A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » General
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Rediculously Simple Question



 
 
Thread Tools Display Modes
  #1  
Old August 5th 03, 12:43 AM
Jeremy
external usenet poster
 
Posts: n/a
Default Rediculously Simple Question

I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and was
told to use the program, NOD32 for DOS, an anti-virus program that will wipe
viruses off of HDs that formatting can't reach. What I had to do was simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from that
disk and run the program. Simple, right? It should be. So I grab a disk, pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable) and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load that
file.

So what is happening? Should I go out and buy a new pack of diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy



  #2  
Old August 5th 03, 01:39 AM
Some One
external usenet poster
 
Posts: n/a
Default

Just download the disk utility from the manufacturer of the drive. It
should be able to fit on a floppy and zero out ALL sectors on the
disk.

"Jeremy" wrote in message
...
I am really ashamed of myself for having to ask this question. I'm

no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum

and was
told to use the program, NOD32 for DOS, an anti-virus program that

will wipe
viruses off of HDs that formatting can't reach. What I had to do was

simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot

from that
disk and run the program. Simple, right? It should be. So I grab a

disk, pop
it in the A drive, tell my computer to copy over the program and a

few
seconds later I get an error message saying that there isn't enough

room on
the disk to copy the file. The file is 1.41MB and if memory serves,

the
diskette should be 1.44MB; there shouldn't be a problem. I go to the

A
drive's Properties and the disk is completely empty (not even a

lable) and
it says that the disk's free space is 1,457,664 bytes but next to

that it
says 1.38MB (File System: FAT, if that's important). What the...? I

try
formatting the disk and the capacity remains the same. I try a bunch

of my
HUNDREDS of other empty diskettes and they ALL show their capacity

at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to

load that
file.

So what is happening? Should I go out and buy a new pack of

diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank

you
very much.

Jeremy





  #3  
Old August 5th 03, 02:17 AM
Norm
external usenet poster
 
Posts: n/a
Default

Jeremy, it's the age old dilemma of millions of bytes as compared to mb. A
MB is 1024KB. If you divide 1,457,664 bytes by 1024 KB you get 1423.5KB or
1.42MB, not exactly the 1.38MB in the properties screen but pretty dam
close. So is your 1.41MB file 1,410,000 bytes or is it 1.41MB? If it's
1,410,000 bytes, then it should fit but I suspect not. There's nothing
wrong with your floppy drive or any of your floppies, that's just the way it
works. Don't know if I explained this correctly but that is my take on it.
You also mentioned having to boot from the floppy, a floppy with 1,457,664
bytes sure isn't bootable. You need a system on it, just copying a file to
it won allow it to boot. There is a program that allows you to create the
same floppy with approximately 1.6MB of space using the same floppy. I can
hunt it down for you if you want.
Have you tried running FDISK on that drive, deleting the partition and then
re-creating it?

"Jeremy" wrote in message
...
I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and

was
told to use the program, NOD32 for DOS, an anti-virus program that will

wipe
viruses off of HDs that formatting can't reach. What I had to do was

simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from that
disk and run the program. Simple, right? It should be. So I grab a disk,

pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room

on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable) and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load

that
file.

So what is happening? Should I go out and buy a new pack of diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy






  #4  
Old August 5th 03, 03:41 AM
Mickey Mouse
external usenet poster
 
Posts: n/a
Default

Normally a drive manufacturer has utilities to write zeros to the beginning
or the entire drive. At the front of the drive important information about
how the file system is set up and how the partitions are set up.

I dont know much more than this term sometimes called the MBR or master boot
record. I am not even sure if that is the front of the drive.

This is a good bit of reading on Floppy IDE and SCSI Disks at this site call
PC Lube and Tune At Yale:

http://www.yale.edu/pclt/BOOT/DISKDEV.HTM

It explains things a little more carefully.

The first 512 bytes are used by the drive initialization.
Then there is an MBR also.

After reading this information, I would say you need a floppy from another
computer containing an emergency boot disk for windows that is virus free.
What I would do is Write Protect one emergency boot disk. This makes it so
it can not be written to. Then try to use the FDISK program to completely
make new partitions. You can back up one step from here by using a utility
from the Disk Manufacturer that will write all zeros to the beginning of the
drive. That you have to get from the manufacturer usually downloadable from
their website.

FDISK makes new partitions with no file system. After than you can add the
file system by using the operating systems FORMAT command.

