A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » Cdr
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Burner won't write



 
 
Thread Tools Display Modes
  #11  
Old March 7th 06, 09:21 PM posted to alt.comp.periphs.cdr
external usenet poster
 
Posts: n/a
Default Burner won't write

.. --------------------------------------
Mike Richter, were you born with
"Scam Artist" emblazoned on your face?
--------------------------------------
http://tinyurl.com/6eldj

(No Pipsqueaks have been able to prove ANY of the above is a LIBEL)
( -- despite Mikey claimed to have proof of misquotes !! )
'

wrote:
smh wrote:
Colin Bearfield wrote:

In my time I've installed a few burners and not had any trouble. Now
I've got a friend's PC to fix and I installed his second hand burner.
It would read but it wouldn't write. F

First I tried to burn an image using Acronis True Image v9. It
wouldn't even start.

Then I tried the XP burning software and it went through the motions
but didn't actually burn anything. Same happened with Nero v4.

I bought a new dual layer Liteon and installed it. Same thing. It
only reads.


I've moved a bit closer to the problem now. The Acronis web site says
use InCD to write to the DVD. However, it stresses that the DVD must
be formatted. I've only heard of that in relation to rewriteable
DVD's. I'm not going to use expensive rewriteable for backing up an
image.

Could you post the link to the Acronis article?

The link is:
http://www.acronis.com/homecomputing...ge/faq.html#10

How can I use Acronis True Image Home 9.0 to write images directly to
DVD discs?

My O/S is XP Pro. My packet writer is Nero InCD

Winxp burn function does not support DVD.
Only Nero 5.5.10.20+ properly supports DVD.

The Acronis page says it only supports DVD/RW, not DVD/R, and that only
with packet writing software.

Your solution is get a "Nero 6 oem suite 3". Think you can get it for
about $10

I am much obliged. Actually I am helping a friend with two computers
and I'm sure that I installed v6 on the other computer.

Double check that. You wrote: "Same happened with Nero v4."

Will do. I think I got that wrong.

On the other hand I think the Liteon drive came with Nero 6.6 OEM.
Should that do as well because it isn't working.

It should. Now you are back to square one. Uninstall Acronis, and run
Nero Clean Tool to uninstall Nero and InCD:
http://ww2.nero.com/nero6/enu/General_CleanTool.html

Disable IMAPI:
Control Panel, Administrative Tools, Services, double-click "IMAPI CD
Burning", click Stop, then set "Startup type" as "Disabled".

Power down and check:

If the old drive is jumpered as CS (cable select), use CS for the burner
instead of Master or Slave. Double check the data cables are
seated/connected properly.

Go into the BIOS and check that the drives are recognized. Check the
drives are working properly in Device Manager.

Reinstall only Nero and try burn.

If I just download InCD from the Nero site do you think that would get
me out of this mess.

No.

Thanks for coming back to me. Tomorrow morning I shall go to my
friends house and thoroughly check everything as you said.

Not sure what you mean by "old drive". I'm now only dealing with the
new Liteon.


Sorry, I was confused.

Again, double check cable connection and jumper settings. If still
trouble, and if the burner is the only cd drive, try swapping Master and
CS jumper settings. If two cd drives, swap them.


We had a successful burn. Here's what happened.

I backed up an image across the network.

I uninstalled True Image.

I downloaded CleanTool and used it to uninstall nero.

I disabled IMAPI. First it declared service status as "stopped". I
changed it to "Disabled".

The IDE cables were bothnew and 80 pin type. The drive was the only
one on the secondary channel and it was jumpered as master. I changed
it to C/S.

In BIOS the drive was recognised as slave.


Seems your only trouble is simply that the drive was jumpered as Master,
but connected as Slave. When you have only one drive, you connect the
drive to the end connector, not the middle one. The BIOS should
recognize it as Master.

Check:
Device Manager, IDE ATA/ATAPI controllers, Primary/Secondary IDE
Channel, Advanced Settings tab. Check that Current Transfer Mode is
UDMA2 or 4.

Once you do the above, sounds like you are ready to go, like installing
InCD and True Image.

(Remember, however, that InCD and True Image burn only to DVD/RW. For
DVD/R, use Nero.)


I forgot to check that the drivers were ok.

I installed Nero 6.6 for rewritable DVD's (not very sure about what
these precisely are).

I ran Nero and compiled 3 or 4 folders from Windows to burn. I chose
verify after burning.

It looked ok and the data seemed to be on the disk when I checked.

Should ve now install InCD and True Image? Will it burn an image to a
DVD?

Many thanks

Colin


You are welcome, and happy burning.
  #12  
Old March 7th 06, 11:56 PM posted to alt.comp.periphs.cdr
external usenet poster
 
Posts: n/a
Default Burner won't write

On Tue, 07 Mar 2006 13:21:19 -0700, smh wrote:

. --------------------------------------
Mike Richter, were you born with
"Scam Artist" emblazoned on your face?
--------------------------------------
http://tinyurl.com/6eldj

(No Pipsqueaks have been able to prove ANY of the above is a LIBEL)
( -- despite Mikey claimed to have proof of misquotes !! )
'

wrote:
smh wrote:
Colin Bearfield wrote:

In my time I've installed a few burners and not had any trouble. Now
I've got a friend's PC to fix and I installed his second hand burner.
It would read but it wouldn't write. F

First I tried to burn an image using Acronis True Image v9. It
wouldn't even start.

