If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
My video capture PAL settings keep resetting to NTSC every bootup using a MSI GeforceFX5900XT VTD128
hi all,
I've been racking my brain over this problem for months now and I've searched and searched and still cannot fix this little problem I have.... the problem is this.... My WDM video capture PAL settings keep resetting themselves to NTSC on every bootup and the only way I can reset it back to PAL is by messing about each time and loading up the AMCAP.exe program first to set the format to PAL before using VirtualDub cause if I don't do that first then I get the bottom part of the captured video cut off and it looks plain wrong. I'm using a MSI GeforceFX5900XT VTD128 card with VIVO drivers v1.0.8.0 (it says this in the device manager for my "nVidia WDM Video Capture Universal" section) The same thing happens with any WDM capture drivers I installed in the past but I am assuming it's the nVidia card setting itself to a default of NTSC each time but I need it to stay permanently set on PAL (which it doesn't seem to want to do?) Any help to enlighten me as to how to easily set this to PAL permanently would be much appreciated thanks! |
#2
|
|||
|
|||
On Mon, 9 Aug 2004 18:38:58 +0100 "NeonBlue" meeped
: hi all, I've been racking my brain over this problem for months now and I've searched and searched and still cannot fix this little problem I have.... the problem is this.... My WDM video capture PAL settings keep resetting themselves to NTSC on every bootup and the only way I can reset it back to PAL is by messing about each time and loading up the AMCAP.exe program first to set the format to PAL before using VirtualDub cause if I don't do that first then I get the bottom part of the captured video cut off and it looks plain wrong. I'm using a MSI GeforceFX5900XT VTD128 card with VIVO drivers v1.0.8.0 (it says this in the device manager for my "nVidia WDM Video Capture Universal" section) The same thing happens with any WDM capture drivers I installed in the past but I am assuming it's the nVidia card setting itself to a default of NTSC each time but I need it to stay permanently set on PAL (which it doesn't seem to want to do?) Any help to enlighten me as to how to easily set this to PAL permanently would be much appreciated thanks! The 108's should be ok..they're the only ones Ive ever used that dont reset to NTSC on reboot....although..thinking about it I might have edited the INF file.. open up the file NVCAP.INF see what this bit says.... I think i changed it from AUTO...to PAL..and it works ############################################### HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" ################################################ -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( |
#3
|
|||
|
|||
"Granulated" wrote in message
... On Mon, 9 Aug 2004 18:38:58 +0100 "NeonBlue" meeped : hi all, I've been racking my brain over this problem for months now and I've searched and searched and still cannot fix this little problem I have.... the problem is this.... My WDM video capture PAL settings keep resetting themselves to NTSC on every bootup and the only way I can reset it back to PAL is by messing about each time and loading up the AMCAP.exe program first to set the format to PAL before using VirtualDub cause if I don't do that first then I get the bottom part of the captured video cut off and it looks plain wrong. I'm using a MSI GeforceFX5900XT VTD128 card with VIVO drivers v1.0.8.0 (it says this in the device manager for my "nVidia WDM Video Capture Universal" section) The same thing happens with any WDM capture drivers I installed in the past but I am assuming it's the nVidia card setting itself to a default of NTSC each time but I need it to stay permanently set on PAL (which it doesn't seem to want to do?) Any help to enlighten me as to how to easily set this to PAL permanently would be much appreciated thanks! The 108's should be ok..they're the only ones Ive ever used that dont reset to NTSC on reboot....although..thinking about it I might have edited the INF file.. open up the file NVCAP.INF see what this bit says.... I think i changed it from AUTO...to PAL..and it works ############################################### HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" ################################################ -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( thanks! I hadn't thought about that one! so I shall try that out right now I'll post back to say how I got on.... |
#4
|
|||
|
|||
"Granulated" wrote in message
