If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
Can high voltage from power supply damage harddrive?
In comp.sys.ibm.pc.hardware.storage DevilsPGD wrote:
In message JD was claimed to have wrote: Was a surge protector used for this computer? If not, the user was a fool. Electric supplies are always oscillating up and down and need taming by the surge protector. Surge protectors really aren't needed for modern computers, the PSU should have far more capable surge protection built-in as part of it's design. Ok, sorry, have to go into lecture mode here... Depends on your situation. If you have outdated above-ground mains lines, a high-powered surge-protector is a good idea. The one in the PSU will protect the PSU, but likely die in the process. The problem here is that they are typically too small to survive a surge and typically are not thermally moniroted. So there is a fuse in addition (whcih you should _not_ replace, unless you replace the varistor that does the surge prtection as well!), that blows on a surge. The thing is that varistoirs start to leak current after surges and start to heat up. This can cause fires and make them ineffective as protection. If you have a good quality external surge protector (i.e. one with thermal and functional monitoring), it will also die after a few surges, but it will a) signal this and b) interupt mains voltage via thermal fuses c) have replacable normal fuses d) have varistors that can take several surges before starting to leak enough to need replacement You can then replace the surge protector instead of the PSU or even only the varistor module in some models. More often than not a surge protector won't catch a surge in time anyway, Both gas-arc type and varistor type surge protectioon has basically no reaction time. They do have a minimal activation voltage and lower quelity electronics may get damaged before that voltage is reached. although it will usually do a decent enough job of preventing a fire if some connected device shorts out. That is what fues are for. A surge protector does not hekp here. Arno -- Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email: GnuPG: ID: 1E25338F FP: 0C30 5782 9D93 F785 E79C 0296 797F 6B50 1E25 338F ---- Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans |
#22
|
|||
|
|||
Can high voltage from power supply damage harddrive?
In comp.sys.ibm.pc.hardware.storage mm wrote:
On 29 Aug 2010 01:49:59 GMT, Arno wrote: In comp.sys.ibm.pc.hardware.storage mm wrote: I just talked to my friend who gave me the Dell computer, and he said that his repair guy told him the reason his harddrive failed may (likely?) have been a surge or something coming from the power supply. Is this a cause of harddrive failure? Yes, but only with a cheap PSU that does not have overvoltage and surge protection. There, basically anything is possible, including the PSU killing a drive/computer without a mains surge, just by running amok. A common cause? Cheap PSU: Moderately, especially with above-ground mains lines and a lightening strike. New York City, East 57th St. No telephone poles for miles. Everything from the power substation up to the building is below ground. Everything to the power substation also. Good. Very low surge risk there. 11th story of his apartment building -- Is that good or bad? -- but the mains are in the center of the building, near the elevators -- Does that help? (His building has the same elevator motors and relays that were put in when the building was new, around 1935 iirc. They are beautiful.) Should not matter at all. The building has lightening protection which also protects the power lines within. I imagine that in New York these are inspected regularly, as you reliably get building fires on lightening stikes if they do not work. Sode note: Yes, classic more expensive electical installation ccan be quite beautiful and work for a long, long time. Quality PSU: Very, very unlikely. Quality PSUs are known to occasionally fail on mains surges, but do not produce voltage spikes on the computer side. They also will switch themselves off reliably before killing components if their regulator circuitry fails. Dell has been known to use cheaper compontnts, but not that cheap IMO. Also take into account that a HDD has about a 5% per year (!) failure rate without any outside influence. A conceivable cause but really a guess by the repairman. Indeed. And if that happens, it typically takes the PSU with it. Well, it still works so far, but it has little load, only the mobo and the video card. Oh, I said that. Then I would rule out the PSU as cause. More likely the disk died by itself. FWIW, the repairman sent the HD somewhere to get the data off, but it was too dead or something to do that, and now they want 1500 to 3500 dollars to do it the hard way. Reasonable. But there are a lot of disreputable data-recovery outfits out there, "somewhere" is not enough to advise on whether they are crooks or not. He's trusting his repairman. Where he got him I don't know, but because his wife insisted on living in NY instead of Brooklyn, he lives in an expensive building. Of course everything on the East Side north of 23rd or 42nd is expensive, and I don't know if he got the referral from his neighbors (who have more money than he does) and of course rich people get ripped off too. Trust does not imply competence om the target. Sorry. Although the price-quote is in range of hwat you would get form a reputable company like Kroll-Ontrak. FWIW, the mobo still seems good, although w/o the harddrive, it just displays a few lines and displays a one-line message about no SATA drive, press f2 to do this, f4 to do that. Entirely reasonable. Could I turn on the computer and connect a voltmeter to the hardrive power connector** and watch the needle for a few hours (while I do other