|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
November 21st 03, 04:08 PM
|
|||
|
|||
HSG80 Firmware / Drive capacity question
Hello,
I was wondering if my HSG80 at firmware 8.6F supports 146GB drives, or do I need to upgrade my firmware to 8.7? TIA 
|
|
#2
November 22nd 03, 11:27 PM
|
|||
|
|||
|
From memory you should be OK with 8.6. I don't remember there ever being
anything in QuickSpecs that specified that they were only supported on 8.7 and later. Cheers, Mike. "Tim" ... wrote in message ... Hello, I was wondering if my HSG80 at firmware 8.6F supports 146GB drives, or do I need to upgrade my firmware to 8.7? TIA
|
|
#3
November 23rd 03, 11:53 AM
|
|||
|
|||
|
146 GB drives on an HSG80 require firmware 8.7, you should also upgrade to
SecurePath 4. "Mike Povall" wrote in message ... From memory you should be OK with 8.6. I don't remember there ever being anything in QuickSpecs that specified that they were only supported on 8.7 and later. Cheers, Mike. "Tim" ... wrote in message ... Hello, I was wondering if my HSG80 at firmware 8.6F supports 146GB drives, or do I need to upgrade my firmware to 8.7? TIA
|
|
#4
November 23rd 03, 06:03 PM
|
|||
|
|||
|
The official word when 146 GB drives was released was ACS 8.6F-10 at a
minimum to support that capacity. Of course, it's usually best to try to use the latest firmware, ACS8.7-4 as far as I know. SecurePath 4.0c is the latest, but I don't see any direct connection between 146GB drives and SecurePath 4.0c. /charles "Ramcke545" wrote in message news:ad1wb.213911$9E1.1145807@attbi_s52... 146 GB drives on an HSG80 require firmware 8.7, you should also upgrade to SecurePath 4. "Mike Povall" wrote in message ... From memory you should be OK with 8.6. I don't remember there ever being anything in QuickSpecs that specified that they were only supported on 8.7 and later. Cheers, Mike. "Tim" ... wrote in message ... Hello, I was wondering if my HSG80 at firmware 8.6F supports 146GB drives, or do I need to upgrade my firmware to 8.7? TIA
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Skybuck's adventure with the Hitachi Deskstar 7K250 123.5 GB ;) | The Other Guy. | General | 24 | November 17th 04 07:49 PM |
| Skybuck's adventure with the Hitachi Deskstar 7K250 123.5 GB ;) | Skybuck Flying | Asus Motherboards | 15 | November 17th 04 07:49 PM |
| HELP! MY Computer cannot find hard drive | Michael S. | Asus Motherboards | 8 | June 25th 04 07:13 AM |
| Partitioning | [email protected] | Dell Computers | 13 | April 18th 04 11:45 AM |
| How to install 2nd HDD with Partition Magic 6.0 partitions under Windows ME? | Phred | Dell Computers | 13 | February 18th 04 08:45 AM |
Linear Mode
