If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Overclocking hypertransport?
Quick question from someone who hasn't overclocked in years-- I just overclocked
my new AMD X2 5050e from 200x13 2.6 GHz to 220x13 2.86 GHz, getting my DDR2 800 at the proper speed of 400 (well, a bit over) instead of the 371 it was running at. But my hypertransport bus is now pushed to 1100 MHz instead of 1000 MHz. Is that okay? System seems stable so far (after an hour or two). http://webpages.charter.net/garrison6328/cpuz.htm |
#2
|
|||
|
|||
Overclocking hypertransport?
"Darren Garrison" wrote in message ... Quick question from someone who hasn't overclocked in years-- I just overclocked my new AMD X2 5050e from 200x13 2.6 GHz to 220x13 2.86 GHz, getting my DDR2 800 at the proper speed of 400 (well, a bit over) instead of the 371 it was running at. But my hypertransport bus is now pushed to 1100 MHz instead of 1000 MHz. Is that okay? System seems stable so far (after an hour or two). http://webpages.charter.net/garrison6328/cpuz.htm It should be fine as long as it is stable and you don't see any extraordinarily high temperatures. Running a couple of instances of Orthos for a few hours should give you some idea about stability. In your case, I would run it on the 'blend' setting which stresses ram and cpu equally. Ed |
#3
|
|||
|
|||
Overclocking hypertransport?
I agree with the last poster. Also to note Hyper Transport maxing out is usually determined by the motherboard, that is your manufacturer should have stated the HT capabilities like HT 1.0, HT 2.0, or HT 3.0. From this you can determine what is the max HT you can use since it technically isn't software or OS dependent. Nowadays HT go up to, or higher in some cases, 2000MHz. |
#4
|
|||
|
|||
Overclocking hypertransport?
phaedrus06 wrote:
I agree with the last poster. Also to note Hyper Transport maxing out is usually determined by the motherboard, that is your manufacturer should have stated the HT capabilities like HT 1.0, HT 2.0, or HT 3.0. From this you can determine what is the max HT you can use since it technically isn't software or OS dependent. Nowadays HT go up to, or higher in some cases, 2000MHz. Hello, again. Apparently, you are new to Usenet. It is common practice to quote the person(s) you are responding to, as you'll note Ed did when replying to Darren. This should give you a more complete explanation: http://www.netmeister.org/news/learn2quote2.html Thanks! ----------------- www.Newsgroup-Binaries.com - *Completion*Retention*Speed* Access your favorite newsgroups from home or on the road ----------------- |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Intel and Hypertransport? | [email protected] | General | 16 | November 7th 05 05:27 AM |
amd 8131 with hypertransport | Amit Tikare | AMD x86-64 Processors | 0 | July 11th 05 09:11 AM |
HyperTransport Speed | Dave | Overclocking AMD Processors | 5 | October 22nd 04 10:17 PM |
PCI Express and Hypertransport | Melkor | AMD x86-64 Processors | 5 | September 19th 04 09:25 AM |
HT = HyperTransport | Supertimer | Overclocking AMD Processors | 0 | November 11th 03 05:40 AM |