If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
"calibration area full" CDRW = useless?
I have a CDRW which triggers the "calibration area full" error in Nero
5 consistently, even after a "full format". Obviously all burning attempts also failed (cannot perform end track). The drive is a brand new Gigabyte GO0404 DVD burner, while the CDRW is a relatively new Verbatim 24X CDRW. Does it mean the CDRW is destined for the bin? |
#2
|
|||
|
|||
typed:
I have a CDRW which triggers the "calibration area full" error in Nero 5 consistently, even after a "full format". Obviously all burning attempts also failed (cannot perform end track). The drive is a brand new Gigabyte GO0404 DVD burner, while the CDRW is a relatively new Verbatim 24X CDRW. Does it mean the CDRW is destined for the bin? Did you try with different media? it could be that drive can't calibrate itself succesfully,so it can be dead. |
#3
|
|||
|
|||
Chan WK wrote:
I have a CDRW which triggers the "calibration area full" error in Nero 5 consistently, even after a "full format". Obviously all burning attempts also failed (cannot perform end track). The drive is a brand new Gigabyte GO0404 DVD burner, while the CDRW is a relatively new Verbatim 24X CDRW. Does it mean the CDRW is destined for the bin? 'Calibration area full' means that it could not be read for calibration. In fact, it may have nothing written to it at all, but simply be unreadable. That usually occurs with a severe mismatch of medium to drive. If you've done a full format, then you have prepared your disc for packet writing and that in itself can be the problem. However, you should pick a blank from a major vendor which has the same marking as that on the faceplate logo of your drive: Ultra Speed, High Speed or neither. If that works, then you simply have a badly mismatched disc to trash, not a whole drive. Mike -- http://www.mrichter.com/ |
#4
|
|||
|
|||
"Chan WK" wrote in message
om... I have a CDRW which triggers the "calibration area full" error in Nero 5 consistently, even after a "full format". Obviously all burning attempts also failed (cannot perform end track). The drive is a brand new Gigabyte GO0404 DVD burner, while the CDRW is a relatively new Verbatim 24X CDRW. Does it mean the CDRW is destined for the bin? Odd, since the DVD drive says it is a 24x CD-RW writer. Nonetheless, it may not be compatible with that media. I'd try some older 10x media and see how that works. I have a 52/32/52x CD-RW as well as a dual DVD burner, and it will write my 10x CD-RW discs at 12x, without troubles, and the DVD burner will write them at 10x without troubles. The CD-RW drive can write to 24x CD-RW media without trouble, although I only have 1 piece, but it is unwritable in the DVD since it isnt High Speed media but instead Ultra Speed media. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
my new mobo o/c's great | rockerrock | Overclocking AMD Processors | 9 | June 30th 04 08:17 PM |
CDRW not being detected as pri or sec slave... | Fredericks | Homebuilt PC's | 3 | April 21st 04 04:52 AM |
CDRW not being detected as pri or sec slave... | Fredericks | General | 2 | April 18th 04 10:01 PM |
Power Calibration Area Error | Mattrixx | Cdr | 11 | October 21st 03 12:08 AM |
HP CDRW says Calibration area full | Proto | Cdr | 2 | August 10th 03 09:52 PM |