AMD 3000+ in substitution of the most datatato 2000+. The problem is that after to have received guarantees approximately its compatibility with my MB this evening after a careful and scrupulous "operation" of substitution (uses of termoconduttiva paste), to riavvio the system feeds the impeller of the cpu turns but the PC does not make the boot. I have mistaken something, or is cpu a defective someone it knows to me to help or it has had a similar experience? Thanks for the eventual answers. clear the bios using the jumper and restart so the bios can redetect the cpu speed and multiplier you may still need to reset the correct FSB in the bios via the menu if it does not detect correctly certain wrong settings can cause the system to hang on boot which is what I suspect is happening.. elimini l'essere vivente usando il ponticello ed il riavviamento in modo da il redetect della latta di essere vivente la velocità e moltiplicatore del CPU potete necessità tranquilla di ripristinare il FSB corretto nell'essere vivente via il menu se non rileva correttamente determinate regolazioni può indurre il sistema ad appendere sul caricamento del sistema che è che cosa ritengo sospetto sto accadendo. Derek .. |
#4
|
|||
|
|||
Problema cpu amd 3000+
Thanks for the answer,
but according to you it is normal that the PC after having inserted the CPU 3000+ is not restarted and doesn't make any type of boot? Cleaning the bios I don't risk something? Thanks David "Derek" ha scritto nel messaggio ... "davide" wrote in message ... Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD 3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide I have installed this today on my MB asus A7V8X via kt400 processore AMD 3000+ in substitution of the most datatato 2000+. The problem is that after to have received guarantees approximately its compatibility with my MB this evening after a careful and scrupulous "operation" of substitution (uses of termoconduttiva paste), to riavvio the system feeds the impeller of the cpu turns but the PC does not make the boot. I have mistaken something, or is cpu a defective someone it knows to me to help or it has had a similar experience? Thanks for the eventual answers. clear the bios using the jumper and restart so the bios can redetect the cpu speed and multiplier you may still need to reset the correct FSB in the bios via the menu if it does not detect correctly certain wrong settings can cause the system to hang on boot which is what I suspect is happening.. elimini l'essere vivente usando il ponticello ed il riavviamento in modo da il redetect della latta di essere vivente la velocità e moltiplicatore del CPU potete necessità tranquilla di ripristinare il FSB corretto nell'essere vivente via il menu se non rileva correttamente determinate regolazioni può indurre il sistema ad appendere sul caricamento del sistema che è che cosa ritengo sospetto sto accadendo. Derek . |
#5
|
|||
|
|||
Problema cpu amd 3000+
"davide" wrote in message ... Thanks for the answer, but according to you it is normal that the PC after having inserted the CPU 3000+ is not restarted and doesn't make any type of boot? Cleaning the bios I don't risk something? Thanks David "Derek" ha scritto nel messaggio ... "davide" wrote in message ... Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD 3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide I have installed this today on my MB asus A7V8X via kt400 processore AMD 3000+ in substitution of the most datatato 2000+. The problem is that after to have received guarantees approximately its compatibility with my MB this evening after a careful and scrupulous "operation" of substitution (uses of termoconduttiva paste), to riavvio the system feeds the impeller of the cpu turns but the PC does not make the boot. I have mistaken something, or is cpu a defective someone it knows to me to help or it has had a similar experience? Thanks for the eventual answers. clear the bios using the jumper and restart so the bios can redetect the cpu speed and multiplier you may still need to reset the correct FSB in the bios via the menu if it does not detect correctly certain wrong settings can cause the system to hang on boot which is what I suspect is happening.. elimini l'essere vivente usando il ponticello ed il riavviamento in modo da il redetect della latta di essere vivente la velocità e moltiplicatore del CPU potete necessità tranquilla di ripristinare il FSB corretto nell'essere vivente via il menu se non rileva correttamente determinate regolazioni può indurre il sistema ad appendere sul caricamento del sistema che è che cosa ritengo sospetto sto accadendo. Derek . I have known it happen after an upgrade the mismatch in either the multiplier or FSB can prevent the boot , when you clear the bios (cmos) you will lose settings in the bios which will go to the default settings you will have to reset detect drives etc most is fairly straight forward and covered in the mobo manual but it should get you into a situation where at least the system will start.One other thing to try - you can get the system hanging if the video card is not seated securely AGP boards do this very often when moved while the monitor is still connected Derek |
#6
|
|||
|
|||
Problema cpu amd 3000+
I have tried to reset the cmos to remove the battery and to clean with care
