Motherboard installation in Evercase 4252

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to use
some I have from another installation, the board is raised to high for
the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for your help!

Jeesh I had to look at your sig to see if you were 'leigon'

We were just discussing this 1 day or so back. People are saying, 'on
the dimple'. And as you said. the backplate doesn't line up with
standoffs. So it looks that way. No instructions on the install of the
mainboard? I mean, this is a change on technology, there should be a
insert or something. I still say those 'mounds' are way wider than a
standoff. or is it that the threaded hole is raised off the mounds
top. Frys didn't have any that were that style, as I was glancing
through their assortment today.

"BoyatHeart" wrote in message
...
First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to
use
some I have from another installation, the board is raised to high
for
the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for
your help!

Hi JAD, The case instructions don't cover mounting the motherboard. The
company web site has no further info. The mounds are wider than
standoffs, but don't appear to contact anything sensitive on the
motherboard. I think it will be alright, but I feel butterflies.

JAD wrote:

Jeesh I had to look at your sig to see if you were 'leigon'

We were just discussing this 1 day or so back. People are saying, 'on
the dimple'. And as you said. the backplate doesn't line up with
standoffs. So it looks that way. No instructions on the install of the
mainboard? I mean, this is a change on technology, there should be a
insert or something. I still say those 'mounds' are way wider than a
standoff. or is it that the threaded hole is raised off the mounds
top. Frys didn't have any that were that style, as I was glancing
through their assortment today.

"BoyatHeart" wrote in message
...

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to

use

some I have from another installation, the board is raised to high

for

the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for

your help!

BoyatHeart wrote:

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to use
some I have from another installation, the board is raised to high for
the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for your
help!

That's the way mine works. Just screw it down.

JAD wrote:

Jeesh I had to look at your sig to see if you were 'leigon'

We were just discussing this 1 day or so back. People are saying, 'on
the dimple'. And as you said. the backplate doesn't line up with
standoffs. So it looks that way. No instructions on the install of the
mainboard? I mean, this is a change on technology, there should be a
insert or something. I still say those 'mounds' are way wider than a
standoff.

They are, at the bottom where it doesn't matter.

or is it that the threaded hole is raised off the mounds
top.

It is on mine.

Frys didn't have any that were that style, as I was glancing
through their assortment today.

"BoyatHeart" wrote in message
...

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to

use

some I have from another installation, the board is raised to high

for

the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for

your help!

Cut card washers for under the board?

Mo..


"BoyatHeart" wrote in message
.. .
Hi JAD, The case instructions don't cover mounting the motherboard. The
company web site has no further info. The mounds are wider than
standoffs, but don't appear to contact anything sensitive on the
motherboard. I think it will be alright, but I feel butterflies.

JAD wrote:

Jeesh I had to look at your sig to see if you were 'leigon'

We were just discussing this 1 day or so back. People are saying, 'on
the dimple'. And as you said. the backplate doesn't line up with
standoffs. So it looks that way. No instructions on the install of the
mainboard? I mean, this is a change on technology, there should be a
insert or something. I still say those 'mounds' are way wider than a
standoff. or is it that the threaded hole is raised off the mounds
top. Frys didn't have any that were that style, as I was glancing
through their assortment today.

"BoyatHeart" wrote in message
...

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to

use

some I have from another installation, the board is raised to high

for

the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for

your help!

"BoyatHeart" wrote in message
...
First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to use some
I have from another installation, the board is raised to high for the
connections to fit at the back. Does this mean I install the motherboard
on the raised dimples, without standoffs? Thanks for your help!

I find these motherboard trays with dimples a little worrisome to me.
I've had plenty of times where I had to change the position of the
standoffs, and also remove some because the motherboard's screw holes were
not lined up as usual. What worries me about these trays with dimples is
there would be no way to change the position of them, and if one is in a
position where there is no mounting hole on the motherboard it would then
short the board.

Are you guys sure that these trays are not meant to have standoffs screwed
into these so called "dimples"? I would still use standoffs, but I really
would want to see one of these cases for myself.
I would also try to avoid buying cases such as these for reasons I've
described.

Martin wrote:

"BoyatHeart" wrote in message
...

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to use some
I have from another installation, the board is raised to high for the
connections to fit at the back. Does this mean I install the motherboard
on the raised dimples, without standoffs? Thanks for your help!


I find these motherboard trays with dimples a little worrisome to me.
I've had plenty of times where I had to change the position of the
standoffs, and also remove some because the motherboard's screw holes were
not lined up as usual. What worries me about these trays with dimples is
there would be no way to change the position of them, and if one is in a
position where there is no mounting hole on the motherboard it would then
short the board.

On mine the stamped 'dimples' are located on *The Standard* ATX hole
pattern and if a motherboard did not have matching holes in those locations
it would NOT be in compliance with ATX.

In addition there are 3, 'on the flat' (as you expect them all to be),
threaded standoff mounting holes for (the PCI edge of) mATX (and whatever).

I do note that I have cases using all 'on the flat' screw in standoffs that
have more holes than this one. What those 'extra' holes are for I don't
know, for sure (perhaps AT, Baby AT, or some variation), but they are not
part of the standard ATX hole pattern.

One could say that when this case says it's an "ATX Case" it means it, and
doesn't have a bevy of 'extra' holes for whatever those 'extra' holes would
be for; nor could you mount something not in compliance with the ATX hole
pattern.

It's possible that you had a motherboard with 'extra' holes, in case it was
going to be put in 'one of those' kind of (non ATX) cases, and your case
tray had 'extra' mounting holes, in case you wanted to mount 'one of those'
kind of (non ATX) motherboards that use them, so that the combination of
the two having the 'extra' hole (for compatibility with 'one of those'
whatevers) led you to use them; and then the next motherboard had only the
standard ATX hole pattern, which would necessitate removing the 'extra'
standoffs.

Are you guys sure that these trays are not meant to have standoffs screwed
into these so called "dimples"? I would still use standoffs,

It won't align with anything (like the rear I/O plate) if you raise it
another 1/4 inch with standoffs screwed into the already 1/4 inch high
'dimples'.


but I really
would want to see one of these cases for myself.
I would also try to avoid buying cases such as these for reasons I've
described.

On Tue, 16 Nov 2004 21:23:16 -0600, BoyatHeart wrote:

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to use
some I have from another installation, the board is raised to high for
the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for your help!

Yes, install on the dimples. I've used about 5 of these cases, they work
just fine for ATX and mATX. You can use standoffs at any hole locations
that don't have corresponding dimples.

Andy

In article , BoyatHeart says...

First time I have used a case that has raised dimples where the
motherboard mounts. No brass standoffs are included. If I were to use
some I have from another installation, the board is raised to high for
the connections to fit at the back. Does this mean I install the
motherboard on the raised dimples, without standoffs? Thanks for your help!


I had to laugh a little at this post since I used this case for my first build
and I had the same worry.

I don't remember if it was in this group but someone suggested using electrical
tape over the nipples and then, when the board is lined up, use an ice pick to
clear the holes. I did it and it worked fine. It's been running like a top for
over 2 years.

I never used this case again but I did add a window panel after the build which
I bought on Newegg for a ridiculously low price. I have built 14 computers
since in various cases but I still love that little Evercase. I just like
building with different cases or I would have used it again, it's a fine case to
work with.

BTW, Evercase has very responsive support.

Ed