If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
WWNs of HBAs
Hi all,
I'm trying to look for ways to find out the WWNs of the HBAs from different types of hosts. Solaris: For 5.10 there's the command "fcinfo hba-port". For 5.8/5.9 and on certain 5.10 boxes without binary, I have difficulty getting the info - /var/adm/messages doesn't seem to contain the info. "cfgadm -al" shows the target but not the HBA... AIX: lscfg -vl fcs0 -- the above works but info from log is more desirable. IRIX: scsiha -w 2 - the above works but info from log is more desirable. HPUX: fcmsutil /dev/td0 - the above works but info from log is more desirable. Windows: Mystery??? Thanks for any input. Ernest |
#2
|
|||
|
|||
WWNs of HBAs
ernest wrote:
Hi all, I'm trying to look for ways to find out the WWNs of the HBAs from different types of hosts. Solaris: For 5.10 there's the command "fcinfo hba-port". For 5.8/5.9 and on certain 5.10 boxes without binary, I have difficulty getting the info - /var/adm/messages doesn't seem to contain the info. "cfgadm -al" shows the target but not the HBA... For Solaris 5.8 and 5.9, have a look at the "luxadm" command ...... |
#3
|
|||
|
|||
WWNs of HBAs
for windows, Qlogic and Emulex provide host applications that will display
this info. SCSI Utility For Windows will display this information for both vendors w/out the need for separate applications. Another method would be to log into your fibre channel switches and have a look here. They will display the WWPN and WWNN of all nodes logged in with the fabric. This method will be o/s agnostic. The Moojit "ernest" wrote in message oups.com... Hi all, I'm trying to look for ways to find out the WWNs of the HBAs from different types of hosts. Solaris: For 5.10 there's the command "fcinfo hba-port". For 5.8/5.9 and on certain 5.10 boxes without binary, I have difficulty getting the info - /var/adm/messages doesn't seem to contain the info. "cfgadm -al" shows the target but not the HBA... AIX: lscfg -vl fcs0 -- the above works but info from log is more desirable. IRIX: scsiha -w 2 - the above works but info from log is more desirable. HPUX: fcmsutil /dev/td0 - the above works but info from log is more desirable. Windows: Mystery??? Thanks for any input. Ernest |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
failover cluster using 64 bit windows 2k3 on single HBAs and DS400 with dual controller | [email protected] | Storage & Hardrives | 5 | April 18th 06 04:58 PM |
Help in troubleshooting connection of Emulex HBAs to an SGI TP9500 | Michael E. Thomadakis | Storage & Hardrives | 0 | February 10th 06 07:01 AM |
HBAs | Robert Wessel | Storage & Hardrives | 1 | April 3rd 04 09:04 PM |
sharing HBAs between disk and tape | Keith Michaels | Storage & Hardrives | 4 | September 10th 03 11:42 AM |