Then I tried the XP burning software and it went through the motions
but didn't actually burn anything. Same happened with Nero v4.

I bought a new dual layer Liteon and installed it. Same thing. It
only reads.


I've moved a bit closer to the problem now. The Acronis web site says
use InCD to write to the DVD. However, it stresses that the DVD must
be formatted. I've only heard of that in relation to rewriteable
DVD's. I'm not going to use expensive rewriteable for backing up an
image.

Could you post the link to the Acronis article?

The link is:
http://www.acronis.com/homecomputing...ge/faq.html#10

How can I use Acronis True Image Home 9.0 to write images directly to
DVD discs?

My O/S is XP Pro. My packet writer is Nero InCD

Winxp burn function does not support DVD.
Only Nero 5.5.10.20+ properly supports DVD.

The Acronis page says it only supports DVD/RW, not DVD/R, and that only
with packet writing software.

Your solution is get a "Nero 6 oem suite 3". Think you can get it for
about $10

I am much obliged. Actually I am helping a friend with two computers
and I'm sure that I installed v6 on the other computer.

Double check that. You wrote: "Same happened with Nero v4."

Will do. I think I got that wrong.

On the other hand I think the Liteon drive came with Nero 6.6 OEM.
Should that do as well because it isn't working.

It should. Now you are back to square one. Uninstall Acronis, and run
Nero Clean Tool to uninstall Nero and InCD:
http://ww2.nero.com/nero6/enu/General_CleanTool.html

Disable IMAPI:
Control Panel, Administrative Tools, Services, double-click "IMAPI CD
Burning", click Stop, then set "Startup type" as "Disabled".

Power down and check:

If the old drive is jumpered as CS (cable select), use CS for the burner
instead of Master or Slave. Double check the data cables are
seated/connected properly.

Go into the BIOS and check that the drives are recognized. Check the
drives are working properly in Device Manager.

Reinstall only Nero and try burn.

If I just download InCD from the Nero site do you think that would get
me out of this mess.

No.

Thanks for coming back to me. Tomorrow morning I shall go to my
friends house and thoroughly check everything as you said.

Not sure what you mean by "old drive". I'm now only dealing with the
new Liteon.

Sorry, I was confused.

Again, double check cable connection and jumper settings. If still
trouble, and if the burner is the only cd drive, try swapping Master and
CS jumper settings. If two cd drives, swap them.


We had a successful burn. Here's what happened.

I backed up an image across the network.

I uninstalled True Image.

I downloaded CleanTool and used it to uninstall nero.

I disabled IMAPI. First it declared service status as "stopped". I
changed it to "Disabled".

The IDE cables were bothnew and 80 pin type. The drive was the only
one on the secondary channel and it was jumpered as master. I changed
it to C/S.

In BIOS the drive was recognised as slave.


Seems your only trouble is simply that the drive was jumpered as Master,
but connected as Slave. When you have only one drive, you connect the
drive to the end connector, not the middle one. The BIOS should
recognize it as Master.

Check:
Device Manager, IDE ATA/ATAPI controllers, Primary/Secondary IDE
Channel, Advanced Settings tab. Check that Current Transfer Mode is
UDMA2 or 4.

Once you do the above, sounds like you are ready to go, like installing
InCD and True Image.

(Remember, however, that InCD and True Image burn only to DVD/RW. For
DVD/R, use Nero.)


I forgot to check that the drivers were ok.

I installed Nero 6.6 for rewritable DVD's (not very sure about what
these precisely are).

I ran Nero and compiled 3 or 4 folders from Windows to burn. I chose
verify after burning.

It looked ok and the data seemed to be on the disk when I checked.

Should ve now install InCD and True Image? Will it burn an image to a
DVD?

Many thanks

Colin


You are welcome, and happy burning.


Many thanks.

What does DVD R/W actually mean? My ISP#s web server has gone down or
I'd look for myself.

Colin

PS When it was jumpered as master the BIOS recognised it as master.
It recognised it as slave only after I changed the jumper to C/S.

  #13  
Old March 8th 06, 01:05 AM posted to alt.comp.periphs.cdr
external usenet poster
 
Posts: n/a
Default Burner won't write

.. --------------------------------------
Mike Richter, were you born with
"Scam Artist" emblazoned on your face?
--------------------------------------
http://tinyurl.com/6eldj

(No Pipsqueaks have been able to prove ANY of the above is a LIBEL)
( -- despite Mikey claimed to have proof of misquotes !! )
'

Colin Bearfield wrote:
smh wrote:
wrote:

In my time I've installed a few burners and not had any trouble. Now
I've got a friend's PC to fix and I installed his second hand burner.
It would read but it wouldn't write. F

First I tried to burn an image using Acronis True Image v9. It
wouldn't even start.