There are some file utilities that will force a zero to be written to each
byte so that every bit will be written to. Using these utilities from the
manufacturer the entire drive can be formatted and written to including the
first 512 bytes.


The US Government uses a utility called KillDisk that you can look for on
the Internet also. KILLDISK is a program the government uses to destroy
classified data on hard drives. It is suppose to change repeatedly every
byte of data on the drive.

"Jeremy" wrote in message
...
I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and

was
told to use the program, NOD32 for DOS, an anti-virus program that will

wipe
viruses off of HDs that formatting can't reach. What I had to do was

simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from that
disk and run the program. Simple, right? It should be. So I grab a disk,

pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room

on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable) and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load

that
file.

So what is happening? Should I go out and buy a new pack of diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy





  #5  
Old August 5th 03, 04:06 AM
kony
external usenet poster
 
Posts: n/a
Default

On Mon, 4 Aug 2003 16:43:26 -0700, "Jeremy"
wrote:

I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and was
told to use the program, NOD32 for DOS, an anti-virus program that will wipe
viruses off of HDs that formatting can't reach. What I had to do was simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from that
disk and run the program. Simple, right? It should be. So I grab a disk, pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable) and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load that
file.

So what is happening? Should I go out and buy a new pack of diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy


1.44MB is the unformatted capacity. After formatting to FAT16 it'll
be 1.38MB.

Since you've already tried formatting the hard drive, I"ll assume
you're not trying to preserve/recover any data from it?

Boot to a windows startup floppy, FDISK /MBR the hard drive at the
prompt. Then run FDISK again and see what the partitions look like,
and if all space is accounted for. Given that you just received the
drive, at this point it'd be good to run the manufacturer's
diagnostics to confirm that the drive is viable, in proper working
order. Just be sure to boot from the floppy, NOT that hard drive (I'm
suggesting that you don't need NOD32).


Dave

  #6  
Old August 5th 03, 06:24 PM
rcm
external usenet poster
 
Posts: n/a
Default

It is not unformatted capacity! 1.44 is the formatted capacity in megabytes
(where m=1,000,000).

All thes sizes are correct, it is the units definition that is used.

http://www.pcguide.com/ref/fdd/formatSummary-c.html

Unformatted Capacity ~2 MB
Formatted Capacity (binary kilobytes) 1,440
Formatted Capacity (bytes) 1,474,560
File System Overhead (bytes) 16,896
Total Usable Capacity (bytes) 1,457,664
Total Usable Capacity (binary KB) 1,423.5
Total Usable Capacity (binary MB) 1.390






"kony" wrote in message
...
On Mon, 4 Aug 2003 16:43:26 -0700, "Jeremy"
wrote:

I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and

was
told to use the program, NOD32 for DOS, an anti-virus program that will

wipe
viruses off of HDs that formatting can't reach. What I had to do was

simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from

that
disk and run the program. Simple, right? It should be. So I grab a disk,

pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room

on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable)

and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of

my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load

that
file.

So what is happening? Should I go out and buy a new pack of diskettes

that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy


1.44MB is the unformatted capacity. After formatting to FAT16 it'll
be 1.38MB.

Since you've already tried formatting the hard drive, I"ll assume
you're not trying to preserve/recover any data from it?

Boot to a windows startup floppy, FDISK /MBR the hard drive at the
prompt. Then run FDISK again and see what the partitions look like,
and if all space is accounted for. Given that you just received the
drive, at this point it'd be good to run the manufacturer's
diagnostics to confirm that the drive is viable, in proper working
order. Just be sure to boot from the floppy, NOT that hard drive (I'm
suggesting that you don't need NOD32).


Dave



  #7  
Old August 5th 03, 06:42 PM
Tom @ HollyLodge
external usenet poster
 
Posts: n/a
Default

use a CD and get bootmanager from http://btmgr.sourceforge.net/, to load
from the CD


"rcm" wrote in message
. ca...
It is not unformatted capacity! 1.44 is the formatted capacity in

megabytes
(where m=1,000,000).

