If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
On Thu, 06 Jan 2005 14:00:41 GMT, Ken wrote:
Raymond A. Chamberlin wrote: On Wed, 05 Jan 2005 13:53:26 GMT, Ken wrote: I did a lot of clipping of old text. What I mean is even if NO software was loaded the lamp would come on. Once the software is loaded for the control of the lamp, it should turn off and on the lamp if you follow the procedure I described using WATCH.EXE. Well, in its present condition, the lamp stays on no matter what. When the scanner was working right, the light was always ON as long as power was applied to the scanner. However, I never tried, at that time, to see what would happen if I double-clicked Watch.exe. The reason it stays on presently, is the scanner is not recognized and therefore the software (watch.exe) is unable to control the lamp. Since the lamp will come one even if the scanner is not connected to the computer, it will always be on. Remember, to make the lamp go OFF once the icon exists in the lower right corner of your screen, you must do the "Right click on it and choose EXIT, YES" routine. It is NOT working that way now because the software is unable to see the scanner. The software is loaded by virtue of the icon being present, and there not having been an error message saying that a file could not be found during the loading of that program. Well, an email request to Mostek USA (automatically, I guess) got me instructions on exactly how to pull all the twains and twunks and reinstall new ones. Apparently I didn't have to uninstall the image program bundled with the scanner, as I did before. The only significant difference I could see between what these instructions said and what I did before to remove this stuff (I still don't understand whether their term 'scanner driver' refers to all these twains and twunks or something else.) was that I didn't disable my virus auto-protect program. Their instructions included getting a different "driver" from their Website, which I did -- '123ep22.exe', which came out in 1999. The one on my CD, that I used before, is 'd12epe22.exe'. Which one do you use? So I installed this newer "driver". I note that it leaves out the 'Twain' folder, only installing the 'Twain32' folder into the Windows folder. Isn't the 'Twain' folder just for 16=bit-word machines anyhow? So, OK, now I don't get a flag saying it can't detect the scanner, but I still get one that says it can't find 'twain.dll' in the Windows folder, although this file IS in the Windows folder. So I guess I'll uninstall that driver collection and reinstall the d12epe22 one per their instructions and see if that works. We can certainly forget all this discussion about when the scanner lamp should be ON though. At present, when it DOESN'T say it can't find the scanner, that light still does NOT go on and off with the tray icon; it's ALWAYS ON. If it does in your case, it must be that units having some ranges of serial do that, while others don't. The power input at the scanner's main board measures 15 v. That is correct for the wall wart. Other reasons could be corrupted software, bad parallel port or cable from the port, or defective logic in the scanner. I located two components on the main board that appeared to be power regulators. I don't know their pinouts, but the only pins that measured significant voltages other than 15 v showed 3 and 12 v, respectively. One of the outside pins (the left one if I recall correctly, but don't hold me to this) should be the input voltage. In this case, 15v. The center pin is Ground. The right terminal is the output voltage, 12v. You might not be placing your common lead of your DVM to true ground when you measured the center terminal. Sometimes these circuits do not use the same ground as your computer uses. The other regulator should work the same way, but the output should be +5v. (I think) The marking on the regulators should read something like 9805 and 9812 indicating the +5 and +12 volt output. I don't think there's any problem there. I measured with respect to the INPUT power-cable ground. I measured the +12 and +3 on different pins relative to the same physical start of pin count. The other non-15-v pins on the two regulators had very low voltages. There are no markings on the regulators. See above. If I were to guess, (and I don't care much for guessing) that is what I would guess. For what it is worth, you could open up the scanner and see if you can reach the two regulators. A simple DVM should allow you to measure their output as they are both three terminal through-hole components if my memory serves me. See above. I agree however, that you are more likely to find software or the port to be the problem. Now this would seem to indicate that the software loaded properly and that all the files necessary were OK. How would that assure that ALL the files were loaded properly? If the software were NOT loaded properly, there should have been an error message saying that a file was not found or could not load. Nothing is 100%, but that would be the case most of the time. Whatever. Software types have no constraints. It's all seat-of-the-pants. It's all chaos to me. This is probably due to the fact it cannot see the scanner. It should have gone out if everything was working. It stayed on. Since you do not want to test the parallel port (and I understand why), removing ALL the software and reloading it is about all you can do. Remember to delete the directories created by the current installation so that no file such as the initialization files remain. This is a little surprising in that I would have thought there would have been no scanner listed there. Who knows, it might be placed there even if it was not detected? That portion of my file reads: [Watch] Model=A4S2600_Watch LampStatus=0 ActiveTime=4923599 GreenTime=20 CoverDriven=1 Timer3=500 ShowStartup=1 HasIcon=1 HasCoverDriven=1 HasStartup=1 HasMustUI=1 [CaseInfo] SettingSectionName=1200 III EP DSSectionName=A4S2INFO_600 NewSetting=1 UsePrivateSettingFile=1 This file, in my case, now reads the same as before, except for a different value of 'ActiveTime'. Is that a correct setup? If I set 'LamStatus' to '0' and save that, the lamp still stays on. I have no idea what the other three settings relate to. That does not appear to be a complete setting as compared to mine. Well, I have no idea how to get there from here. But I guess that would indicate the problem is not hardware in the scanner. I don't find any file by that name (with or without its extension) on the CD for my scanner. Is it somehow generated during installation? The text I posted is NOT a new file, but part of the one you posted. mtwm.ini I'm aware of that. I would think much of that segment is not in your file of the same name due to the scanner not being detected. I simply pasted it to show you more was needed in that file besides the segment you cited. OK. Listed below is another significant portion of that file. Notice the LPT1 setting. My guess you have no such setting? Where, in my case? As I mentioned, in my case, my BIOS is set to "Bidirectional", not EPP. If your setting in CMOS is bidirectional, that should be FINE. Different computers have different settings and verbiage. It is just important that it is able to communicate both ways, and either EPP, ECP or Bidirectional will do that. [A4S2INFO_600] Language=English DSLanguage=English Brand=Mustek DSName=1200 III EP UITitle="Mustek 1200 III EP " ScanSetting=NMLSPD Version=V1.0 DriverVer=2.02 F/WVersion=None Interface=EPP/LPT1 TestMode=0 MemBufSize=256 PreScanDpi=36 PreScanWidth=306 PreScanHeight=414 TAPreScanWidth=216 TAPreScanHeight=252 PreScanFile=MSTC0000.BMP TAPreScanFile=MSTC0001.BMP X_OptiMaxRes=600 Y_OptiMaxRes=1200 WtimeTick=60 Bbricon=0 BcolorMatch=0 CMTable=A32PCM.INI SupportResCount=13 SupportRes=72 100 150 200 300 400 600 900 1200 2400 4800 7200 9600 SupportCustomRes=0 CustomRes=72 9600 ResetRes=300 ResetResIndex=4 TextMaxRes=600 TextMaxResIndex=6 SlideInstall=1 MaxBufSize=672768 When I was working as a technician years ago, we used to say we were about to call in an Indian to dance with feathers and beads when we could not figure out the solution. Needless to say we did not do that, but it is a little frustrating to have tried many things and still not have succeeded. Rest assured, that the answer is there. You just need to ask the correct question after having eliminated other potential problems. It is NOT magic!! Look at it as a challenge. I'm not really into challenges anymore. I suppose Mustek, either US or Taiwan, would really laugh if I asked them how to make one of their scanners bought in 1998 work. ;-) I couldn't find any answers to my problem on the Web anywhere. Hell, they would laugh at you right after you bought the scanner. All they wanted to do with me is sell me a scanner. Two of the shipments arrived broken and I had one hell of a time getting it straightened out. There is NO WAY they will help you with this scanner. They (SoCal, USA) did once when my lamp burnt out and I wanted to know why it had to stay on all the time. Also, once when I downloaded and installed something that indicated it was for this model but wasn't. Maybe it was this very 1999 driver that isn't working for me. Incidentally, after Murphy got loose once and a bottle fell off a shelf above this scanner and broke its glass, I had the glass replaced at a glass shop, but the double-sided tape that held it didn't work very well thereafter, particularly when I would place a heavy book over the copy in order to keep it flat (the carriage even would hang up); so I improved that flaky method of securing the glass with four screwed-down metal clips. That totally did the job. I wonder if they still use sticky tape for this purpose in Taiwan. Ray I sort of enjoy challenges, since I am retired and have time for them. Even when I was a tech, I always viewed a problem as a puzzle. It was like a game, in that the problem was hiding and my job was to find it. True, there is frustration along the way, but it is also rewarding when you succeed. You also become a LITTLE smarter in the process. Well, I got spoilt by playing design engineer. That was interesting; trying to figure out why somebody ELSE designed something some cockamany way never was fun for me. And software is pretty much however you can hack it out, and it was far too serial for my mind, even then -- and less memory-recording capability at present makes it worse. I needed to get in from the side of designs and tweak them a little (my stack was never that deep, for arbitrary stuff). Collecting the results of fixing all that arbitrary stuff isn't my idea of "smart"ness. If I were you, I would first go back to your measurements of the voltage regulators making sure of their values with respect to the scanner ground. A good place to pick up ground would be on one of the electrolytic's negative lead. Maybe I'll check that AFTER I try the original driver again, loaded exactly as per Mustek's instructions. If they measured properly, I would assume your scanner was OK. Next since it doesn't sound like you will test the parallel port, I would COMPLETELY remove the software and load it again making sure the scanner is powered up while doing so. Be sure to delete the directories created by the current load of the software, because removal of software sometimes keeps files such as INI files. That might screw up your next installation. Finally, I saw your pasting of the install log in another message, but the install log is probably of little value and hard to decipher. Try the re-installation of the software as mentioned above. Herebelow is what is presently in several files: Ray In Twain.log: ************ TWAIN_32.DLL - MESSAGE - CTwunk ::AppInitialize - Reset Log TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Starting Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Startup Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Received Startup Complete From Thunker TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Posting Close To Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Shutdown Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Received Shutdown Complete From Thunker ************ In mtwm.ini: ************ [Scanner] TwainDS=scanobj.ds ScanDll=scanobj.dll DevDll=spicall.dll