If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Lun WWN on HDS arrays
I have a HDS 9200 and HDS 9960 arrays.I have created few luns on both
of them and have added the host access for the luns on both the arrays.On the host side I need to find out the lun wwn for the luns I have created on both the systems.The management interface of both the arrays does not display the LUN WWN which I just created. Is there a way to find out the LUN WWN from the host side.Is there a tool available for finding the LUN WWN. Any suggestions/tricks will be appreciated. |
#2
|
|||
|
|||
The tool depends on the HBA on the host. If it is Qlogic use Sansurfer, if
emulex use HBAanywhere etc.. The tools are available for download from HBA vendor. "Milind Koli" wrote in message . com... I have a HDS 9200 and HDS 9960 arrays.I have created few luns on both of them and have added the host access for the luns on both the arrays.On the host side I need to find out the lun wwn for the luns I have created on both the systems.The management interface of both the arrays does not display the LUN WWN which I just created. Is there a way to find out the LUN WWN from the host side.Is there a tool available for finding the LUN WWN. Any suggestions/tricks will be appreciated. |
#3
|
|||
|
|||
I am using emulex HBA , from HBAanywhere I can see the port wwn on both
the arrays and the port wwn of the host.I can see the luns which I have created but they show up as LUN 0 ,LUN 1, LUN 2 and so on.If I select a particular LUN the right hand side of the hbanywhere shows the lun attributes as follows LUN Details :1 Hiearchical Lun : 0000 0001 0000 0000 "scsisam" wrote in message news:juUzb.304631$9E1.1542199@attbi_s52... The tool depends on the HBA on the host. If it is Qlogic use Sansurfer, if emulex use HBAanywhere etc.. The tools are available for download from HBA vendor. "Milind Koli" wrote in message . com... I have a HDS 9200 and HDS 9960 arrays.I have created few luns on both of them and have added the host access for the luns on both the arrays.On the host side I need to find out the lun wwn for the luns I have created on both the systems.The management interface of both the arrays does not display the LUN WWN which I just created. Is there a way to find out the LUN WWN from the host side.Is there a tool available for finding the LUN WWN. Any suggestions/tricks will be appreciated. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
mixing hard drives on a 4250es controller, and bigger arrays | randoms | Compaq Servers | 0 | January 31st 05 06:41 PM |
Parting out some Proliants and Disk Arrays | dsh | Compaq Servers | 0 | November 22nd 04 08:01 PM |
Inexpensive External Disk Arrays? | G.L. Cross | General | 1 | August 19th 04 05:27 PM |
How fast are your RAID arrays??? | TJM | Homebuilt PC's | 4 | May 13th 04 10:27 PM |
Electrical Feedback and arrays | Rich | Storage & Hardrives | 0 | September 18th 03 08:15 PM |