All thes sizes are correct, it is the units definition that is used.

http://www.pcguide.com/ref/fdd/formatSummary-c.html

Unformatted Capacity ~2 MB
Formatted Capacity (binary kilobytes) 1,440
Formatted Capacity (bytes) 1,474,560
File System Overhead (bytes) 16,896
Total Usable Capacity (bytes) 1,457,664
Total Usable Capacity (binary KB) 1,423.5
Total Usable Capacity (binary MB) 1.390






"kony" wrote in message
...
On Mon, 4 Aug 2003 16:43:26 -0700, "Jeremy"
wrote:

I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum

and
was
told to use the program, NOD32 for DOS, an anti-virus program that will

wipe
viruses off of HDs that formatting can't reach. What I had to do was

simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from

that
disk and run the program. Simple, right? It should be. So I grab a

disk,
pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough

room
on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable)

and
it says that the disk's free space is 1,457,664 bytes but next to that

it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of

my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load

that
file.

So what is happening? Should I go out and buy a new pack of diskettes

that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank

you
very much.

Jeremy


1.44MB is the unformatted capacity. After formatting to FAT16 it'll
be 1.38MB.

Since you've already tried formatting the hard drive, I"ll assume
you're not trying to preserve/recover any data from it?

Boot to a windows startup floppy, FDISK /MBR the hard drive at the
prompt. Then run FDISK again and see what the partitions look like,
and if all space is accounted for. Given that you just received the
drive, at this point it'd be good to run the manufacturer's
diagnostics to confirm that the drive is viable, in proper working
order. Just be sure to boot from the floppy, NOT that hard drive (I'm
suggesting that you don't need NOD32).


Dave





  #8  
Old August 5th 03, 10:19 PM
ljg
external usenet poster
 
Posts: n/a
Default

Can't you just compress the floppy when you format it?

On Mon, 4 Aug 2003 16:43:26 -0700, "Jeremy"
wrote:

I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and was
told to use the program, NOD32 for DOS, an anti-virus program that will wipe
viruses off of HDs that formatting can't reach. What I had to do was simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from that
disk and run the program. Simple, right? It should be. So I grab a disk, pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable) and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load that
file.

So what is happening? Should I go out and buy a new pack of diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy



  #9  
Old August 5th 03, 11:55 PM
DaveW
external usenet poster
 
Posts: n/a
Default

Sorry, but the floppies are 1.44MB in capacity BEFORE mandatory Formatting.
After Formatting they have 1.38 MB of capacity. This is true of all
standard IBM high density floppies. No way around it.

--
DaveW



"Jeremy" wrote in message
...
I am really ashamed of myself for having to ask this question. I'm no
computer expert but I should know better:

A friend game me a 40GB hard drive that has a virus on it. I tried
formatting it but the virus remained. I posted my problem in a forum and

was
told to use the program, NOD32 for DOS, an anti-virus program that will

wipe
viruses off of HDs that formatting can't reach. What I had to do was

simple:
Move the program (which is 1.41MB) onto a 3x3.5" disk, then boot from that
disk and run the program. Simple, right? It should be. So I grab a disk,

pop
it in the A drive, tell my computer to copy over the program and a few
seconds later I get an error message saying that there isn't enough room

on
the disk to copy the file. The file is 1.41MB and if memory serves, the
diskette should be 1.44MB; there shouldn't be a problem. I go to the A
drive's Properties and the disk is completely empty (not even a lable) and
it says that the disk's free space is 1,457,664 bytes but next to that it
says 1.38MB (File System: FAT, if that's important). What the...? I try
formatting the disk and the capacity remains the same. I try a bunch of my
HUNDREDS of other empty diskettes and they ALL show their capacity at
1.38MB. Aren't these disks supposed to be 1.44MB? I need 1.41MB to load

that
file.

So what is happening? Should I go out and buy a new pack of diskettes that
reads "1.44MB" on the side? I hope not. I already have TONS of empty
diskettes already that I'm not even using. Can anyone help me? Thank you
very much.

Jeremy





  #10  
Old August 10th 03, 03:19 AM
Me
external usenet poster
 
Posts: n/a
Default

Low-Level-Format it.

--
I believe in having an open mind,
but not so open that my brains fall out.



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Simple Question? Sean General 5 August 5th 03 04:09 AM
Motherboard FSB - Newbie Question mac General 1 August 2nd 03 03:16 AM
HDD Boot-sector virus question -ha- General 2 July 19th 03 07:56 AM
PSU Question xonics General 1 July 18th 03 04:31 PM
Memory question for Intel 865PERL grendel General 1 July 7th 03 04:56 AM


All times are GMT +1. The time now is 12:04 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.