FilterDLL=filter.dll UIProg=ui.exe [CaseInfo] SettingSectionName=1200 III EP DSSectionName=A4S2INFO_600 NewSetting=1 UsePrivateSettingFile=1 [A4S2INFO_600] Language=English DSLanguage=English Brand=Mustek DSName=1200 III EP UITitle="Mustek 1200 III EP " ScanSetting=NMLSPD Version=2.2 DriverVer=2.2 F/WVersion=NONE Interface=EPP/LPT2 TestMode=0 MemBufSize=256 PreScanDpi=36 PreScanWidth=306 PreScanHeight=414 TAPreScanWidth=216 TAPreScanHeight=252 PreScanFile=MSTC0000.BMP TAPreScanFile=MSTC0001.BMP X_OptiMaxRes=600 Y_OptiMaxRes=1200 WtimeTick=0 Bbricon=0 BcolorMatch=0 CMTable=A32PCM.INI SupportResCount=13 SupportRes=72 100 150 200 300 400 600 900 1200 2400 4800 7200 9600 SupportCustomRes=0 CustomRes=72 9600 ResetRes=300 ResetResIndex=4 TextMaxRes=600 TextMaxResIndex=6 SlideInstall=1 [Watch] Model=A4S2600_Watch LampStatus=1 ActiveTime=433625 GreenTime=20 CoverDriven=1 Timer3=500 ShowStartup=1 HasIcon=1 HasCoverDriven=1 HasStartup=1 HasMustUI=1 [EasyScan] Model=1200 III EP Package=cover sensor Ver=2.2 Help=C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 [Scanning Desktop] Path=C:\MSCAN\Msoffice [SupportSize] Count=3 TACount=4 ResetPaperIndex=0 PaperName=A4 A5 Letter TAPaperName=35x40mm 60x60mm 60x70mm 101x127mm A4=826 1150 A5=582 826 Letter=850 1100 35x40mm=157 137 60x60mm=236 236 60x70mm=275 236 101x127mm=500 397 [English] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [German] A4=DIN A4 A5=DIN A5 Letter=US-Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [French] A4=A*4 A5=A5 Letter=Lettre US 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Italian] A4=A4 A5=A5 Letter=Lettera 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Spanish] A4=A4 A5=A5 Letter=Carta 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Dutch] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Russian] A4=A4 A5=A5 Letter=ðÉÓØÍÏ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Chinese] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Japanese] A4=A4 A5=A5 Letter=ƒŒƒ^?[ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Simple] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Slim New UI] Language=0 ScanMode=0 ScanRes=300 ResIndex=4 PaperSize=3 Frame=0 0 306 414 Brightness=0 0 0 0 Gamma=14 14 14 10 Contrast=0 0 0 0 DpiScale=0 DeMoire=0 FilterMode=0 ColorBalance=1 ColorMatch=0 DescreenIndex=0 InRulerUnit=0 OutUnit=0 CustomRes=0 ************* In Install.log ************* *** Installation Started 1/6/5 23:48 *** Title: Source: C:\PROGRA~1\MUSTEK~2\123EP22.EXE File Copy: C:\WINDOWS\system\a4s2600.vxd Made Dir: C:\WINDOWS\TWAIN_32 Made Dir: C:\WINDOWS\TWAIN_32\A4S2_600 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\spicall.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini File Copy: C:\WINDOWS\TWAIN.DLL File Copy: C:\WINDOWS\TWAIN_32.DLL File Copy: C:\WINDOWS\TWUNK_32.EXE File Copy: C:\WINDOWS\TWUNK_16.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Free_EXE.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\filter.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\lang_e.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.ds File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\WATCH.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Lead52.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\UI.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\ABOUT.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\LOGO0601.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0001.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0000.BMP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: NewSetting INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: SettingSectionName INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: DSSectionName INI Val: A4S2INFO_600 INI Old: A4S2INFO_600 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: UsePrivateSettingFile INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: BRAND INI Val: Mustek INI Old: Mustek INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSNAME INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: UITITLE INI Val: "Mustek 1200 III EP " INI Old: Mustek 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: Version INI Val: 2.2 INI Old: V1.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DriverVer INI Val: 2.2 INI Old: 2.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: F/WVersion INI Val: NONE INI Old: None INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ScanSetting INI Val: NMLSPD INI Old: NMLSPD INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: WtimeTick INI Val: 0 INI Old: 60 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetRes INI Val: 300 INI Old: 300 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetResIndex INI Val: 4 INI Old: 4 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Model INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Package INI Val: cover sensor INI Old: cover sensor INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Ver INI Val: 2.2 INI Old: Ver1.6 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Help INI Val: C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 INI Old: C:\WINDOWS\TWAIN_32\A4S2_600\A4UI1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: Scanning Desktop INI Item: Path INI Val: C:\MSCAN\Msoffice INI Old: C:\MSCAN\Msoffice INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: Language INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: Slim New UI INI Item: Language INI Val: 0 INI Old: 0 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\a4ui1_e.hlp *********** |
#12
|
|||
|
|||
Raymond A. Chamberlin wrote:
On Thu, 06 Jan 2005 14:00:41 GMT, Ken wrote: I did a lot of clipping of old text. Well, an email request to Mostek USA (automatically, I guess) got me instructions on exactly how to pull all the twains and twunks and reinstall new ones. Apparently I didn't have to uninstall the image program bundled with the scanner, as I did before. The only significant difference I could see between what these instructions said and what I did before to remove this stuff (I still don't understand whether their term 'scanner driver' refers to all these twains and twunks or something else.) was that I didn't disable my virus auto-protect program. Rarely does the A/V program cause a problem, but if when loading software does not give you the result you want, it is a wise thing to do. Their instructions included getting a different "driver" from their Website, which I did -- '123ep22.exe', which came out in 1999. The one on my CD, that I used before, is 'd12epe22.exe'. Which one do you use? I have used both of them, and I saw no real difference. I think my current installation was from the CD. So I installed this newer "driver". I note that it leaves out the 'Twain' folder, only installing the 'Twain32' folder into the Windows folder. Isn't the 'Twain' folder just for 16=bit-word machines anyhow? Could be? I am looking at a Win 98 OS and that Dir IS there. So, OK, now I don't get a flag saying it can't detect the scanner, but I still get one that says it can't find 'twain.dll' in the Windows folder, although this file IS in the Windows folder. So I guess I'll uninstall that driver collection and reinstall the d12epe22 one per their instructions and see if that works. It is hard to say exactly why you got that message, but it sounds like it is a path problem. It could be that some remnant left behind is incorrect and it cannot find the file because it is looking in the wrong location. We can certainly forget all this discussion about when the scanner lamp should be ON though. At present, when it DOESN'T say it can't find the scanner, that light still does NOT go on and off with the tray icon; it's ALWAYS ON. If it does in your case, it must be that units having some ranges of serial do that, while others don't. I doubt that. But it doesn't matter until we get your scanner working. Then we will see if this is true. The power input at the scanner's main board measures 15 v. That is correct for the wall wart. I located two components on the main board that appeared to be power regulators. I don't know their pinouts, but the only pins that measured significant voltages other than 15 v showed 3 and 12 v, respectively. One of the outside pins (the left one if I recall correctly, but don't hold me to this) should be the input voltage. In this case, 15v. The center pin is Ground. The right terminal is the output voltage, 12v. You might not be placing your common lead of your DVM to true ground when you measured the center terminal. Sometimes these circuits do not use the same ground as your computer uses. The other regulator should work the same way, but the output should be +5v. (I think) The marking on the regulators should read something like 9805 and 9812 indicating the +5 and +12 volt output. I don't think there's any problem there. I measured with respect to the INPUT power-cable ground. I measured the +12 and +3 on different pins relative to the same physical start of pin count. The other non-15-v pins on the two regulators had very low voltages. There are no markings on the regulators. Most of the time there are, but if you say there are not, then so be it. You can generally tell what it might be by the voltage rating of the caps tied to their output. That is, if the caps are rated at 10 volts, then the output of the regulator is probably in the neighborhood of 5 volts. If the caps are rated 16-25 volts, the regulator is probably no larger than +12. Most designers place caps with voltage ratings approx. twice the voltage used on the bus. Again, I cannot say with certainty that there is an isolated ground, but I CAN assure you that the +3v is WRONG! If my memory serves me right, there is a +5 volt regulator used for the logic. The input lead was +12v if I recall, and the output MUST be +5v. The center terminal is GROUND. If it is reading +3v, then either your meter is not on the same ground plain or your ground lead has opened for the regulator. There are very few semiconductors that operate at less than 5 volts. In fact, the cut over level is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. If the software were NOT loaded properly, there should have been an error message saying that a file was not found or could not load. Nothing is 100%, but that would be the case most of the time. Whatever. Software types have no constraints. It's all seat-of-the-pants. It's all chaos to me. The text I posted is NOT a new file, but part of the one you posted. mtwm.ini I'm aware of that. I would think much of that segment is not in your file of the same name due to the scanner not being detected. I simply pasted it to show you more was needed in that file besides the segment you cited. OK. If your setting in CMOS is bidirectional, that should be FINE. Different computers have different settings and verbiage. It is just important that it is able to communicate both ways, and either EPP, ECP or Bidirectional will do that. Hell, they would laugh at you right after you bought the scanner. All they wanted to do with me is sell me a scanner. Two of the shipments arrived broken and I had one hell of a time getting it straightened out. There is NO WAY they will help you with this scanner. They (SoCal, USA) did once when my lamp burnt out and I wanted to know why it had to stay on all the time. Also, once when I downloaded and installed something that indicated it was for this model but wasn't. Maybe it was this very 1999 driver that isn't working for me. Ray I sort of enjoy challenges, since I am retired and have time for them. Even when I was a tech, I always viewed a problem as a puzzle. It was like a game, in that the problem was hiding and my job was to find it. True, there is frustration along the way, but it is also rewarding when you succeed. You also become a LITTLE smarter in the process. Well, I got spoilt by playing design engineer. That was interesting; trying to figure out why somebody ELSE designed something some cockamany way never was fun for me. And software is pretty much however you can hack it out, and it was far too serial for my mind, even then -- and less memory-recording capability at present makes it worse. I needed to get in from the side of designs and tweak them a little (my stack was never that deep, for arbitrary stuff). Collecting