If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
OC a 2600 barton, factory unlocked
Hi all, need your help. I want to know what might be stopping me from
overclocking any higher. I have a 2600 factory unlocked barton with SLK-900U HS 2x512 Corsair XMS3200C2PT set at timings of 2.5-3-3-6;(2.5-3-3-11 does nothing more in stability or speed for me) Abit AN7 board; 400W PSU At factory 11.5 muliplier, I'm maxed out at 195fsb. At 11X, I can push it to 200fsb. And if I set multiplier at 10.5X, i can go up to 210fsb. I've used vcore of 1.8V(that high enough?) and my Vdim is at 2.8V. Any suggestions on why I can't go higher? what's stopping me? Temps never go above 45 under load in any setup. Seems my cpu can't cross the 2.3ghz limit Thanks all |
#2
|
|||
|
|||
On Sat, 06 Nov 2004 19:35:23 -0500, frank wrote:
Hi all, need your help. I want to know what might be stopping me from overclocking any higher. I have a 2600 factory unlocked barton with SLK-900U HS 2x512 Corsair XMS3200C2PT set at timings of 2.5-3-3-6;(2.5-3-3-11 does nothing more in stability or speed for me) Abit AN7 board; 400W PSU At factory 11.5 muliplier, I'm maxed out at 195fsb. At 11X, I can push it to 200fsb. And if I set multiplier at 10.5X, i can go up to 210fsb. I've used vcore of 1.8V(that high enough?) and my Vdim is at 2.8V. Any suggestions on why I can't go higher? what's stopping me? Temps never go above 45 under load in any setup. Seems my cpu can't cross the 2.3ghz limit With all the FSB variations, I'd say the cpu is at or very close to it's limits. That's a little on the low side, but 11x200 is still a 3200+, so not real bad. -- Abit KT7-Raid (KT133) Tbred B core CPU @2400MHz (24x100FSB) http://mysite.verizon.net/res0exft/cpu.htm |
#3
|
|||
|
|||
You might try increasing the vcore to 1.825 or 1.85. I wouldn't go any
higher than 1.9 on the vcore with air cooling. You also might try 3 3 3 8 on the ram. Some of the abit nf2 motherboards undervolt the vcore by about 0.02v, might want to check this one. I have a NF7-S 1700+ (680 A core) at 11.0 x 173fsb on 1.875v with DDR2100 @ 2.8v 173fsb (3 3 3 11) using a thermaltake silent boost with a vantec tornado reo/controlled. Max temp load at 80W is 46°C and the best I can figure I get a 0.25 C/W from the heat sink / fan combo with a fan speed of 4400rpm. The SLK-900U is a better heat sink and therefore you shouldn't have to worry to much about temps. good luck and i hope this helps "frank" wrote in message ... Hi all, need your help. I want to know what might be stopping me from overclocking any higher. I have a 2600 factory unlocked barton with SLK-900U HS 2x512 Corsair XMS3200C2PT set at timings of 2.5-3-3-6;(2.5-3-3-11 does nothing more in stability or speed for me) Abit AN7 board; 400W PSU At factory 11.5 muliplier, I'm maxed out at 195fsb. At 11X, I can push it to 200fsb. And if I set multiplier at 10.5X, i can go up to 210fsb. I've used vcore of 1.8V(that high enough?) and my Vdim is at 2.8V. Any suggestions on why I can't go higher? what's stopping me? Temps never go above 45 under load in any setup. Seems my cpu can't cross the 2.3ghz limit Thanks all |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Passing 2.28 GHz on a 2600 Barton? | OD2rileec | Overclocking | 10 | May 6th 04 02:10 PM |
2800 Barton unlocked or not ... | Toby Edwards | Overclocking AMD Processors | 2 | April 23rd 04 12:40 PM |
Mobile Barton 2500 Unlocked ? | Jim Reynolds | Overclocking AMD Processors | 2 | March 31st 04 07:06 AM |
Is (locked) Barton 2600 XP a bad overclocker? | Richard | Overclocking AMD Processors | 7 | December 27th 03 04:26 PM |
A7V600 + unlocked Barton 2500+ and 133MHz RAM | DavidS | Overclocking AMD Processors | 4 | November 13th 03 07:31 AM |