things), or do I have to watch for weeks to get a good idea? You would need to use a PSU analyzer set-up to be sure. Expensive and needs considerable knowledge to operate. Well, forget that. Indeed ;-) I would check the +5V lines (red) and +12V lines (yellow) and if they have good voltages (+/- 3% of nominal or so) go for it. If you are afraid of killing more drives, get a new PSU from a reputable manufaturer (I recommend Enermax, by far the best quality). But be carefult, DELL cases sometimes do not take standard PSUs. Ugh. But I'll do my best to measure. And I'll see what Dell sells, or what is sold in Dell's name, for this model if possible. **Or do another connector on the same power supply, since the SATA power connector looks very small? Other connector on the same wires is best. Direct measurements on SATA power connectors are not a good idea, to easy to shorten somethig out. Yeah. I think there are other connectors on the same wire. There should be. Arno -- Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email: GnuPG: ID: 1E25338F FP: 0C30 5782 9D93 F785 E79C 0296 797F 6B50 1E25 338F ---- Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans |
#23
|
|||
|
|||
Can high voltage from power supply damage harddrive?
In comp.sys.ibm.pc.hardware.storage Ant wrote:
On 8/28/2010 11:03 PM PT, Rod Speed typed: I just talked to my friend who gave me the Dell computer, and he said that his repair guy told him the reason his harddrive failed may (likely?) have been a surge or something coming from the power supply. Is this a cause of harddrive failure? Yes, it can happen. A common cause? Nope. It has happened to me back in summer of 2005 with an old ASUS A7V333 motherboard/mobo. (lock ups and no more boot ups) and Quantum Fireball Plus 30 GB IDE HDD (circuit controller died). They were damaged by a recent PSU melt down. The mobo's circuit board had brown/orange coloring on its circuit board, a horrible burning odor/smell, etc. The old HDD also went dead too. I never bothered to recover that drive's datas since I had a backup. It is possible, but it requires a) the PSU regulator failing into overvoltage and b) no output-overvoltage protection. Both failing is very rare, hovever cheap PSUs often come without the protection circuitry. Reason: Price. Let me give you an idea (say 400W): - ElCheapo : $20 - Mid-range : $80 - Enermax with all protection: $120 - Industrial with 10 year lifetime: $300-$500 Now, at the lower end, using cheaper components alone does not cut it anymore, you have to use a lot less components. That means cutting out protection circuirty, using cheaper, less reliable regulators, cheaper transformers with lower insulation rating, etc.. Also your ElCheapo 400W unit is more likely a 250-300W unit, while a 400W Enermax is more likely 500-700W. Arno -- Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email: GnuPG: ID: 1E25338F FP: 0C30 5782 9D93 F785 E79C 0296 797F 6B50 1E25 338F ---- Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans |
#24
|
|||
|
|||
Can high voltage from power supply damage harddrive?
In comp.sys.ibm.pc.hardware.storage Franc Zabkar wrote:
On Sat, 28 Aug 2010 20:49:19 -0400, mm put finger to keyboard and composed: I just talked to my friend who gave me the Dell computer, and he said that his repair guy told him the reason his harddrive failed may (likely?) have been a surge or something coming from the power supply. Is this a cause of harddrive failure? A common cause? Yes, it is a very common cause, especially in external enclosures where people apply a 19V - 20V laptop power adapter in place of the original 12V supply. That is one reason laptops have non-standard power connecctors today. Though my old Sony Vaio Brick (16.5V) vopuld fit. Sony computer engineering sucks badly... In most cases there is an easy no-cost DIY fix. It involves using a pair of flush cutters to remove a shorted TVS (transient voltage suppression) diode. That is stupid. It is there for a reason. You always need to repair protection circuitry, not just remove it. Otherwise you end up like the Deepwhater Horizon. These articles should help you identify the various components: HDD from inside Main parts: http://hddscan.com/doc/HDD_from_inside.html WD Pc easy Faultdiagnostic troubleshooting must try it ... http://forum.hddguru.com/easy-faultd...ry-t12319.html My notes may also help: http://www.users.on.net/~fzabkar/HDD/HDD_ICs.txt http://www.users.on.net/~fzabkar/HDD/TVS_diodes.txt If you upload a detailed photo of the component side of the drive's PCB, maybe I could help you locate the faulty component. That said, if the drive spins up, then the PCB is probably OK. The fault will instead be inside the HDA. If you wish to replace the TVS diode, then you can use an SMBJ12A in place of the 12V diode, and an SMAJ5.0A in place of the 5V diode. Both parts are available from Farnell, Mouser, Digikey. Be aware that early model drives are not protected by TVS diodes. Also, when such a diode is present, there will sometimes be a fuse (Samsung), or zero-ohm resistor (WD), or inductor (Seagate), or polyswitch (Hitachi) in series with the supply. These often go open-circuit and will need to be bridged with a short piece of wire. Alternatively, you could use a 2A smt fuse: Littelfuse Surface Mount Fuses, N = 2A, S = 4A: http://www.farnell.com/datasheets/48294.pdf Reasonable instructions. I have seen transils (TVS diodes) on quite a few HDDs. They are pretty cheap and pretty effective. However, as the PSU and mainboard of the OP still works, I doubt overvoltage was the problem. Arno -- Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email: GnuPG: ID: 1E25338F FP: 0C30 5782 9D93 F785 E79C 0296 797F 6B50 1E25 338F ---- Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans |
#25
|
|||
|
|||
Can high voltage from power supply damage harddrive?