the results of fixing all that arbitrary stuff isn't my idea of "smart"ness. If I were you, I would first go back to your measurements of the voltage regulators making sure of their values with respect to the scanner ground. A good place to pick up ground would be on one of the electrolytic's negative lead. Maybe I'll check that AFTER I try the original driver again, loaded exactly as per Mustek's instructions. Nothing lost. I can assure you however that those measurements if measure correctly are wrong. Make sure you measure them with reference to circuit ground. Which MIGHT NOT be PS ground. If they measured properly, I would assume your scanner was OK. Next since it doesn't sound like you will test the parallel port, I would COMPLETELY remove the software and load it again making sure the scanner is powered up while doing so. Be sure to delete the directories created by the current load of the software, because removal of software sometimes keeps files such as INI files. That might screw up your next installation. Finally, I saw your pasting of the install log in another message, but the install log is probably of little value and hard to decipher. Try the re-installation of the software as mentioned above. Herebelow is what is presently in several files: Ray In Twain.log: ************ TWAIN_32.DLL - MESSAGE - CTwunk ::AppInitialize - Reset Log TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Starting Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Startup Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Received Startup Complete From Thunker TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Posting Close To Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Shutdown Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Received Shutdown Complete From Thunker ************ In mtwm.ini: ************ [Scanner] TwainDS=scanobj.ds ScanDll=scanobj.dll DevDll=spicall.dll FilterDLL=filter.dll UIProg=ui.exe [CaseInfo] SettingSectionName=1200 III EP DSSectionName=A4S2INFO_600 NewSetting=1 UsePrivateSettingFile=1 [A4S2INFO_600] Language=English DSLanguage=English Brand=Mustek DSName=1200 III EP UITitle="Mustek 1200 III EP " ScanSetting=NMLSPD Version=2.2 DriverVer=2.2 F/WVersion=NONE Interface=EPP/LPT2 TestMode=0 MemBufSize=256 PreScanDpi=36 PreScanWidth=306 PreScanHeight=414 TAPreScanWidth=216 TAPreScanHeight=252 PreScanFile=MSTC0000.BMP TAPreScanFile=MSTC0001.BMP X_OptiMaxRes=600 Y_OptiMaxRes=1200 WtimeTick=0 Bbricon=0 BcolorMatch=0 CMTable=A32PCM.INI SupportResCount=13 SupportRes=72 100 150 200 300 400 600 900 1200 2400 4800 7200 9600 SupportCustomRes=0 CustomRes=72 9600 ResetRes=300 ResetResIndex=4 TextMaxRes=600 TextMaxResIndex=6 SlideInstall=1 [Watch] Model=A4S2600_Watch LampStatus=1 ActiveTime=433625 GreenTime=20 CoverDriven=1 Timer3=500 ShowStartup=1 HasIcon=1 HasCoverDriven=1 HasStartup=1 HasMustUI=1 [EasyScan] Model=1200 III EP Package=cover sensor Ver=2.2 Help=C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 [Scanning Desktop] Path=C:\MSCAN\Msoffice [SupportSize] Count=3 TACount=4 ResetPaperIndex=0 PaperName=A4 A5 Letter TAPaperName=35x40mm 60x60mm 60x70mm 101x127mm A4=826 1150 A5=582 826 Letter=850 1100 35x40mm=157 137 60x60mm=236 236 60x70mm=275 236 101x127mm=500 397 [English] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [German] A4=DIN A4 A5=DIN A5 Letter=US-Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [French] A4=A 4 A5=A5 Letter=Lettre US 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Italian] A4=A4 A5=A5 Letter=Lettera 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Spanish] A4=A4 A5=A5 Letter=Carta 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Dutch] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Russian] A4=A4 A5=A5 Letter=ðÉÓØÍÏ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Chinese] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Japanese] A4=A4 A5=A5 Letter=ƒŒƒ^?[ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Simple] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Slim New UI] Language=0 ScanMode=0 ScanRes=300 ResIndex=4 PaperSize=3 Frame=0 0 306 414 Brightness=0 0 0 0 Gamma=14 14 14 10 Contrast=0 0 0 0 DpiScale=0 DeMoire=0 FilterMode=0 ColorBalance=1 ColorMatch=0 DescreenIndex=0 InRulerUnit=0 OutUnit=0 CustomRes=0 ************* In Install.log ************* *** Installation Started 1/6/5 23:48 *** Title: Source: C:\PROGRA~1\MUSTEK~2\123EP22.EXE File Copy: C:\WINDOWS\system\a4s2600.vxd Made Dir: C:\WINDOWS\TWAIN_32 Made Dir: C:\WINDOWS\TWAIN_32\A4S2_600 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\spicall.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini File Copy: C:\WINDOWS\TWAIN.DLL File Copy: C:\WINDOWS\TWAIN_32.DLL File Copy: C:\WINDOWS\TWUNK_32.EXE File Copy: C:\WINDOWS\TWUNK_16.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Free_EXE.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\filter.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\lang_e.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.ds File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\WATCH.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Lead52.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\UI.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\ABOUT.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\LOGO0601.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0001.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0000.BMP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: NewSetting INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: SettingSectionName INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: DSSectionName INI Val: A4S2INFO_600 INI Old: A4S2INFO_600 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: UsePrivateSettingFile INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: BRAND INI Val: Mustek INI Old: Mustek INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSNAME INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: UITITLE INI Val: "Mustek 1200 III EP " INI Old: Mustek 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: Version INI Val: 2.2 INI Old: V1.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DriverVer INI Val: 2.2 INI Old: 2.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: F/WVersion INI Val: NONE INI Old: None INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ScanSetting INI Val: NMLSPD INI Old: NMLSPD INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: WtimeTick INI Val: 0 INI Old: 60 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetRes INI Val: 300 INI Old: 300 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetResIndex INI Val: 4 INI Old: 4 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Model INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Package INI Val: cover sensor INI Old: cover sensor INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Ver INI Val: 2.2 INI Old: Ver1.6 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Help INI Val: C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 INI Old: C:\WINDOWS\TWAIN_32\A4S2_600\A4UI1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: Scanning Desktop INI Item: Path INI Val: C:\MSCAN\Msoffice INI Old: C:\MSCAN\Msoffice INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: Language INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: Slim New UI INI Item: Language INI Val: 0 INI Old: 0 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\a4ui1_e.hlp *********** To be honest with you, it is difficult to decipher exactly what all that means. I will attempt after you take your voltage readings and they prove correct. Error messages don't mean much if the hardware does not work. |
#13
|
|||
|
|||
Top post because of so "stuff".
Your TWAIN.LOG shows that the TWAIN interface worked correctly. I woud guess that the software is working and you have a hardware problem with the scanner. One other thing, If you have any virus software on your computer, Disable it and remove all previous attempts to install. Then Install the software again without the virus scanner running. -- CSM1 http://www.carlmcmillan.com -- "Ken" wrote in message ... Raymond A. Chamberlin wrote: On Thu, 06 Jan 2005 14:00:41 GMT, Ken wrote: I did a lot of clipping of old text. Well, an email request to Mostek USA (automatically, I guess) got me instructions on exactly how to pull all the twains and twunks and reinstall new ones. Apparently I didn't have to uninstall the image program bundled with the scanner, as I did before. The only significant difference I could see between what these instructions said and what I did before to remove this stuff (I still don't understand whether their term 'scanner driver' refers to all these twains and twunks or something else.) was that I didn't disable my virus auto-protect program. Rarely does the A/V program cause a problem, but if when loading software does not give you the result you want, it is a wise thing to do. Their instructions included getting a different "driver" from their Website, which I did -- '123ep22.exe', which came out in 1999. The one on my CD, that I used before, is 'd12epe22.exe'. Which one do you use? I have used both of them, and I saw no real difference. I think my current installation was from the CD. So I installed this newer "driver". I note that it leaves out the 'Twain' folder, only installing the 'Twain32' folder into the Windows folder. Isn't the 'Twain' folder just for 16=bit-word machines anyhow? Could be? I am looking at a Win 98 OS and that Dir IS there. So, OK, now I don't get a flag saying it can't detect the scanner, but I still get one that says it can't find 'twain.dll' in the Windows folder, although this file IS in the Windows folder. So I guess I'll uninstall that driver collection and reinstall the d12epe22 one per their instructions and see if that works. It is hard to say exactly why you got that message, but it sounds like it is a path problem. It could be that some remnant left behind is incorrect and it cannot find the file because it is looking in the wrong location. We can certainly forget all this discussion about when the scanner lamp should be ON though. At present, when it DOESN'T say it can't find the scanner, that light still does NOT go on and off with the tray icon; it's ALWAYS ON. If it does in your case, it must be that units having some ranges of serial do that, while others don't. I doubt that. But it doesn't matter until we get your scanner working. Then we will see if this is true. The power input at the scanner's main board measures 15 v. That is correct for the wall wart. I located two components on the main board that appeared to be power regulators. I don't know their pinouts, but the only pins that measured significant voltages other than 15 v showed 3 and 12 v, respectively. One of the outside pins (the left one if I recall correctly, but don't hold me to this) should be the input voltage. In this case, 15v. The center pin is Ground. The right terminal is the output voltage, 12v. You might not be placing your common lead of your DVM to true ground when you measured the center terminal. Sometimes these circuits do not use the same ground as your computer uses. The other regulator should work the same way, but the output should be +5v. (I think) The marking on the regulators should read something like 9805 and 9812 indicating the +5 and +12 volt output. I don't think there's any problem there. I measured with respect to the INPUT power-cable ground. I measured the +12 and +3 on different pins relative to the same physical start of pin count. The other non-15-v pins on the two regulators had very low voltages. There are no markings on the regulators. Most of the time there are, but if you say there are not, then so be it. You can generally tell what it might be by the voltage rating of the caps tied to their output. That is, if the caps are rated at 10 volts, then the output of the regulator is probably in the neighborhood of 5 volts. If the caps are rated 16-25 volts, the regulator is probably no larger than +12. Most designers place caps with voltage ratings approx. twice the voltage used on the bus. Again, I cannot say with certainty that there is an isolated ground, but I CAN assure you that the +3v is WRONG! If my memory serves me right, there is a +5 volt regulator used for