the CPU from the thermal grease, but the problem is not resolved the pc it doesn't set out. Then I have inserted again the my old CPU 2000+ and the system is normally departed after having restored inside the menu bios the original values. Thanks "Derek" ha scritto nel messaggio ... "davide" wrote in message ... Thanks for the answer, but according to you it is normal that the PC after having inserted the CPU 3000+ is not restarted and doesn't make any type of boot? Cleaning the bios I don't risk something? Thanks David "Derek" ha scritto nel messaggio ... "davide" wrote in message ... Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD 3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide I have installed this today on my MB asus A7V8X via kt400 processore AMD 3000+ in substitution of the most datatato 2000+. The problem is that after to have received guarantees approximately its compatibility with my MB this evening after a careful and scrupulous "operation" of substitution (uses of termoconduttiva paste), to riavvio the system feeds the impeller of the cpu turns but the PC does not make the boot. I have mistaken something, or is cpu a defective someone it knows to me to help or it has had a similar experience? Thanks for the eventual answers. clear the bios using the jumper and restart so the bios can redetect the cpu speed and multiplier you may still need to reset the correct FSB in the bios via the menu if it does not detect correctly certain wrong settings can cause the system to hang on boot which is what I suspect is happening.. elimini l'essere vivente usando il ponticello ed il riavviamento in modo da il redetect della latta di essere vivente la velocità e moltiplicatore del CPU potete necessità tranquilla di ripristinare il FSB corretto nell'essere vivente via il menu se non rileva correttamente determinate regolazioni può indurre il sistema ad appendere sul caricamento del sistema che è che cosa ritengo sospetto sto accadendo. Derek . I have known it happen after an upgrade the mismatch in either the multiplier or FSB can prevent the boot , when you clear the bios (cmos) you will lose settings in the bios which will go to the default settings you will have to reset detect drives etc most is fairly straight forward and covered in the mobo manual but it should get you into a situation where at least the system will start.One other thing to try - you can get the system hanging if the video card is not seated securely AGP boards do this very often when moved while the monitor is still connected Derek |
#7
|
|||
|
|||
Problema cpu amd 3000+
davide wrote:
I have tried to reset the cmos to remove the battery and to clean with care the CPU from the thermal grease, but the problem is not resolved the pc it doesn't set out. Then I have inserted again the my old CPU 2000+ and the system is normally departed after having restored inside the menu bios the original values. Thanks "Derek" ha scritto nel messaggio ... "davide" wrote in message .. . Thanks for the answer, but according to you it is normal that the PC after having inserted the CPU 3000+ is not restarted and doesn't make any type of boot? Cleaning the bios I don't risk something? Thanks David "Derek" ha scritto nel messaggio ... "davide" wrote in message ... Ho installato quest'oggi sulla mia MB asus A7V8X via kt400 il processore AMD 3000+ in sostituzione del più datatato 2000+. Il problema è che dopo aver ricevuto garanzie circa la sua compatibilità con la mia MB questa sera dopo un'attenta e scrupolosa "operazione" di sostituzione (utilizzo di pasta termoconduttiva), al riavvio il sistema si alimenta la ventola della cpu gira ma il pc non fa il boot. Ho sbagliato qualcosa, o è una cpu difettosa qualcuno mi sa aiutare o ha avuto un esperienza simile? Grazie per le eventuali risposte. Davide I have installed this today on my MB asus A7V8X via kt400 processore AMD 3000+ in substitution of the most datatato 2000+. The problem is that after to have received guarantees approximately its compatibility with my MB this evening after a careful and scrupulous "operation" of substitution (uses of termoconduttiva paste), to riavvio the system feeds the impeller of the cpu turns but the PC does not make the boot. I have mistaken something, or is cpu a defective someone it knows to me to help or it has had a similar experience? Thanks for the eventual answers. clear the bios using the jumper and restart so the bios can redetect the cpu speed and multiplier you may still need to reset the correct FSB in the bios via the menu if it does not detect correctly certain wrong settings can cause the system to hang on boot which is what I suspect is happening.. elimini l'essere vivente usando il ponticello ed il riavviamento in modo da il redetect della latta di essere vivente la velocità e moltiplicatore del CPU potete necessità tranquilla di ripristinare il FSB corretto nell'essere vivente via il menu se non rileva correttamente determinate regolazioni può indurre il sistema ad appendere sul caricamento del sistema che è che cosa ritengo sospetto sto accadendo. Derek . I have known it happen after an upgrade the mismatch in either the multiplier or FSB can prevent the boot , when you clear the bios (cmos) you will lose settings in the bios which will go to the default settings you will have to reset detect drives etc most is fairly straight forward and covered in the mobo manual but it should get you into a situation where at least the system will start.One other thing to try - you can get the system hanging if the video card is not seated securely AGP boards do this very often when moved while the monitor is still connected Derek If your old CPU still works, its quite possible that the new 3000+ is either incompatible or damaged. Easiest thing to do is try it in a different motherboard. -Dylan C |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Athlon 2800 vs 3000 vs P4 2.66 | JeffLaw | General | 1 | February 29th 04 09:41 PM |
Athlon 2800 vs 3000 vs Intel 2.66? | JeffLaw | Homebuilt PC's | 1 | February 29th 04 09:39 PM |
Athlon 2800 vs 3000 vs P4 2.66 | JeffLaw | General Hardware | 0 | February 29th 04 09:32 PM |
Barton 3000 2.1GHZ or Barton 3000 2.17 GHZ | Max Harrell | Overclocking AMD Processors | 2 | December 29th 03 09:25 PM |
Benchmarking of EVA 3000 and Fast 600 Turbo | Flemming Haurum | Storage & Hardrives | 9 | December 16th 03 05:49 AM |