If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
CDRW not being detected as pri or sec slave...
But it is being detected as pri or sec master. The problem is that I have
two harddrives (6GB and 4GB) as pri master and sec master respectively. Neither of the hd's are detected if I set the jumpers to pri or sec slave with the cdrw as master. My old cdrw is still detected if I set it as slave, but its cd tray is broken, hence the new purchase, a Samsung 52x24x52x. PC has mainboard PCChips M748MR, 400MHz P2 with 128MB RAM. The pc is fairly old, so I don't plan on buying a new hd. Does anyone have any suggestions of a configuration that will have the cdrw set as slave? Is it possible that the Samsung cdrw cannot run as a slave? To clarify: if I set jumpers so that CDRW = pri master and HD1 = pri slave, then HD1 is no longer detected. If I set jumpers so that HD2 = sec master and CDRW = sec slave, then CDRW is not detected and I get an "ATAPI INCOMPATIBLE Press F1 to Resume" error msg. Similar scenario with HD1 = pri master and CDRW = pri slave. If I set jumpers so that HD1 = pri master and HD2 = pri slave, then HD2 is no longer detected. If I set jumpers so that CDRW = sec master and HD1 = pri master while disconnecting HD2, the CDRW is detected and works fine. Pearlf |
#2
|
|||
|
|||
On Sun, 18 Apr 2004 15:28:51 +0200 As truth resonates honesty
"Fredericks" wrote : But it is being detected as pri or sec master. The problem is that I have two harddrives (6GB and 4GB) as pri master and sec master respectively. Neither of the hd's are detected if I set the jumpers to pri or sec slave with the cdrw as master. My old cdrw is still detected if I set it as slave, but its cd tray is broken, hence the new purchase, a Samsung 52x24x52x. PC has mainboard PCChips M748MR, 400MHz P2 with 128MB RAM. The pc is fairly old, so I don't plan on buying a new hd. Does anyone have any suggestions of a configuration that will have the cdrw set as slave? Is it possible that the Samsung cdrw cannot run as a slave? To clarify: if I set jumpers so that CDRW = pri master and HD1 = pri slave, then HD1 is no longer detected. If I set jumpers so that HD2 = sec master and CDRW = sec slave, then CDRW is not detected and I get an "ATAPI INCOMPATIBLE Press F1 to Resume" error msg. Similar scenario with HD1 = pri master and CDRW = pri slave. If I set jumpers so that HD1 = pri master and HD2 = pri slave, then HD2 is no longer detected. If I set jumpers so that CDRW = sec master and HD1 = pri master while disconnecting HD2, the CDRW is detected and works fine. Pearlf Why do you want Cdrom drives as a Master especially if the hard drive is the main system drive? -- Free Windows/PC help, http://www.geocities.com/sheppola/trouble.html email shepATpartyheld.de Free songs to download and,"BURN" :O) http://www.soundclick.com/bands/8/nomessiahsmusic.htm |
#3
|
|||
|
|||
It is unclear if you have tried this set up but surely you one both
harddrives on the primary ide, as master and slave and then you cdrw as secondary master. I don't see why you want your cdrw as slave? Maybe put the okd crdw as master if you want. I have 2 hd's on my primary which never have probs although I sometimes have probs with my 2 cdroms on the secondary when one will sometimes not work (often the master, with the slave working OK). Sometimes ejecting the cd in the working cdrom causes the 'failed' cdrom to spring into life. "Fredericks" wrote in message ... But it is being detected as pri or sec master. The problem is that I have two harddrives (6GB and 4GB) as pri master and sec master respectively. Neither of the hd's are detected if I set the jumpers to pri or sec slave with the cdrw as master. My old cdrw is still detected if I set it as slave, but its cd tray is broken, hence the new purchase, a Samsung 52x24x52x. PC has mainboard PCChips M748MR, 400MHz P2 with 128MB RAM. The pc is fairly old, so I don't plan on buying a new hd. Does anyone have any suggestions of a configuration that will have the cdrw set as slave? Is it possible that the Samsung cdrw cannot run as a slave? To clarify: if I set jumpers so that CDRW = pri master and HD1 = pri slave, then HD1 is no longer detected. If I set jumpers so that HD2 = sec master and CDRW = sec slave, then CDRW is not detected and I get an "ATAPI INCOMPATIBLE Press F1 to Resume" error msg. Similar scenario with HD1 = pri master and CDRW = pri slave. If I set jumpers so that HD1 = pri master and HD2 = pri slave, then HD2 is no longer detected. If I set jumpers so that CDRW = sec master and HD1 = pri master while disconnecting HD2, the CDRW is detected and works fine. Pearlf |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DSL modem can no longer be detected correctly by router | Mattrixx | General | 0 | February 18th 04 05:10 PM |
lost primary slave when installing ASUS A7V8X-X | BC Berry | General | 3 | January 1st 04 02:33 AM |
DVD / CDRW drive master slave situation | - | General | 3 | November 24th 03 10:23 PM |
LG CDRW & Nero 5.5.9.9? | Gareth Church | General | 2 | July 10th 03 04:55 AM |
set CDROM as master not slave? | kony | General | 1 | June 28th 03 07:40 AM |