the logic. The input lead was +12v if I recall, and the output MUST be +5v. The center terminal is GROUND. If it is reading +3v, then either your meter is not on the same ground plain or your ground lead has opened for the regulator. There are very few semiconductors that operate at less than 5 volts. In fact, the cut over level is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. If the software were NOT loaded properly, there should have been an error message saying that a file was not found or could not load. Nothing is 100%, but that would be the case most of the time. Whatever. Software types have no constraints. It's all seat-of-the-pants. It's all chaos to me. The text I posted is NOT a new file, but part of the one you posted. mtwm.ini I'm aware of that. I would think much of that segment is not in your file of the same name due to the scanner not being detected. I simply pasted it to show you more was needed in that file besides the segment you cited. OK. If your setting in CMOS is bidirectional, that should be FINE. Different computers have different settings and verbiage. It is just important that it is able to communicate both ways, and either EPP, ECP or Bidirectional will do that. Hell, they would laugh at you right after you bought the scanner. All they wanted to do with me is sell me a scanner. Two of the shipments arrived broken and I had one hell of a time getting it straightened out. There is NO WAY they will help you with this scanner. They (SoCal, USA) did once when my lamp burnt out and I wanted to know why it had to stay on all the time. Also, once when I downloaded and installed something that indicated it was for this model but wasn't. Maybe it was this very 1999 driver that isn't working for me. Ray I sort of enjoy challenges, since I am retired and have time for them. Even when I was a tech, I always viewed a problem as a puzzle. It was like a game, in that the problem was hiding and my job was to find it. True, there is frustration along the way, but it is also rewarding when you succeed. You also become a LITTLE smarter in the process. Well, I got spoilt by playing design engineer. That was interesting; trying to figure out why somebody ELSE designed something some cockamany way never was fun for me. And software is pretty much however you can hack it out, and it was far too serial for my mind, even then -- and less memory-recording capability at present makes it worse. I needed to get in from the side of designs and tweak them a little (my stack was never that deep, for arbitrary stuff). Collecting the results of fixing all that arbitrary stuff isn't my idea of "smart"ness. If I were you, I would first go back to your measurements of the voltage regulators making sure of their values with respect to the scanner ground. A good place to pick up ground would be on one of the electrolytic's negative lead. Maybe I'll check that AFTER I try the original driver again, loaded exactly as per Mustek's instructions. Nothing lost. I can assure you however that those measurements if measure correctly are wrong. Make sure you measure them with reference to circuit ground. Which MIGHT NOT be PS ground. If they measured properly, I would assume your scanner was OK. Next since it doesn't sound like you will test the parallel port, I would COMPLETELY remove the software and load it again making sure the scanner is powered up while doing so. Be sure to delete the directories created by the current load of the software, because removal of software sometimes keeps files such as INI files. That might screw up your next installation. Finally, I saw your pasting of the install log in another message, but the install log is probably of little value and hard to decipher. Try the re-installation of the software as mentioned above. Herebelow is what is presently in several files: Ray In Twain.log: ************ TWAIN_32.DLL - MESSAGE - CTwunk ::AppInitialize - Reset Log TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Starting Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Startup Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Received Startup Complete From Thunker TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Posting Close To Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Shutdown Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Received Shutdown Complete From Thunker ************ In mtwm.ini: ************ [Scanner] TwainDS=scanobj.ds ScanDll=scanobj.dll DevDll=spicall.dll FilterDLL=filter.dll UIProg=ui.exe [CaseInfo] SettingSectionName=1200 III EP DSSectionName=A4S2INFO_600 NewSetting=1 UsePrivateSettingFile=1 [A4S2INFO_600] Language=English DSLanguage=English Brand=Mustek DSName=1200 III EP UITitle="Mustek 1200 III EP " ScanSetting=NMLSPD Version=2.2 DriverVer=2.2 F/WVersion=NONE Interface=EPP/LPT2 TestMode=0 MemBufSize=256 PreScanDpi=36 PreScanWidth=306 PreScanHeight=414 TAPreScanWidth=216 TAPreScanHeight=252 PreScanFile=MSTC0000.BMP TAPreScanFile=MSTC0001.BMP X_OptiMaxRes=600 Y_OptiMaxRes=1200 WtimeTick=0 Bbricon=0 BcolorMatch=0 CMTable=A32PCM.INI SupportResCount=13 SupportRes=72 100 150 200 300 400 600 900 1200 2400 4800 7200 9600 SupportCustomRes=0 CustomRes=72 9600 ResetRes=300 ResetResIndex=4 TextMaxRes=600 TextMaxResIndex=6 SlideInstall=1 [Watch] Model=A4S2600_Watch LampStatus=1 ActiveTime=433625 GreenTime=20 CoverDriven=1 Timer3=500 ShowStartup=1 HasIcon=1 HasCoverDriven=1 HasStartup=1 HasMustUI=1 [EasyScan] Model=1200 III EP Package=cover sensor Ver=2.2 Help=C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 [Scanning Desktop] Path=C:\MSCAN\Msoffice [SupportSize] Count=3 TACount=4 ResetPaperIndex=0 PaperName=A4 A5 Letter TAPaperName=35x40mm 60x60mm 60x70mm 101x127mm A4=826 1150 A5=582 826 Letter=850 1100 35x40mm=157 137 60x60mm=236 236 60x70mm=275 236 101x127mm=500 397 [English] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [German] A4=DIN A4 A5=DIN A5 Letter=US-Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [French] A4=A 4 A5=A5 Letter=Lettre US 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Italian] A4=A4 A5=A5 Letter=Lettera 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Spanish] A4=A4 A5=A5 Letter=Carta 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Dutch] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Russian] A4=A4 A5=A5 Letter=ðÉÓØÍÏ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Chinese] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Japanese] A4=A4 A5=A5 Letter=ƒŒƒ^?[ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Simple] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Slim New UI] Language=0 ScanMode=0 ScanRes=300 ResIndex=4 PaperSize=3 Frame=0 0 306 414 Brightness=0 0 0 0 Gamma=14 14 14 10 Contrast=0 0 0 0 DpiScale=0 DeMoire=0 FilterMode=0 ColorBalance=1 ColorMatch=0 DescreenIndex=0 InRulerUnit=0 OutUnit=0 CustomRes=0 ************* In Install.log ************* *** Installation Started 1/6/5 23:48 *** Title: Source: C:\PROGRA~1\MUSTEK~2\123EP22.EXE File Copy: C:\WINDOWS\system\a4s2600.vxd Made Dir: C:\WINDOWS\TWAIN_32 Made Dir: C:\WINDOWS\TWAIN_32\A4S2_600 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\spicall.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini File Copy: C:\WINDOWS\TWAIN.DLL File Copy: C:\WINDOWS\TWAIN_32.DLL File Copy: C:\WINDOWS\TWUNK_32.EXE File Copy: C:\WINDOWS\TWUNK_16.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Free_EXE.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\filter.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\lang_e.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.ds File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\WATCH.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Lead52.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\UI.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\ABOUT.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\LOGO0601.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0001.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0000.BMP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: NewSetting INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: SettingSectionName INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: DSSectionName INI Val: A4S2INFO_600 INI Old: A4S2INFO_600 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: UsePrivateSettingFile INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: BRAND INI Val: Mustek INI Old: Mustek INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSNAME INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: UITITLE INI Val: "Mustek 1200 III EP " INI Old: Mustek 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: Version INI Val: 2.2 INI Old: V1.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DriverVer INI Val: 2.2 INI Old: 2.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: F/WVersion INI Val: NONE INI Old: None INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ScanSetting INI Val: NMLSPD INI Old: NMLSPD INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: WtimeTick INI Val: 0 INI Old: 60 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetRes INI Val: 300 INI Old: 300 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetResIndex INI Val: 4 INI Old: 4 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Model INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Package INI Val: cover sensor INI Old: cover sensor INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Ver INI Val: 2.2 INI Old: Ver1.6 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Help INI Val: C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 INI Old: C:\WINDOWS\TWAIN_32\A4S2_600\A4UI1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: Scanning Desktop INI Item: Path INI Val: C:\MSCAN\Msoffice INI Old: C:\MSCAN\Msoffice INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: Language INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: Slim New UI INI Item: Language INI Val: 0 INI Old: 0 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\a4ui1_e.hlp *********** To be honest with you, it is difficult to decipher exactly what all that means. I will attempt after you take your voltage readings and they prove correct. Error messages don't mean much if the hardware does not work. |
#14
|
|||
|
|||
Ken wrote:
Raymond A. Chamberlin wrote: On Thu, 06 Jan 2005 14:00:41 GMT, Ken wrote: I did a lot of clipping of old text. Well, an email request to Mostek USA (automatically, I guess) got me instructions on exactly how to pull all the twains and twunks and reinstall new ones. Apparently I didn't have to uninstall the image program bundled with the scanner, as I did before. The only significant difference I could see between what these instructions said and what I did before to remove this stuff (I still don't understand whether their term 'scanner driver' refers to all these twains and twunks or something else.) was that I didn't disable my virus auto-protect program. Rarely does the A/V program cause a problem, but if when loading software does not give you the result you want, it is a wise thing to do. Their instructions included getting a different "driver" from their Website, which I did -- '123ep22.exe', which came out in 1999. The one on my CD, that I used before, is 'd12epe22.exe'. Which one do you use? I have used both of them, and I saw no real difference. I think my current installation was from the CD. So I installed this newer "driver". I note that it leaves out the 'Twain' folder, only installing the 'Twain32' folder into the Windows folder. Isn't the 'Twain' folder just for 16=bit-word machines anyhow? Could be? I am looking at a Win 98 OS and that Dir IS there. So, OK, now I don't get a flag saying it can't detect the scanner, but I still get one that says it can't find 'twain.dll' in the Windows folder, although this file IS in the Windows folder. So I guess I'll uninstall that driver collection and reinstall the d12epe22 one per their instructions and see if that works. It is hard to say exactly why you got that message, but it sounds like it is a path problem. It could be that some remnant left behind is incorrect and it cannot find the file because it is looking in the wrong location. We can certainly forget all this discussion about when the scanner lamp should be ON though. At present, when it DOESN'T say it can't