On Sun, 29 Aug 2010 16:57:02 +1000, Franc Zabkar
wrote: On Sat, 28 Aug 2010 22:40:18 -0400, mm put finger to keyboard and composed: So, if I could get an identical drive, I could replace the circuit board myself??? I have 40 years part-time experience in electronic repairs including soldering. In modern drives, you will need to transplant the 8-pin serial EEPROM This drive was sold January of 2004. Is that modern enough that I would have to transplant the EEPROM? (of course that also makes it harder to get a copy of the drive, even without the same software that Devils mentioned. I don't know the drive model number yet. Yousuf, if I had two dead drives, maybe I could set up a dead drive museum for the neighborhood children. I probably have other drives I could include. Maybe for Halloween. chip, or its contents, from patient to donor. This chip stores unique, drive specific calibration data. Identical drives manufactured in the same factory on the same day will have different ROM contents. In particular, there are "adaptive" data for each head. OTOH, this could account for why the first guy didn't try to fix the drive, and didn't charge either, or didn't charge much. Thanks all. The following article explains why drives have adaptive data. HDD from inside: Tracks and Zones. How hard it can be? http://hddscan.com/doc/HDD_Tracks_and_Zones.html Essentially the reason is that no two heads are physically identical. HD manufacturers try to fit as much data as possible onto each platter. To do this, they take advantage of any head that performs better than the average. For example, some heads will have a better frequency response than others, which means that you can cram more bits on each track. This technique is called Variable Bits Per Inch (VBPI). Giant magnetorestive (GMR) heads use a separate element for writing and another for reading. The separation between these two components varies from head to head. Once again manufacturers optimise data density by implementing Variable Tracks Per Inch (VTPI). Each HD therefore needs to be calibrated to account for VBPI and VTPI, otherwise the drive doesn't know where to find the tracks, or the data within the track. When a drive powers up, it needs to retrieve the bulk of its firmware from a reserved area (System Area) on the platters. If it can't read these data, then it clicks. This is what usually happens after you swap a board without transferring the calibration information. That said, you may be lucky, and the tolerances between patient and donor may be close enough to allow you to access your data without a ROM transfer. - Franc Zabkar |
#26
|
|||
|
|||
Can high voltage from power supply damage harddrive?
On Aug 29, 1:03 am, Yousuf Khan wrote:
I'm pretty certain a lack of power was what killed one of my old 500GB drives a few years back. Up until that time, it was working perfectly, there were no SMART errors, etc. Then one day, I added another hard drive into the system, and this one just stopped functioning simultaneously. The only plausible answer is that the PS wasn't putting enough power out to run all of the drives at the same time. A more plausible answer is static electric discharge from your hand. You would not even know you generated that discharge. Many other reasons also exist. All disk drives see 'lack of power'. That is the message that tells every drive (even long before the PC existed) that power has been turned off. Disk drives work normally. Or if power (voltage) is too low, the disk drive says, "Oh, this is a power off", and then does the normal shutdown procedure. Accurately noted by others. A power supply (with standard and required functions) will not destroy a disk drive. Many computer techs without electrical knowledge will simply blame mythical surges – because that is what most people are told to blame. mm - it is possible to obtain an identical drive from a used component house. As others noted, your firmware revision on that new drive must be identical. Since it costs tens of dollars to buy one, well, I have had good experiences recovering data this way. But again, be careful that firmware revisions are identical for drives with same model number. If you don't already know it, torx drives are often necessary to swap the boards. |
#27
|
|||
|
|||
Can high voltage from power supply damage harddrive?
