If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
BSOD
Your problem is probably a Device and/or Driver.
I would start by taking a long look at the Creative Sound Card. Such as uninstalling it and the related Software. Also try putting it in another PCI slot. I would pop the Creative down to slot 4. Also Creative cards have problems with XP's virtual IRQ's. So IRQ 21,22,23 should be avoided for Creative sound cards. Good luck. ================= MiniDisc_2k2 wrote: Okay, I've been getting this error about once a month, after I come out of standby (S3, a.k.a. STR). It doesn't say any error message like the other BSOD screens I've seen, such as IRQL_NOT_LESS_OR_EQUAL or something like that. All it does is have those annoying hexidecimal codes. Here's my system stats: Gigabyte GA-8SQ800 Pentium 4 Northwood Speed rated 2.4GHz, running 2.95GHz FSB rated 533MHz, running 656MHZ System Bus rated 133MHz, running 164MHz VCore rated 1.55V, running 1.675V 1x256 Corsair High-Quality Ram Speed rated DDR400 running DDR410 BFG Asylum (GeForce4 MX440-SE) 64MB DDR in PCI 1 Creative SoundBlaster PCI512 in PCI 2 Linksys Instant PCI Wireless Networking Card in PCI3 PCI 4/5 empty AGP 4x/8x empty 1x Maxtor 80GB, 7200RPM, 8MB Cache, ATA/133 on Primary Master (CS) 1x Generic 56x CD-ROM on Secondary Master (CS) 1x Generic 3.5" 1.44MB Floppy Drive on Floppy Connector 1x Yamaha CRW3200UXZ (USB 2.0 CD-RW, 24x/10x/40x) The hexidecimal codes I'm getting a ***STOP: 0x0000007E (0xC0000005, 0x80515F86, 0xF9E6CC0C, 0xF9E6C906) What does this mean? Is there any website that can tell me what these codes mean? How can I fix the problem? It's not extremely annoying, as I save all of my data before going into standby anyways so I does no harm, but I'd like to get it resolved. Also, it only happens about once a month so it's no big deal, but it's still bugging me. Thanks for any help -- MiniDisc_2k2 To reply via e-mail, replace nospam.com with cox dot net. |
#2
|
|||
|
|||
"MiniDisc_2k2" wrote in message ... Okay, I've been getting this error about once a month, after I come out of standby (S3, a.k.a. STR). It doesn't say any error message like the other BSOD screens I've seen, such as IRQL_NOT_LESS_OR_EQUAL or something like that. All it does is have those annoying hexidecimal codes. Here's my [chop] The hexidecimal codes I'm getting a ***STOP: 0x0000007E (0xC0000005, 0x80515F86, 0xF9E6CC0C, 0xF9E6C906) What does this mean? Is there any website that can tell me what these codes mean? Microsoft's support site can. It took me less than 30 seconds to find http://support.microsoft.com/support.../q137/5/39.asp -- simply by searching for STOP 0x0000007E. There's a better solution, but since you didn't specify the OS you use in your long list, I can't point you at it. Anyhow, if you have Windows 2000 or XP, search Microsoft's download site for [OS name] Support Tools. If you have NT, I'm not sure there is one. If you have the original Windows 2000 or XP Pro CD (i.e. not an OEM install or upgrade), the support tools are already on the CD. That said, the most common reason for this error is too hard overclocking. That it happens when you go out of standby could be either if you have fans that spin down -- if so, hook them up so they keep running; or you draw too much power at once from the PSP when coming out of standby, not giving the CPU enough juice in its overclocked state -- if so, check whether you can switch to a better power supply. Anyhow, you might want to lower the overclock a tad anyhow, as you've encountered problems. Regards, -- *Art |
#3
|
|||
|
|||
It is not related to BSODs. Problems with Corsair RAM were related to the
memory timings programmed into SPD, they were too aggressive and caused boards not to boot. It has been fixed with New BIOSes. -Paul -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 80,000 Newsgroups - 16 Different Servers! =----- |
#4
|
|||
|
|||
"sig666" wrote in message ... Your problem is probably a Device and/or Driver. I would start by taking a long look at the Creative Sound Card. Such as uninstalling it and the related Software. Also try putting it in another PCI slot. I would pop the Creative down to slot 4. Also Creative cards have problems with XP's virtual IRQ's. So IRQ 21,22,23 should be avoided for Creative sound cards. Good luck. ================= MiniDisc_2k2 wrote: [snip] Thanks for the advice, but please don't top post. |
#5
|
|||
|
|||
Thanks for the advice, but please don't top post.
You've got no right to be pedantic about usenet etiquette mate, when you're asking for, and being given help! |
Thread Tools | |
Display Modes | |
|
|