If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Trouble cloning XP with Ghost 2003
The boot disk for my XP system has been having a number of bad sector
problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? Thanks, Kevin |
#2
|
|||
|
|||
Did you boot XP after you have installed a 2nd drive, before using Ghost
2003 (booted from DOS/floppy)? "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? Thanks, Kevin |
#3
|
|||
|
|||
Yes, I drive was installed prior to installing ghost.
I followed the directions in Ghost's readme, and have tried using both -FDSZ and -FDSP. - Kevin "Peter" wrote in message ... Did you boot XP after you have installed a 2nd drive, before using Ghost 2003 (booted from DOS/floppy)? "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? Thanks, Kevin |
#4
|
|||
|
|||
"Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? You basically have to unplug the original drive for the first boot after the drive has been cloned and boot off the copy. XP will claim to have detected new hardware and ask to be allowed to reboot. Once you have allowed that, you can put the original drive back in the system if you want, if you say want to use it for video capture etc. If XP can see both the original and the copy during the first boot after the original has been cloned, it gets seriously confused, even if you boot off the copy and it uses files off the original for the boot. |
#5
|
|||
|
|||
I don't give XP a chance to see the clone-- I've been powering off and
removing the original drive as soon as Ghost completes. "Rod Speed" wrote in message ... "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? You basically have to unplug the original drive for the first boot after the drive has been cloned and boot off the copy. XP will claim to have detected new hardware and ask to be allowed to reboot. Once you have allowed that, you can put the original drive back in the system if you want, if you say want to use it for video capture etc. If XP can see both the original and the copy during the first boot after the original has been cloned, it gets seriously confused, even if you boot off the copy and it uses files off the original for the boot. |
#6
|
|||
|
|||
Really? I've read messages about people using Ghost to successfully clone
their aging XP drive. How do I copy the boot sectors? - Kevin wrote in message ... On Sun, 16 Jan 2005 22:47:39 -0500, "Kevin" wrote: Yes, I drive was installed prior to installing ghost. I followed the directions in Ghost's readme, and have tried using both -FDSZ and -FDSP. - Kevin The Boot Sectors are not copied with Ghost.. "Peter" wrote in message ... Did you boot XP after you have installed a 2nd drive, before using Ghost 2003 (booted from DOS/floppy)? "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? Thanks, Kevin |
#7
|
|||
|
|||
Kevin wrote in message ... I don't give XP a chance to see the clone-- I've been powering off and removing the original drive as soon as Ghost completes. Then presumably the clone isnt successful because of the state of the original drive, partially failed. "Rod Speed" wrote in message ... "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? You basically have to unplug the original drive for the first boot after the drive has been cloned and boot off the copy. XP will claim to have detected new hardware and ask to be allowed to reboot. Once you have allowed that, you can put the original drive back in the system if you want, if you say want to use it for video capture etc. If XP can see both the original and the copy during the first boot after the original has been cloned, it gets seriously confused, even if you boot off the copy and it uses files off the original for the boot. |
#8
|
|||
|
|||
But the original drive can boot. If the clone is a bitwise copy of the
original, shouldn't it be able to boot? "Rod Speed" wrote in message ... Kevin wrote in message ... I don't give XP a chance to see the clone-- I've been powering off and removing the original drive as soon as Ghost completes. Then presumably the clone isnt successful because of the state of the original drive, partially failed. "Rod Speed" wrote in message ... "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? You basically have to unplug the original drive for the first boot after the drive has been cloned and boot off the copy. XP will claim to have detected new hardware and ask to be allowed to reboot. Once you have allowed that, you can put the original drive back in the system if you want, if you say want to use it for video capture etc. If XP can see both the original and the copy during the first boot after the original has been cloned, it gets seriously confused, even if you boot off the copy and it uses files off the original for the boot. |
#9
|
|||
|
|||
Got it working-- not exactly sure what the problem was. It was either a) I
needed to run Ghost from floppy, or b) I needed to bring up the boot menu in BIOS and explicitly tell it to boot from the IDE drive (even though that was the only option). Anyway, thanks for the suggestions & ideas. - Kevin "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? Thanks, Kevin |
#10
|
|||
|
|||
Kevin wrote in message ... But the original drive can boot. If the clone is a bitwise copy of the original, shouldn't it be able to boot? In theory, yes. In practice the different detail on sector access may see the sector contents not copied properly when the clone is made, but be good enough on retrys to allow it to boot in the original. You did say you got an error message that complained about a boot failure before the win screens show up. You could also try repairing the bad clone. I wouldnt personally because you dont know what else didnt clone properly apart from the boot stuff, and that can bit late, but its less work that a completely clean reinstall. "Rod Speed" wrote in message ... Kevin wrote in message ... I don't give XP a chance to see the clone-- I've been powering off and removing the original drive as soon as Ghost completes. Then presumably the clone isnt successful because of the state of the original drive, partially failed. "Rod Speed" wrote in message ... "Kevin" wrote in message ... The boot disk for my XP system has been having a number of bad sector problems lately, so I decided to try to clone it to a new drive. I installed a 2nd drive, formatted it, and used Norton Ghost 2003 to do a clone of the boot (C drive to it. When the clone is complete, I power off, swap the cable and set the jumpers, but get a "boot failure from previous device" error on startup (after BIOS screen but before Windows). I can verify that the clone worked by booting off the original drive with the clone as a slave-- all the files seem to be there. What might I be doing wrong? You basically have to unplug the original drive for the first boot after the drive has been cloned and boot off the copy. XP will claim to have detected new hardware and ask to be allowed to reboot. Once you have allowed that, you can put the original drive back in the system if you want, if you say want to use it for video capture etc. If XP can see both the original and the copy during the first boot after the original has been cloned, it gets seriously confused, even if you boot off the copy and it uses files off the original for the boot. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Another Ghost 2003 question - Simple | Tom Jackson | Storage (alternative) | 4 | July 30th 04 04:30 PM |
Can't See New HD After Cloning with Ghost 2003 | Nehmo Sergheyev | General | 15 | March 27th 04 09:15 PM |
Norton Ghost 2003 restores entire *drive*, not just partition? | Matt | Storage & Hardrives | 5 | January 17th 04 12:20 AM |
Ghost 2003 at USB 2.0 speed | Sean | Storage (alternative) | 13 | January 5th 04 01:58 PM |
What DVD format works with Norton Ghost 2003? | van | General | 1 | October 12th 03 07:40 PM |