find the scanner, that light still does NOT go on and off with the tray icon; it's ALWAYS ON. If it does in your case, it must be that units having some ranges of serial do that, while others don't. I doubt that. But it doesn't matter until we get your scanner working. Then we will see if this is true. The power input at the scanner's main board measures 15 v. That is correct for the wall wart. I located two components on the main board that appeared to be power regulators. I don't know their pinouts, but the only pins that measured significant voltages other than 15 v showed 3 and 12 v, respectively. One of the outside pins (the left one if I recall correctly, but don't hold me to this) should be the input voltage. In this case, 15v. The center pin is Ground. The right terminal is the output voltage, 12v. You might not be placing your common lead of your DVM to true ground when you measured the center terminal. Sometimes these circuits do not use the same ground as your computer uses. The other regulator should work the same way, but the output should be +5v. (I think) The marking on the regulators should read something like 9805 and 9812 indicating the +5 and +12 volt output. I don't think there's any problem there. I measured with respect to the INPUT power-cable ground. I measured the +12 and +3 on different pins relative to the same physical start of pin count. The other non-15-v pins on the two regulators had very low voltages. There are no markings on the regulators. Most of the time there are, but if you say there are not, then so be it. You can generally tell what it might be by the voltage rating of the caps tied to their output. That is, if the caps are rated at 10 volts, then the output of the regulator is probably in the neighborhood of 5 volts. If the caps are rated 16-25 volts, the regulator is probably no larger than +12. Most designers place caps with voltage ratings approx. twice the voltage used on the bus. Again, I cannot say with certainty that there is an isolated ground, but I CAN assure you that the +3v is WRONG! If my memory serves me right, there is a +5 volt regulator used for the logic. The input lead was +12v if I recall, and the output MUST be +5v. The center terminal is GROUND. If it is reading +3v, then either your meter is not on the same ground plain or your ground lead has opened for the regulator. There are very few semiconductors that operate at less than 5 volts. In fact, the cut over level is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. Here is a link for a graphic of the type regulator I believe is in the scanner. http://www.nteinc.com/specs/900to999/pdf/nte960.pdf I was wrong about the 9805 number, it is a 7805. (Had another brain fart.) Notice however that the input voltage is on the left of the device, ground is the center terminal, and the output is the left terminal. If the software were NOT loaded properly, there should have been an error message saying that a file was not found or could not load. Nothing is 100%, but that would be the case most of the time. Whatever. Software types have no constraints. It's all seat-of-the-pants. It's all chaos to me. The text I posted is NOT a new file, but part of the one you posted. mtwm.ini I'm aware of that. I would think much of that segment is not in your file of the same name due to the scanner not being detected. I simply pasted it to show you more was needed in that file besides the segment you cited. OK. If your setting in CMOS is bidirectional, that should be FINE. Different computers have different settings and verbiage. It is just important that it is able to communicate both ways, and either EPP, ECP or Bidirectional will do that. Hell, they would laugh at you right after you bought the scanner. All they wanted to do with me is sell me a scanner. Two of the shipments arrived broken and I had one hell of a time getting it straightened out. There is NO WAY they will help you with this scanner. They (SoCal, USA) did once when my lamp burnt out and I wanted to know why it had to stay on all the time. Also, once when I downloaded and installed something that indicated it was for this model but wasn't. Maybe it was this very 1999 driver that isn't working for me. Ray I sort of enjoy challenges, since I am retired and have time for them. Even when I was a tech, I always viewed a problem as a puzzle. It was like a game, in that the problem was hiding and my job was to find it. True, there is frustration along the way, but it is also rewarding when you succeed. You also become a LITTLE smarter in the process. Well, I got spoilt by playing design engineer. That was interesting; trying to figure out why somebody ELSE designed something some cockamany way never was fun for me. And software is pretty much however you can hack it out, and it was far too serial for my mind, even then -- and less memory-recording capability at present makes it worse. I needed to get in from the side of designs and tweak them a little (my stack was never that deep, for arbitrary stuff). Collecting the results of fixing all that arbitrary stuff isn't my idea of "smart"ness. If I were you, I would first go back to your measurements of the voltage regulators making sure of their values with respect to the scanner ground. A good place to pick up ground would be on one of the electrolytic's negative lead. Maybe I'll check that AFTER I try the original driver again, loaded exactly as per Mustek's instructions. Nothing lost. I can assure you however that those measurements if measure correctly are wrong. Make sure you measure them with reference to circuit ground. Which MIGHT NOT be PS ground. If they measured properly, I would assume your scanner was OK. Next since it doesn't sound like you will test the parallel port, I would COMPLETELY remove the software and load it again making sure the scanner is powered up while doing so. Be sure to delete the directories created by the current load of the software, because removal of software sometimes keeps files such as INI files. That might screw up your next installation. Finally, I saw your pasting of the install log in another message, but the install log is probably of little value and hard to decipher. Try the re-installation of the software as mentioned above. Herebelow is what is presently in several files: Ray In Twain.log: ************ TWAIN_32.DLL - MESSAGE - CTwunk ::AppInitialize - Reset Log TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Starting Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Startup Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::OpenServer - Received Startup Complete From Thunker TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Posting Close To Thunker TWUNK_16.EXE - MESSAGE - Twunk --WinMain - Posting Shutdown Complete To Twain TWAIN_32.DLL - MESSAGE - CTwunk ::CloseServer - Received Shutdown Complete From Thunker ************ In mtwm.ini: ************ [Scanner] TwainDS=scanobj.ds ScanDll=scanobj.dll DevDll=spicall.dll FilterDLL=filter.dll UIProg=ui.exe [CaseInfo] SettingSectionName=1200 III EP DSSectionName=A4S2INFO_600 NewSetting=1 UsePrivateSettingFile=1 [A4S2INFO_600] Language=English DSLanguage=English Brand=Mustek DSName=1200 III EP UITitle="Mustek 1200 III EP " ScanSetting=NMLSPD Version=2.2 DriverVer=2.2 F/WVersion=NONE Interface=EPP/LPT2 TestMode=0 MemBufSize=256 PreScanDpi=36 PreScanWidth=306 PreScanHeight=414 TAPreScanWidth=216 TAPreScanHeight=252 PreScanFile=MSTC0000.BMP TAPreScanFile=MSTC0001.BMP X_OptiMaxRes=600 Y_OptiMaxRes=1200 WtimeTick=0 Bbricon=0 BcolorMatch=0 CMTable=A32PCM.INI SupportResCount=13 SupportRes=72 100 150 200 300 400 600 900 1200 2400 4800 7200 9600 SupportCustomRes=0 CustomRes=72 9600 ResetRes=300 ResetResIndex=4 TextMaxRes=600 TextMaxResIndex=6 SlideInstall=1 [Watch] Model=A4S2600_Watch LampStatus=1 ActiveTime=433625 GreenTime=20 CoverDriven=1 Timer3=500 ShowStartup=1 HasIcon=1 HasCoverDriven=1 HasStartup=1 HasMustUI=1 [EasyScan] Model=1200 III EP Package=cover sensor Ver=2.2 Help=C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 [Scanning Desktop] Path=C:\MSCAN\Msoffice [SupportSize] Count=3 TACount=4 ResetPaperIndex=0 PaperName=A4 A5 Letter TAPaperName=35x40mm 60x60mm 60x70mm 101x127mm A4=826 1150 A5=582 826 Letter=850 1100 35x40mm=157 137 60x60mm=236 236 60x70mm=275 236 101x127mm=500 397 [English] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [German] A4=DIN A4 A5=DIN A5 Letter=US-Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [French] A4=A 4 A5=A5 Letter=Lettre US 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Italian] A4=A4 A5=A5 Letter=Lettera 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Spanish] A4=A4 A5=A5 Letter=Carta 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Dutch] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Russian] A4=A4 A5=A5 Letter=ðÉÓØÍÏ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Chinese] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Japanese] A4=A4 A5=A5 Letter=ƒŒƒ^?[ 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Simple] A4=A4 A5=A5 Letter=Letter 35x40mm=35x40mm 60x60mm=60x60mm 60x70mm=60x70mm 101x127mm=101x127mm [Slim New UI] Language=0 ScanMode=0 ScanRes=300 ResIndex=4 PaperSize=3 Frame=0 0 306 414 Brightness=0 0 0 0 Gamma=14 14 14 10 Contrast=0 0 0 0 DpiScale=0 DeMoire=0 FilterMode=0 ColorBalance=1 ColorMatch=0 DescreenIndex=0 InRulerUnit=0 OutUnit=0 CustomRes=0 ************* In Install.log ************* *** Installation Started 1/6/5 23:48 *** Title: Source: C:\PROGRA~1\MUSTEK~2\123EP22.EXE File Copy: C:\WINDOWS\system\a4s2600.vxd Made Dir: C:\WINDOWS\TWAIN_32 Made Dir: C:\WINDOWS\TWAIN_32\A4S2_600 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\spicall.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini File Copy: C:\WINDOWS\TWAIN.DLL File Copy: C:\WINDOWS\TWAIN_32.DLL File Copy: C:\WINDOWS\TWUNK_32.EXE File Copy: C:\WINDOWS\TWUNK_16.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Free_EXE.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\filter.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\lang_e.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Scanobj.ds File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\WATCH.exe File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\Lead52.dll File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\UI.EXE File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\ABOUT.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\LOGO0601.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0001.BMP File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\MSTC0000.BMP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: NewSetting INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: SettingSectionName INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: DSSectionName INI Val: A4S2INFO_600 INI Old: A4S2INFO_600 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: CaseInfo INI Item: UsePrivateSettingFile INI Val: 1 INI Old: 1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: BRAND INI Val: Mustek INI Old: Mustek INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DSNAME INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: UITITLE INI Val: "Mustek 1200 III EP " INI Old: Mustek 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: Version INI Val: 2.2 INI Old: V1.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: DriverVer INI Val: 2.2 INI Old: 2.0 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: F/WVersion INI Val: NONE INI Old: None INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ScanSetting INI Val: NMLSPD INI Old: NMLSPD INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: WtimeTick INI Val: 0 INI Old: 60 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetRes INI Val: 300 INI Old: 300 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: A4S2INFO_600 INI Item: ResetResIndex INI Val: 4 INI Old: 4 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Model INI Val: 1200 III EP INI Old: 1200 III EP INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Package INI Val: cover sensor INI Old: cover sensor INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Ver INI Val: 2.2 INI Old: Ver1.6 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: EasyScan INI Item: Help INI Val: C:\WINDOWS\TWAIN_32\A4S2_600\A4ui1 INI Old: C:\WINDOWS\TWAIN_32\A4S2_600\A4UI1 INI File: C:\WINDOWS\TWAIN_32\A4S2_600\MTWM.INI INI Sect: Scanning Desktop INI Item: Path INI Val: C:\MSCAN\Msoffice INI Old: C:\MSCAN\Msoffice INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: Language INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: A4S2INFO_600 INI Item: DSLanguage INI Val: English INI Old: English INI File: C:\WINDOWS\TWAIN_32\A4S2_600\mtwm.ini INI Sect: Slim New UI INI Item: Language INI Val: 0 INI Old: 0 File Copy: C:\WINDOWS\TWAIN_32\A4S2_600\a4ui1_e.hlp *********** To be honest with you, it is difficult to decipher exactly what all that means. I will attempt after you take your voltage readings and they prove correct. Error messages don't mean much if the hardware does not work. |