mm wrote:
I just talked to my friend who gave me the Dell computer, and he said that his repair guy told him the reason his harddrive failed may (likely?) have been a surge or something coming from the power supply. I haven't fixed a computer power supply in a while, so I haven't seen this. But a common problem on monitor switching supplies is bad caps. As the caps go bad, the ripple on the output goes up. The average value is still regulated and would read ok on your multimeter. Problem is that the peak voltage can go way up. I had one monitor with a completely open cap. The peak voltage was 20V while the average voltage was still 5V. That 20 V took out every chip on the board. Is this a cause of harddrive failure? A common cause? A conceivable cause but really a guess by the repairman. FWIW, the repairman sent the HD somewhere to get the data off, but it was too dead or something to do that, and now they want 1500 to 3500 dollars to do it the hard way. FWIW, the mobo still seems good, although w/o the harddrive, it just displays a few lines and displays a one-line message about no SATA drive, press f2 to do this, f4 to do that. Could I turn on the computer and connect a voltmeter to the hardrive power connector** and watch the needle for a few hours (while I do other things), or do I have to watch for weeks to get a good idea? **Or do another connector on the same power supply, since the SATA power connector looks very small? Thanks. |
#28
|
|||
|
|||
Can high voltage from power supply damage harddrive?
On 29 Aug 2010 18:07:25 GMT, Arno put finger to
keyboard and composed: In comp.sys.ibm.pc.hardware.storage Franc Zabkar wrote: On Sat, 28 Aug 2010 20:49:19 -0400, mm put finger to keyboard and composed: In most cases there is an easy no-cost DIY fix. It involves using a pair of flush cutters to remove a shorted TVS (transient voltage suppression) diode. That is stupid. It is there for a reason. You always need to repair protection circuitry, not just remove it. Otherwise you end up like the Deepwhater Horizon. Replace the diode if you want to keep using your drive. Otherwise, use a good PSU, recover your data, and replace the drive. I have seen transils (TVS diodes) on quite a few HDDs. They are pretty cheap and pretty effective. However, as the PSU and mainboard of the OP still works, I doubt overvoltage was the problem. Arno All modern drives appear to have them. They don't always manage to contain the damage. I answer questions about TVS diodes almost every day, in various forums. - Franc Zabkar -- Please remove one 'i' from my address when replying by email. |
#29
|
|||
|
|||
Can high voltage from power supply damage harddrive?
On Sun, 29 Aug 2010 14:38:19 -0400, mm put
finger to keyboard and composed: On Sun, 29 Aug 2010 16:57:02 +1000, Franc Zabkar wrote: In modern drives, you will need to transplant the 8-pin serial EEPROM This drive was sold January of 2004. Is that modern enough that I would have to transplant the EEPROM? I don't know. That would best be answered by a data recovery specialist. - Franc Zabkar -- Please remove one 'i' from my address when replying by email. |
#30
|
|||
|
|||
Can high voltage from power supply damage harddrive?
On Sun, 29 Aug 2010 13:26:50 -0400, Arno wrote:
in modern installations. With below ground mains, the surge risk is very, very small. Common misconception. From ... http://tdworld.com/mag/power_underground_cable_program/ "A review of the test results and general lightning attraction theory shows that the incidence of damaging strikes to cables could be greater than expected and, in some cases, may rival overhead line direct strokes." Regards, Dave Hodgins -- Change nomail.afraid.org to ody.ca to reply by email. (nomail.afraid.org has been set up specifically for use in usenet. Feel free to use it yourself.) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Power supply supplies voltage when off | Lee M. | Homebuilt PC's | 7 | April 12th 08 06:24 AM |
Archos MiniCDRW2 power supply voltage? | mike | Cdr | 0 | May 30th 05 11:22 AM |
Power Supply Voltage problem!?!? | Sean | Homebuilt PC's | 8 | February 28th 04 10:04 PM |
wrong AT power supply connecting damage the MB ? | Dimitar Pavlov | General Hardware | 2 | January 8th 04 05:24 PM |