Then I tried the XP burning software and it went through the motions
but didn't actually burn anything. Same happened with Nero v4.

I bought a new dual layer Liteon and installed it. Same thing. It
only reads.


I've moved a bit closer to the problem now. The Acronis web site says
use InCD to write to the DVD. However, it stresses that the DVD must
be formatted. I've only heard of that in relation to rewriteable
DVD's. I'm not going to use expensive rewriteable for backing up an
image.

Could you post the link to the Acronis article?

The link is:
http://www.acronis.com/homecomputing...ge/faq.html#10

How can I use Acronis True Image Home 9.0 to write images directly to
DVD discs?

My O/S is XP Pro. My packet writer is Nero InCD

Winxp burn function does not support DVD.
Only Nero 5.5.10.20+ properly supports DVD.

The Acronis page says it only supports DVD/RW, not DVD/R, and that only
with packet writing software.

Your solution is get a "Nero 6 oem suite 3". Think you can get it for
about $10

I am much obliged. Actually I am helping a friend with two computers
and I'm sure that I installed v6 on the other computer.

Double check that. You wrote: "Same happened with Nero v4."

Will do. I think I got that wrong.

On the other hand I think the Liteon drive came with Nero 6.6 OEM.
Should that do as well because it isn't working.

It should. Now you are back to square one. Uninstall Acronis, and run
Nero Clean Tool to uninstall Nero and InCD:
http://ww2.nero.com/nero6/enu/General_CleanTool.html

Disable IMAPI:
Control Panel, Administrative Tools, Services, double-click "IMAPI CD
Burning", click Stop, then set "Startup type" as "Disabled".

Power down and check:

If the old drive is jumpered as CS (cable select), use CS for the burner
instead of Master or Slave. Double check the data cables are
seated/connected properly.

Go into the BIOS and check that the drives are recognized. Check the
drives are working properly in Device Manager.

Reinstall only Nero and try burn.

If I just download InCD from the Nero site do you think that would get
me out of this mess.

No.

Thanks for coming back to me. Tomorrow morning I shall go to my
friends house and thoroughly check everything as you said.

Not sure what you mean by "old drive". I'm now only dealing with the
new Liteon.

Sorry, I was confused.

Again, double check cable connection and jumper settings. If still
trouble, and if the burner is the only cd drive, try swapping Master and
CS jumper settings. If two cd drives, swap them.

We had a successful burn. Here's what happened.

I backed up an image across the network.

I uninstalled True Image.

I downloaded CleanTool and used it to uninstall nero.

I disabled IMAPI. First it declared service status as "stopped". I
changed it to "Disabled".

The IDE cables were bothnew and 80 pin type. The drive was the only
one on the secondary channel and it was jumpered as master. I changed
it to C/S.

In BIOS the drive was recognised as slave.


Seems your only trouble is simply that the drive was jumpered as Master,
but connected as Slave. When you have only one drive, you connect the
drive to the end connector, not the middle one. The BIOS should
recognize it as Master.

Check:
Device Manager, IDE ATA/ATAPI controllers, Primary/Secondary IDE
Channel, Advanced Settings tab. Check that Current Transfer Mode is
UDMA2 or 4.

Once you do the above, sounds like you are ready to go, like installing
InCD and True Image.

(Remember, however, that InCD and True Image burn only to DVD/RW. For
DVD/R, use Nero.)


I forgot to check that the drivers were ok.

I installed Nero 6.6 for rewritable DVD's (not very sure about what
these precisely are).

I ran Nero and compiled 3 or 4 folders from Windows to burn. I chose
verify after burning.

It looked ok and the data seemed to be on the disk when I checked.

Should ve now install InCD and True Image? Will it burn an image to a
DVD?

Many thanks

Colin


You are welcome, and happy burning.


Many thanks.

What does DVD R/W actually mean? My ISP#s web server has gone down or
I'd look for myself.


"DVD/RW" was meant to mean both dvd-RW and dvd+RW. Maybe should go back
to using "DVD_RW" to mean both -rw and +rw. And similary for "DVD/R" to
mean dvd+R and dvd-R, and again go back to using "DVD_R" to mean both -r
and +r.

PS When it was jumpered as master the BIOS recognised it as master.
It recognised it as slave only after I changed the jumper to C/S.


The BIOS must be checking the drive's jumper setting first and stop
checking further once Master or Slave is "settled". Thanks for the tip.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Enable write cache on scsi disc drive Christian Marx Storage (alternative) 2 September 1st 04 11:17 PM
FastT200 write performance problem Emmanuel Bouchard Storage (alternative) 0 September 1st 04 04:44 AM
Help with DVD Burner mark Homebuilt PC's 1 June 6th 04 06:26 PM
Help!! My Burner Can't Read Any Disks (Blank or Recorded) , Is it Dying On Me. Neemo Cdr 0 July 30th 03 05:57 AM
Help!! My Burner Can't Read Any Disks (Blank or Recorded) , Is it Dying On Me. Neemo Cdr 1 July 29th 03 03:52 PM


All times are GMT +1. The time now is 02:20 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.