#15
|
|||
|
|||
To Ken and CSM1: See interleaved below:
On Fri, 07 Jan 2005 20:29:51 GMT, Ken wrote: Ken wrote: Raymond A. Chamberlin wrote: On Thu, 06 Jan 2005 14:00:41 GMT, Ken wrote: I did a lot of clipping of old text. Well, an email request to Mostek USA (automatically, I guess) got me instructions on exactly how to pull all the twains and twunks and reinstall new ones. Apparently I didn't have to uninstall the image program bundled with the scanner, as I did before. The only significant difference I could see between what these instructions said and what I did before to remove this stuff (I still don't understand whether their term 'scanner driver' refers to all these twains and twunks or something else.) was that I didn't disable my virus auto-protect program. Rarely does the A/V program cause a problem, but if when loading software does not give you the result you want, it is a wise thing to do. Their instructions included getting a different "driver" from their Website, which I did -- '123ep22.exe', which came out in 1999. The one on my CD, that I used before, is 'd12epe22.exe'. Which one do you use? I have used both of them, and I saw no real difference. I think my current installation was from the CD. Yes, the one from the CD does the same thing now -- asks for twain.dll but no other flags. So I installed this newer "driver". I note that it leaves out the 'Twain' folder, only installing the 'Twain32' folder into the Windows folder. Isn't the 'Twain' folder just for 16=bit-word machines anyhow? Could be? I am looking at a Win 98 OS and that Dir IS there. Well the CD allows one to set the scanner up for Win 3.1 alternatively. So, OK, now I don't get a flag saying it can't detect the scanner, but I still get one that says it can't find 'twain.dll' in the Windows folder, although this file IS in the Windows folder. So I guess I'll uninstall that driver collection and reinstall the d12epe22 one per their instructions and see if that works. It is hard to say exactly why you got that message, but it sounds like it is a path problem. It could be that some remnant left behind is incorrect and it cannot find the file because it is looking in the wrong location. We can certainly forget all this discussion about when the scanner lamp should be ON though. At present, when it DOESN'T say it can't find the scanner, that light still does NOT go on and off with the tray icon; it's ALWAYS ON. If it does in your case, it must be that units having some ranges of serial do that, while others don't. I doubt that. But it doesn't matter until we get your scanner working. Then we will see if this is true. The power input at the scanner's main board measures 15 v. That is correct for the wall wart. I located two components on the main board that appeared to be power regulators. I don't know their pinouts, but the only pins that measured significant voltages other than 15 v showed 3 and 12 v, respectively. One of the outside pins (the left one if I recall correctly, but don't hold me to this) should be the input voltage. In this case, 15v. The center pin is Ground. The right terminal is the output voltage, 12v. You might not be placing your common lead of your DVM to true ground when you measured the center terminal. Sometimes these circuits do not use the same ground as your computer uses. The other regulator should work the same way, but the output should be +5v. (I think) The marking on the regulators should read something like 9805 and 9812 indicating the +5 and +12 volt output. I don't think there's any problem there. I measured with respect to the INPUT power-cable ground. I measured the +12 and +3 on different pins relative to the same physical start of pin count. The other non-15-v pins on the two regulators had very low voltages. There are no markings on the regulators. Most of the time there are, but if you say there are not, then so be it. My bad. [red-face emoticon] 7805 and 7812; see above. Not the first time I've been a bad tech. I could blame my glaucoma, but it was really lack of ambition to get the right tools. You can generally tell what it might be by the voltage rating of the caps tied to their output. That is, if the caps are rated at 10 volts, then the output of the regulator is probably in the neighborhood of 5 volts. If the caps are rated 16-25 volts, the regulator is probably no larger than +12. Most designers place caps with voltage ratings approx. twice the voltage used on the bus. Again, I cannot say with certainty that there is an isolated ground, but I CAN assure you that the +3v is WRONG! If my memory serves me right, there is a +5 volt regulator used for the logic. The input lead was +12v if I recall, and the output MUST be +5v. The center terminal is GROUND. If it is reading +3v, then either your meter is not on the same ground plain or your ground lead has opened for the regulator. The 12-v regulator is OK -- +15 v in, +12 v out. The 5-v regulator reads thus: +15 v --11-ohm/2(?)-w res--o--REG--o---- +0.5 v | | 47 µ / 25v 100 µ / 10 v | | gnd gnd The above circuit may be rather scrambled when you get it. Hope not. The aluminum electrolytics, the regular and the resistor are all quite hot, as is a nearby AIC 1563CN high-efficiency DC/DC converter. ( http://www.scaner.by.ru/data.htm if your Russian is fluent. ) So I'm not sure how many of these components are bad. Maybe just the output electrolytic? Possibly something on beyond that. I can't find those caps in my junk box, so I'll hit Radio Shack tomorrow. There are very few semiconductors that operate at less than 5 volts. Well, I guess any of that vintage. But there certainly are now a lot that run on 3 v or so. In fact, the cut over level What is that? is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. Yes. Here is a link for a graphic of the type regulator I believe is in the scanner. http://www.nteinc.com/specs/900to999/pdf/nte960.pdf I was wrong about the 9805 number, it is a 7805. (Had another brain fart.) Notice however that the input voltage is on the left of the device, ground is the center terminal, and the output is the left terminal. Yes, you're right, a 7805 and a 7812. With the board out where I can get a flashlight on the regulators at just the right angle, and using a magnifying glass, I can read these old conventional numbers of positive voltage regulators on them. SNIP |
#16
|
|||
|
|||
Raymond A. Chamberlin wrote:
To Ken and CSM1: See interleaved below: On Fri, 07 Jan 2005 20:29:51 GMT, Ken wrote: The 12-v regulator is OK -- +15 v in, +12 v out. The 5-v regulator reads thus: +15 v --11-ohm/2(?)-w res--o--REG--o---- +0.5 v | | 47 µ / 25v 100 µ / 10 v | | gnd gnd The above circuit may be rather scrambled when you get it. Hope not. Ray, I am not sure I am reading your drawing correctly, but if you mean you have .5 volts on the output, THAT IS A PROBLEM. The aluminum electrolytics, the regular and the resistor are all quite hot, as is a nearby AIC 1563CN high-efficiency DC/DC converter. It will be very difficult to replace any of the logic circuits attached to this +5 volt bus, but it is possible that a cap is leaking drawing down your +5 volts. More likely, the regulator failed, but the only way to tell is to lift some leads. I would first lift the output from the regulator and measure it. If it is +5, then the problem is on the bus. Using an Ohm meter and lifting leads from caps would be the next easiest, then attack the other components if you choose. For what it is worth, I repaired one of these scanners by replacing the +5 regulator. Of course your results may vary!!! ( http://www.scaner.by.ru/data.htm if your Russian is fluent. ) So I'm not sure how many of these components are bad. Maybe just the output electrolytic? Possibly something on beyond that. I can't find those caps in my junk box, so I'll hit Radio Shack tomorrow. Remember, if you do find it to be an electrolytic, you can replace it with any voltage larger than the one installed and any capacitance larger than the one installed. It is only a filter, so the capacitance is NOT critical. Needless to say, observe the polarity. There are very few semiconductors that operate at less than 5 volts. Well, I guess any of that vintage. But there certainly are now a lot that run on 3 v or so. There are, but they generally are more expensive than the +5 volt variety. As circuits are designed to operate on lower voltages, they are becoming more popular. This in turn causes them to become cheaper. In fact, the cut over level What is that? It really becomes quite involved to explain, but simply stated, the circuits are designed so that stray noise does NOT trigger them. Since noise is unavoidable in most cases, the threshold is designed so that only a signal over .6 volts will switch on a semiconductor. Therefore, most of the time a signal of less than .6 volts is considered a zero, and one greater than 1.6 is considered a one. The area in between these levels were referred in my day as "No man's land." That is, the result of such a voltage was not certain on a circuit. One could turn on, while another might not. Disclaimer: News groups are famous for some person who has little to contribute to a topic jumping in to contradict what another has said. The topic of logic circuits is long and complex. It also has many exceptions, and that is why I even hesitate to start to explain the cross over level topic. I DO NOT HAVE ALL THE ANSWERS!!! Perhaps this might negate the need for someone to blast me??? is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. Yes. Here is a link for a graphic of the type regulator I believe is in the scanner. http://www.nteinc.com/specs/900to999/pdf/nte960.pdf I was wrong about the 9805 number, it is a 7805. (Had another brain fart.) Notice however that the input voltage is on the left of the device, ground is the center terminal, and the output is the left terminal. Yes, you're right, a 7805 and a 7812. With the board out where I can get a flashlight on the regulators at just the right angle, and using a magnifying glass, I can read these old conventional numbers of positive voltage regulators on them. SNIP |
#17
|
|||
|
|||
On Sat, 08 Jan 2005 13:45:07 GMT, Ken wrote:
Raymond A. Chamberlin wrote: To Ken and CSM1: See interleaved below: On Fri, 07 Jan 2005 20:29:51 GMT, Ken wrote: The 12-v regulator is OK -- +15 v in, +12 v out. The 5-v regulator reads thus: +15 v --11-ohm/2(?)-w res--o--REG--o---- +0.5 v | | 47 µ / 25v 100 µ / 10 v | | gnd gnd The above circuit may be rather scrambled when you get it. Hope not. Ray, I am not sure I am reading your drawing correctly, but if you mean you have .5 volts on the output, THAT IS A PROBLEM. Yes, that's what I mean. And yes, that obviously is a problem. The aluminum electrolytics, the regular and the resistor are all quite hot, as is a nearby AIC 1563CN high-efficiency DC/DC converter. It will be very difficult to replace any of the logic circuits attached to this +5 volt bus, but it is possible that a cap is leaking drawing down your +5 volts. More likely, the regulator failed, but the only way to tell is to lift some leads. I would first lift the output from the regulator and measure it. If it is +5, then the problem is on the bus. Using an Ohm meter and lifting leads from caps would be the next easiest, then attack the other components if you choose. For what it is worth, I repaired one of these scanners by replacing the +5 regulator. Of course your results may vary!!! Well, I overlooked a pair of tiny chip/surface-mount components on the other side of the board, one on each side of the regulator to ground. I would conclude they're either diodes or electrolytics. Do they suppress high-frequency oscillations? They came after my time-in-grade. Anyhow, I yanked the two radial-lead caps and the regulator. All of those appear fine -- as far as I can tell with a 20,000-ohm/v ohmmeter. The chip jobby on the regulator input reads 3.3 ohm one way and 20 ohms the other way (on the 20-ohms-at-center scale. The one on the regulator output reads a dead short both ways on the same scale. I assume the latter ist kaputt. Now, how the devil would I be able to find out the specs of that component -- unless -- ha, ha -- Mostek will tell me? Hey maybe they would send me a whole schematic. . .so I could tell them how to make one that doesn't burn up, huh? I could get a replacement mail-order chip thingy from Digi-Key, I guess. Dunno what their minimum order is though. BTW, the resistor I marked as 11 ohms reads 51 ohms cold. I said 11 ohms, because that seemed to be its color code -- but the first stripe was a lighter brown than the second, so I was always supicious. Apparently it used to be greeen. :-O However, when I look at eBay or Craig's List, used and even new scanners are a dime a dozen! I paid $133 (incl. tax and less rebate) in San Francisco back in 1998. Craig's List has one of this model (used of course) for $19 and eBay runs from $0.01 minimum bid on this model, to $40 buy-it-now for a new, boxed-up Visioneer One Touch 5800 USB scanner. Is the latter any good? Ray ( http://www.scaner.by.ru/data.htm if your Russian is fluent. ) So I'm not sure how many of these components are bad. Maybe just the output electrolytic? Possibly something on beyond that. I can't find those caps in my junk box, so I'll hit Radio Shack tomorrow. Remember, if you do find it to be an electrolytic, you can replace it with any voltage larger than the one installed and any capacitance larger than the one installed. It is only a filter, so the capacitance is NOT critical. Needless to say, observe the polarity. There are very few semiconductors that operate at less than 5 volts. Well, I guess any of that vintage. But there certainly are now a lot that run on 3 v or so. There are, but they generally are more expensive than the +5 volt variety. As circuits are designed to operate on lower voltages, they are becoming more popular. This in turn causes them to become cheaper. In fact, the cut over level What is that? It really becomes quite involved to explain, but simply stated, the circuits are designed so that stray noise does NOT trigger them. Since noise is unavoidable in most cases, the threshold is designed so that only a signal over .6 volts will switch on a semiconductor. Therefore, most of the time a signal of less than .6 volts is considered a zero, and one greater than 1.6 is considered a one. The area in between these levels were referred in my day as "No man's land." That is, the result of such a voltage was not certain on a circuit. One could turn on, while another might not. Disclaimer: News groups are famous for some person who has little to contribute to a topic jumping in to contradict what another has said. The topic of logic circuits is long and complex. It also has many exceptions, and that is why I even hesitate to start to explain the cross over level topic. I DO NOT HAVE ALL THE ANSWERS!!! Perhaps this might negate the need for someone to blast me??? is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. Yes. Here is a link for a graphic of the type regulator I believe is in the scanner. http://www.nteinc.com/specs/900to999/pdf/nte960.pdf I was wrong about the 9805 number, it is a 7805. (Had another brain fart.) Notice however that the input voltage is on the left of the device, ground is the center terminal, and the output is the left terminal. Yes, you're right, a 7805 and a 7812. With the board out where I can get a flashlight on the regulators at just the right angle, and using a magnifying glass, I can read these old conventional numbers of positive voltage regulators on them. SNIP |
#18
|
|||
|
|||
Raymond A. Chamberlin wrote:
On Sat, 08 Jan 2005 13:45:07 GMT, Ken wrote: Raymond A. Chamberlin wrote: To Ken and CSM1: See interleaved below: On Fri, 07 Jan 2005 20:29:51 GMT, Ken wrote: The 12-v regulator is OK -- +15 v in, +12 v out. The 5-v regulator reads thus: +15 v --11-ohm/2(?)-w res--o--REG--o---- +0.5 v | | 47 µ / 25v 100 µ / 10 v | | gnd gnd The above circuit may be rather scrambled when you get it. Hope not. Ray, I am not sure I am reading your drawing correctly, but if you mean you have .5 volts on the output, THAT IS A PROBLEM. Yes, that's what I mean. And yes, that obviously is a problem. Ray, You have found the problem, now you need to find the solution. The aluminum electrolytics, the regular and the resistor are all quite hot, as is a nearby AIC 1563CN high-efficiency DC/DC converter. It will be very difficult to replace any of the logic circuits attached to this +5 volt bus, but it is possible that a cap is leaking drawing down your +5 volts. More likely, the regulator failed, but the only way to tell is to lift some leads. I would first lift the output from the regulator and measure it. If it is +5, then the problem is on the bus. Using an Ohm meter and lifting leads from caps would be the next easiest, then attack the other components if you choose. For what it is worth, I repaired one of these scanners by replacing the +5 regulator. Of course your results may vary!!! Well, I overlooked a pair of tiny chip/surface-mount components on the other side of the board, one on each side of the regulator to ground. Without looking at the circuit myself, and assuming what you say is true, I would assume they are caps. I would conclude they're either diodes or electrolytics. Do they suppress high-frequency oscillations? They came after my time-in-grade. They are not likely electrolytics due to their being SMDs. Anyhow, I yanked the two radial-lead caps and the regulator. By "yanking", I assume you mean the leads connected to the output have been removed from the +5 volt bus and the short is still there? Or is the short gone from the bus?? All of those appear fine -- as far as I can tell with a 20,000-ohm/v ohmmeter. The chip jobby on the regulator input reads 3.3 ohm one way and 20 ohms the other way (on the 20-ohms-at-center scale. The one on the regulator output reads a dead short both ways on the same scale. I am not quite sure what you mean by the "Chip jobby." If the regulator has been removed, and the output lead on it is shorted to any of the other two leads on the regulator, THAT is your problem. You have a bad regulator. If on the other hand the regulator has been removed and the short still exists on the +5v bus, there is a short on the bus. Suspect caps first, such as those whose leads you have lifted. If the electrolytics have been lifted and the short still exists, look for SMD caps or any semiconductor attached to the bus. I assume the latter ist kaputt. Now, how the devil would I be able to find out the specs of that component -- unless -- ha, ha -- Mostek will tell me? If we are talking about the +5 volt regulator, you can just buy one at Radio Shack for a few pennies. Most of them are rated at something like 1 amp, and it is doubtful that anywhere near that current is being drawn on that circuit. Take your old component with you and just buy a +5 regulator with the same physical characteristics, if that is the component you are talking about. Hey maybe they would send me a whole schematic. . .so I You have got to cut back on the weed smoking or heavy drinking. They are not likely to even ANSWER your request, let alone send you any information!!! could tell them how to make one that doesn't burn up, huh? I could get a replacement mail-order chip thingy from Digi-Key, I guess. Dunno what their minimum order is though. Radio Shack. If you can't find one there, I will mail you one. That is, IF THE REGULATOR is what we are talking about???? BTW, the resistor I marked as 11 ohms reads 51 ohms cold. I said 11 ohms, because that seemed to be its color code -- but the first stripe was a lighter brown than the second, so I was always supicious. Apparently it used to be greeen. :-O If this device is in series with the input voltage of 12 volts, it might well be a coil (choke). Then the marking would not be ohms at all, but milihenries. If you measured +12 with your DVM, the input is OK. Your problem lies with the output. Secondly, measuring a resistor while it is in a circuit often gives false readings because of other attached components. The only effective way would be to lift one lead and measure it. What is important is how many ohms to ground the output bus reads. On the other hand, if the component shorted is a SMD cap on the output bus, then it can probably be replaced with one from a scrap circuit board. This is not easily done, but I have done it many times. It is true it might be for RFI, but it is probably not super critical. If you can find another with similar makings, you will probably be OK. However, when I look at eBay or Craig's List, used and even new scanners are a dime a dozen! I paid $133 (incl. tax and less rebate) in San Francisco back in 1998. Craig's List has one of this model (used of course) for $19 and eBay runs from $0.01 minimum bid on this model, to $40 buy-it-now for a new, boxed-up Visioneer One Touch 5800 USB scanner. Is the latter any good? Ray I don't know anything about other brands of scanners, but you could be only pennies away from fixing your scanner. It is your call. Ken ( http://www.scaner.by.ru/data.htm if your Russian is fluent. ) So I'm not sure how many of these components are bad. Maybe just the output electrolytic? Possibly something on beyond that. I can't find those caps in my junk box, so I'll hit Radio Shack tomorrow. Remember, if you do find it to be an electrolytic, you can replace it with any voltage larger than the one installed and any capacitance larger than the one installed. It is only a filter, so the capacitance is NOT critical. Needless to say, observe the polarity. There are very few semiconductors that operate at less than 5 volts. Well, I guess any of that vintage. But there certainly are now a lot that run on 3 v or so. There are, but they generally are more expensive than the +5 volt variety. As circuits are designed to operate on lower voltages, they are becoming more popular. This in turn causes them to become cheaper. In fact, the cut over level What is that? It really becomes quite involved to explain, but simply stated, the circuits are designed so that stray noise does NOT trigger them. Since noise is unavoidable in most cases, the threshold is designed so that only a signal over .6 volts will switch on a semiconductor. Therefore, most of the time a signal of less than .6 volts is considered a zero, and one greater than 1.6 is considered a one. The area in between these levels were referred in my day as "No man's land." That is, the result of such a voltage was not certain on a circuit. One could turn on, while another might not. Disclaimer: News groups are famous for some person who has little to contribute to a topic jumping in to contradict what another has said. The topic of logic circuits is long and complex. It also has many exceptions, and that is why I even hesitate to start to explain the cross over level topic. I DO NOT HAVE ALL THE ANSWERS!!! Perhaps this might negate the need for someone to blast me??? is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. Yes. Here is a link for a graphic of the type regulator I believe is in the scanner. http://www.nteinc.com/specs/900to999/pdf/nte960.pdf I was wrong about the 9805 number, it is a 7805. (Had another brain fart.) Notice however that the input voltage is on the left of the device, ground is the center terminal, and the output is the left terminal. Yes, you're right, a 7805 and a 7812. With the board out where I can get a flashlight on the regulators at just the right angle, and using a magnifying glass, I can read these old conventional numbers of positive voltage regulators on them. SNIP |
#19
|
|||
|
|||
On Sun, 09 Jan 2005 14:35:00 GMT, Ken wrote:
