If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
change hard drive to IDE 3 using Promise 20276 controller
I would like to change my hard drive connection from IDE 1 to IDE 3 on
my gigabyte GA-8IEXP motherboard. I would also like to utilize the ATA133 feature of IDE 3 which uses the Promise 20276 chip. My OS is Mandrake 10.0 , (2.6.3.7 kernel). I only have the one hard drive and it is hda on IDE 1. I believe IDE 3 equates to hde. Can I just edit the etc/lilo.conf file and replace hda with hde, then plug in my hard drive to IDE 3? Do I need to modify the etc/fstab file or any other files? As for the ATA 133 feature, my manual says I need to load the Promise driver for my OS. However, tech support told me I don't need the promise driver, I could just follow the procedure here, http://www.geocities.com/ender7007/. That procedure is for a new install and I don't want to wipe my hard drive. Is there another way to boot from hde? Do I need the driver? Can I use the one for RedHat? I looked at the proc/pci file, it's empty. My goal it to get my hard drive on IDE 3, and eventually put a second hard drive on IDE 4. Then I can put my DVD drive on IDE 1 and CD drive on IDE 2. I tried my DVD drive on IDE 3, it runs painfully slow. Promise tech support told me the 20276 chip works better with hard drives as compared to DVD or CD drives so that's why I'm trying to get my hard drive on IDE 3. I'm new to Linux, a few months now and could really use some help. Thanks, Kooner. |
#2
|
|||
|
|||
change hard drive to IDE 3 using Promise 20276 controller
On Thursday 27 April 2006 23:24, Kooner stood up and spoke the following
words to the masses in /alt.os.linux.mandrake...:/ I would like to change my hard drive connection from IDE 1 to IDE 3 on my gigabyte GA-8IEXP motherboard. I would also like to utilize the ATA133 feature of IDE 3 which uses the Promise 20276 chip. My OS is Mandrake 10.0 , (2.6.3.7 kernel). I only have the one hard drive and it is hda on IDE 1. I believe IDE 3 equates to hde. More precisely, if every IDE channel has a master and a slave, and if you plan on attaching the hard disk to the master of the third IDE channel, then it would be */dev/hde,* yes. The slave of that channel would be */dev/hdf.* Can I just edit the etc/lilo.conf file and replace hda with hde, then plug in my hard drive to IDE 3? Do I need to modify the etc/fstab file or any other files? Yes, */etc/fstab* will need to be modified as well. However, I recommend doing the modifications while booted up from a Live or Rescue CD, mounting your hard disk's root partition on */mnt* and thus changing */mnt/etc/fstab* and */mnt/etc/lilo.conf.* In order to save the LILO changes to the master boot record of the hard disk, you will then have to issue... lilo -C /mnt/etc/lilo.conf -b /dev/hde See... man lilo .... for details. As for the ATA 133 feature, my manual says I need to load the Promise driver for my OS. Every piece of hardware requires a driver. However, chances are that the kernel will autodetect your controller and load the driver module for it. However, tech support told me I don't need the promise driver, I could just follow the procedure here, http://www.geocities.com/ender7007/. That procedure is for a new install and I don't want to wipe my hard drive. That procedure is also for RedHat Linux 6.2, which uses a 2.2 kernel. A lot has changed in the meantime... ;-) Is there another way to boot from hde? Modify the files you need to modify - see my explanation above - and all should go well... ;-) Do I need the driver? I get the feeling that you are talking about "the driver" as being some separately supplied software module, or worse: a Windows-specific driver - most helpdesks are unaware of the fact that there are still other operating systems out there than Microsoft Windows... grin Can I use the one for RedHat? A driver is a driver, and it is or should be part of the kernel tree. Drivers should also match the kernel version. I'm not an expert on IDE drivers, but I do believe that the driver module for the adapter you are referring to already is part of the /vanilla/ Linux kernel tree. And just once again...: the procedure you are referring to in that hyperlink you pasted is for RedHat 6.2, which is seriously outdated. I looked at the proc/pci file, it's empty. Does the output of... dmesg .... reveal anything about the controller? My goal it to get my hard drive on IDE 3, and eventually put a second hard drive on IDE 4. Then I can put my DVD drive on IDE 1 and CD drive on IDE 2. I tried my DVD drive on IDE 3, it runs painfully slow. Probably because you haven't enabled DMA for that adapter. Check out... man hdparm Promise tech support told me the 20276 chip works better with hard drives as compared to DVD or CD drives so that's why I'm trying to get my hard drive on IDE 3. I'm new to Linux, a few months now and could really use some help. Thanks, If you're new to GNU/Linux, then perhaps I should mention that all commands I have mentioned in my reply - except for the commands that show you a /man/ page - require root access. Good luck! ;-) -- With kind regards, *Aragorn* (Registered GNU/Linux user #223157) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hard Drive Temperature | Nehmo | Storage (alternative) | 37 | October 27th 05 12:35 AM |
How to install 2nd HDD with Partition Magic 6.0 partitions under Windows ME? | Phred | Dell Computers | 13 | February 18th 04 08:45 AM |
Removable Drive Bays | Rod Speed | Storage (alternative) | 35 | January 3rd 04 08:31 PM |
Multi-boot Windows XP without special software | Timothy Daniels | General | 11 | December 12th 03 05:38 AM |
Asus A7N8X, WD 120GB hard drive and Promise ATA133 Controller | [email protected] | Storage (alternative) | 0 | October 28th 03 07:15 AM |