If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
cad
Can anyone tell me what they think would be a good AMD processor for AutoCAD
& solidworks applications? Thanks. Rudy |
#2
|
|||
|
|||
cad
* Rudy:
Can anyone tell me what they think would be a good AMD processor for AutoCAD & solidworks applications? Thanks. Probably any as CAD generally doesn't require a beefy CPU (and you didn't tell us of what complexity the projects that should be done on the computer are, so I'm assuming light to normal complexity here). More important is the gfx hardware, though. However, if it's for business use and not just a hobby you definitely don't want to build yourself but get a certified workstation from one of the big vendors (i.e. HP, Dell, Lenovo) instead. There are also models with AMD (i.e. HP xw4550) if you prefer them for some reason. They don't really cost more than a self build system but provide you with proper hardware support and usually are a requirement if you need support for your CAD package from the ISV as well. Benjamin |
#3
|
|||
|
|||
cad
Benjamin Gawert writes:
However, if it's for business use and not just a hobby you definitely don't want to build yourself but get a certified workstation from one of the big vendors (i.e. HP, Dell, Lenovo) instead. ... They don't really cost more than a self build system but provide you with proper hardware support and usually are a requirement if you need support for your CAD package from the ISV as well. I've never owned anything from dell or hp, but I've been quite amazed at the awful component choices in the "big vendor" PCs I've looked at. I suppose a business usually prefers accountability over value though. -Miles -- Infancy, n. The period of our lives when, according to Wordsworth, 'Heaven lies about us.' The world begins lying about us pretty soon afterward. |
#4
|
|||
|
|||
cad
* Miles Bader:
I've never owned anything from dell or hp, I did (quite a lot of different systems) and still do. but I've been quite amazed at the awful component choices in the "big vendor" PCs I've looked at. Really I can't see where the "awful choices" should be. But then you probably shouldn't look at their consumer PCs. I suppose a business usually prefers accountability over value though. No, businesses do prefer value for money. But they usually don't see value in acrylic fans with blue LED lighting, or overclocker stuff in the BIOS. Business users see value in reliability, certifications, remote management capabilities, support and product consistency. Self-building is a nice hobby but as soon as you start to make money with your computer you usually can't afford all the hazzle that comes with DIY. Also for me personally the value of self-built PCs made of generic off-the-shelf components is around zero, basically for the same reasons. Ben |
#5
|
|||
|
|||
cad
Thanks for your comments. I built my system about four years ago. It
consists of an Athlon XP 3200+, Gigabyte Mobo, Quadro FX 3000 video card & 2 gig of DDR 3200/400 ram and WD raptor 10,000 rpm sata's. It is running quite well but the video card is acting up. My problem is the card is an AGP and they are now very hard to find. I want to go with PCIe X16. All I want to do is switch out the Mobo, get a newer CPU and some DDR2 ram. I've been building my own units for years and have no problems with that. I don't use generic components I stick with name brands. I'm not fond of the proprietary stuff or the support that's offered from Dell and others. Thanks again. Rudy "Rudy" wrote in message . .. Can anyone tell me what they think would be a good AMD processor for AutoCAD & solidworks applications? Thanks. Rudy |
Thread Tools | |
Display Modes | |
|
|