Raymond A. Chamberlin wrote: On Sat, 08 Jan 2005 13:45:07 GMT, Ken wrote: Raymond A. Chamberlin wrote: To Ken and CSM1: See interleaved below: On Fri, 07 Jan 2005 20:29:51 GMT, Ken wrote: The 12-v regulator is OK -- +15 v in, +12 v out. The 5-v regulator reads thus: +15 v --11-ohm/2(?)-w res--o--REG--o---- +0.5 v | | 47 µ / 25v 100 µ / 10 v | | gnd gnd The above circuit may be rather scrambled when you get it. Hope not. Ray, I am not sure I am reading your drawing correctly, but if you mean you have .5 volts on the output, THAT IS A PROBLEM. Yes, that's what I mean. And yes, that obviously is a problem. Ray, You have found the problem, now you need to find the solution. No, I've just found a symptom. The aluminum electrolytics, the regular and the resistor are all quite hot, as is a nearby AIC 1563CN high-efficiency DC/DC converter. It will be very difficult to replace any of the logic circuits attached to this +5 volt bus, but it is possible that a cap is leaking drawing down your +5 volts. More likely, the regulator failed, but the only way to tell is to lift some leads. I would first lift the output from the regulator and measure it. If it is +5, then the problem is on the bus. Using an Ohm meter and lifting leads from caps would be the next easiest, then attack the other components if you choose. For what it is worth, I repaired one of these scanners by replacing the +5 regulator. Of course your results may vary!!! Well, I overlooked a pair of tiny chip/surface-mount components on the other side of the board, one on each side of the regulator to ground. Without looking at the circuit myself, and assuming what you say is true, I would assume they are caps. I would conclude they're either diodes or electrolytics. Do they suppress high-frequency oscillations? They came after my time-in-grade. They are not likely electrolytics due to their being SMDs. Well, I see such being advertised in the Digi-Key catalog. Anyhow, I yanked the two radial-lead caps and the regulator. By "yanking", I assume you mean the leads connected to the output have been removed from the +5 volt bus I mean these parts are sitting on the bench apart from their board. and the short is still there? Yup; from the trace to what was the regulator output, to what was the regulator ground. Or is the short gone from the bus?? No. All of those appear fine -- as far as I can tell with a 20,000-ohm/v ohmmeter. The chip jobby on the regulator input reads 3.3 ohm one way and 20 ohms the other way (on the 20-ohms-at-center scale. The one on the regulator output reads a dead short both ways on the same scale. I am not quite sure what you mean by the "Chip jobby." The SMD. However, I was fed up with this nonsense at that point and forgot there was still all the other stuff on that regulator-output bus. So it's likely my conclusion that this SMD is shorted is wrong. If the regulator has been removed, and the output lead on it is shorted to any of the other two leads on the regulator, THAT is your problem. You have a bad regulator. No, NO interlead measurement on the regulator, while out of its circuit, shows a short. I have to assume it's just fine; but since the trace that went to its output now still reads shorted to what was its ground trace, if I want to pursue this silly game further, I should check what's left connected to that regulator's output trace, which still shows a short to what was its ground trace. If I got whatever is shorted beyond that point fixed, perhaps I should check the regulator unloaded or externally reasonably loaded to see that its really OK, before puttin it back into its circuit on the board. If on the other hand the regulator has been removed and the short still exists on the +5v bus, there is a short on the bus. Yes, that's the case. Suspect caps first, such as those whose leads you have lifted. If the electrolytics have been lifted and the short still exists, look for SMD caps or any semiconductor attached to the bus. Right. . .if I want to further waste my time (which, I agree, is not worth much at present. But it makes a lot more sense to buy a new scanner. I assume the latter ist kaputt. Now, how the devil would I be able to find out the specs of that component -- unless -- ha, ha -- Mostek will tell me? If we are talking about the +5 volt regulator, you can just buy one at Radio Shack for a few pennies. Most of them are rated at something like 1 amp, and it is doubtful that anywhere near that current is being drawn on that circuit. Take your old component with you and just buy a +5 regulator with the same physical characteristics, if that is the component you are talking about. Well, no, it's not! See above. Actually, though, I did first buy adequate replacements for the regulator input and output radial-lead caps and the regulator itself, the 7805. Radio Shack finally directed me to one of their stores in this town that I didn't know of which actually did have this regulator. I first went to two of their stores and a local independent electronic parts store, all of which were out of 7805s. Hey maybe they would send me a whole schematic. . .so I You have got to cut back on the weed smoking or heavy drinking. They are not likely to even ANSWER your request, let alone send you any information!!! could tell them how to make one that doesn't burn up, huh? I could get a replacement mail-order chip thingy from Digi-Key, I guess. Dunno what their minimum order is though. Radio Shack. If you can't find one there, I will mail you one. That is, IF THE REGULATOR is what we are talking about???? No, that's not what I'M talking about. BTW, the resistor I marked as 11 ohms reads 51 ohms cold. I said 11 ohms, because that seemed to be its color code -- but the first stripe was a lighter brown than the second, so I was always supicious. Apparently it used to be greeen. :-O If this device is in series with the input voltage of 12 volts, No, 12 v. it might well be a coil (choke). Then the marking would not be ohms at all, but milihenries. No, a millihenry choke would never drop the 4.5 v I measured across it when the overloaded 5-volt regulator was in the circuit. I has to be a resistor -- either linear or nonlinear with current. If you measured +12 with your DVM, the input is OK. NO! The input to the +5-v regulator is the +15 v from the plub supply. Your problem lies with the output. Well, something that's HANGING ON the output. I KNOW that. Secondly, measuring a resistor while it is in a circuit often gives false readings because of other attached components. Certainly, but I measured it AFTER I took the regulator and its input electrolytic OUT of the circuit. Thus one end of this resistor was handing free when I measured it at 51 ohms. Of course, it could be half burnt up and thus not the value it was born with. The only effective way would be to lift one lead and measure it. Right on. Thus I did. What is important is how many ohms to ground the output bus reads. Zilch (+\- what I can't see) on the X1-ohm scale of my mirrored 20,000 ohms/v meter. On the other hand, if the component shorted is a SMD cap on the output bus, then it can probably be replaced with one from a scrap circuit board. Yes, I have a scrapped motherboard I bought for another part, which board has at least 50 of the little things on it. Of course, I don't know what size they are, but I agree the size is probably not at all critical. I find it hard to believe this one's necessary at all. There're probably others somewhere down the line on this same bus, where they might make a difference. This is not easily done, but I have done it many times. It is true it might be for RFI, but it is probably not super critical. If you can find another with similar makings, you will probably be OK. However, when I look at eBay or Craig's List, used and even new scanners are a dime a dozen! I paid $133 (incl. tax and less rebate) in San Francisco back in 1998. Craig's List has one of this model (used of course) for $19 and eBay runs from $0.01 minimum bid on this model, to $40 buy-it-now for a new, boxed-up Visioneer One Touch 5800 USB scanner. Is the latter any good? Ray I don't know anything about other brands of scanners, but you could be only pennies away from fixing your scanner. It is your call. Yeah. I could spend hours, maybe days yet, checking out all the parts hanging on this +5-v bus. Just figuring out where it goes is no easy thing. The board appears to be a 4-plane one that is not very translucent. I should run my multimeter over the more than 1000 lead terminations on this board to see how many are on this bus? Even my life of upgrading my software and taking out the trash is more satisfying. It was certainly interesting to find someone who was so completely wave-soldered into the exact scanner I was having trouble with, but this trouble-shooting has gotten way past the limit of reason at this point, I'm afraid. Thanks for all your trouble though. Ray Ken ( http://www.scaner.by.ru/data.htm if your Russian is fluent. ) So I'm not sure how many of these components are bad. Maybe just the output electrolytic? Possibly something on beyond that. I can't find those caps in my junk box, so I'll hit Radio Shack tomorrow. Remember, if you do find it to be an electrolytic, you can replace it with any voltage larger than the one installed and any capacitance larger than the one installed. It is only a filter, so the capacitance is NOT critical. Needless to say, observe the polarity. There are very few semiconductors that operate at less than 5 volts. Well, I guess any of that vintage. But there certainly are now a lot that run on 3 v or so. There are, but they generally are more expensive than the +5 volt variety. As circuits are designed to operate on lower voltages, they are becoming more popular. This in turn causes them to become cheaper. In fact, the cut over level What is that? It really becomes quite involved to explain, but simply stated, the circuits are designed so that stray noise does NOT trigger them. Since noise is unavoidable in most cases, the threshold is designed so that only a signal over .6 volts will switch on a semiconductor. Therefore, most of the time a signal of less than .6 volts is considered a zero, and one greater than 1.6 is considered a one. The area in between these levels were referred in my day as "No man's land." That is, the result of such a voltage was not certain on a circuit. One could turn on, while another might not. Disclaimer: News groups are famous for some person who has little to contribute to a topic jumping in to contradict what another has said. The topic of logic circuits is long and complex. It also has many exceptions, and that is why I even hesitate to start to explain the cross over level topic. I DO NOT HAVE ALL THE ANSWERS!!! Perhaps this might negate the need for someone to blast me??? is generally recognized as 1.6 volts. That is a zero is close to ground and certainly never over .6 volts. A one is never less than 1.6 volts and normally close to the supply voltage. (This is a GENERAL statement and depends upon many factors including the type of semiconductor material.) If you are truly hanging on circuit ground with your meter's common lead and measuring less than either +12 or +5 on the output of these regulators, you have a problem. Certainly the center lead on the regulator is ground, and should read 0 volts. Yes. Here is a link for a graphic of the type regulator I believe is in the scanner. http://www.nteinc.com/specs/900to999/pdf/nte960.pdf I was wrong about the 9805 number, it is a 7805. (Had another brain fart.) Notice however that the input voltage is on the left of the device, ground is the center terminal, and the output is the left terminal. Yes, you're right, a 7805 and a 7812. With the board out where I can get a flashlight on the regulators at just the right angle, and using a magnifying glass, I can read these old conventional numbers of positive voltage regulators on them. SNIP |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
mustek 1200 III EP | M Russon | Scanners | 2 | January 3rd 05 06:37 AM |
wifi | max | Asus Motherboards | 1 | February 25th 04 09:36 PM |
Mustek 1200 CP Problem | Stronak | Scanners | 1 | December 27th 03 02:45 PM |
Receive faxes on Mustek 1200 UB PLUS? | John Whitlow | Scanners | 2 | November 6th 03 07:42 PM |
Driver for scanner Mustek 1200 CU Plus under Windows Xp | Johnny Rappo | Scanners | 0 | August 5th 03 09:15 PM |