... On Mon, 9 Aug 2004 18:38:58 +0100 "NeonBlue" meeped : hi all, I've been racking my brain over this problem for months now and I've searched and searched and still cannot fix this little problem I have.... the problem is this.... My WDM video capture PAL settings keep resetting themselves to NTSC on every bootup and the only way I can reset it back to PAL is by messing about each time and loading up the AMCAP.exe program first to set the format to PAL before using VirtualDub cause if I don't do that first then I get the bottom part of the captured video cut off and it looks plain wrong. I'm using a MSI GeforceFX5900XT VTD128 card with VIVO drivers v1.0.8.0 (it says this in the device manager for my "nVidia WDM Video Capture Universal" section) The same thing happens with any WDM capture drivers I installed in the past but I am assuming it's the nVidia card setting itself to a default of NTSC each time but I need it to stay permanently set on PAL (which it doesn't seem to want to do?) Any help to enlighten me as to how to easily set this to PAL permanently would be much appreciated thanks! The 108's should be ok..they're the only ones Ive ever used that dont reset to NTSC on reboot....although..thinking about it I might have edited the INF file.. open up the file NVCAP.INF see what this bit says.... I think i changed it from AUTO...to PAL..and it works ############################################### HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" ################################################ thanks for the help, I'm sure this must be the way to fix it as you said but I'm still in the dark a bit as to which part to change and where? do I change it in the windows/system folder or do I change it in the main place where I extracted the drivers and then reinstall them? I attempted to change it to the following but it still seems to get stuck on NTSC anyway each bootup also there's some very dodgy looking large numbers in the slider bars (in Virtualdub video source settings) for the saturation, hue, brightness, etc so I think I messed it up with my tweaking somehow so I will uninstall the drivers as best I can and reinstall them. ################################################## ########## ;--------------------------------------------------------------- ; Decoder related values ; All values in the decoder key and subkeys are string values ;--------------------------------------------------------------- [nvcap.AddReg] HKR,,DevLoader,,*NTKERN HKR,,NTMPDriver,,nvcap.sys HKR,,PhilComp,,VIN0 ; input sel for ext. tuner (philips) design ;HKR,,PhilTuner,,VIN0 HKR,,PhilSVideo,,VIN6 HKR,,AIOComp,,VIN3 ; input sel for all-in-1 ;HKR,,AIOTuner,,VIN1 HKR,,AIOSVideo,,VIN6 HKR,,VPXComp,,VIN2 ; input sel for ext. tuner (micronas) design ;HKR,,VPXTuner,,VIN1 HKR,,VPXSVideo,,VIN3 HKR,,DefaultIn,,Comp HKR,,ExtSwitch,,TRUE HKR,,Manufacturer,,ASUS HKR,,Address,,0x4a ; I2C address only important if ; VideoDecoder != AUTO HKR,,InterfaceType,,D1 ; "D1" (8 bit) or "DMSD16" (16 bit) HKR,,VideoDecoder,,AUTO ; "SAA7111", "SAA7111A", "SAA7112V0", ; "SAA7112", "SAA7113V0", "SAA7113", ; "SAA7113A", "SAA7114", "AUTO" HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" HKR,,OutputFormat,,CCIR656 ; "YUV422", "YUV411", "YUV420", ; "YUV410", "YUV9", "RGB565", ; "RGB888", "CCIR656" HKR,,VBIMode,,RAW ; "RAW", "BASEBAND" (optinal) HKR,,VBILineWidth,,720 ; only needed if VBIMode used HKR,,VBILineOffset,,0 ; only needed if VBIMode used HKR,,EnableSlicer,,0 ; Enable slicer if it is present HKR,,Oversample,,4 ; 4..Use Philips 27MHz Frequency ; 5..Use 5x for old Microsoft CC- & NABTS Codecs ################################################## ############ as you can see I rem'ed out a few TVTuner lines with semi-colons (as I don't have a tuner on this card and it said to do that so it doesn't enumerate the tuner on startup but it did anyway :-\ ) and I also changed the: HKR,,VideoStandard,,NTSC ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" to this: HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" as an added bonus it seems to also returns this error in Virtualdub......Status 411: Warning no frames were captured, try turning overlay off, reduce capture resolution or reducing colour depth to 16 or 24 bit....... but I am sure that this is related to the drivers as I have captured video perfectly ok with this card before no probs and the only thing I did recently was a reinstall of windows. I'll keep trying to sort it out anyway and I'll post back if I manage to fix it any and thanks again for your help |
#5
|
|||
|
|||
On Fri, 13 Aug 2004 01:19:39 +0100 "NeonBlue"
meeped : "Granulated" wrote in message .. . On Mon, 9 Aug 2004 18:38:58 +0100 "NeonBlue" meeped : hi all, I've been racking my brain over this problem for months now and I've searched and searched and still cannot fix this little problem I have.... the problem is this.... My WDM video capture PAL settings keep resetting themselves to NTSC on every bootup and the only way I can reset it back to PAL is by messing about each time and loading up the AMCAP.exe program first to set the format to PAL before using VirtualDub cause if I don't do that first then I get the bottom part of the captured video cut off and it looks plain wrong. I'm using a MSI GeforceFX5900XT VTD128 card with VIVO drivers v1.0.8.0 (it says this in the device manager for my "nVidia WDM Video Capture Universal" section) The same thing happens with any WDM capture drivers I installed in the past but I am assuming it's the nVidia card setting itself to a default of NTSC each time but I need it to stay permanently set on PAL (which it doesn't seem to want to do?) Any help to enlighten me as to how to easily set this to PAL permanently would be much appreciated thanks! The 108's should be ok..they're the only ones Ive ever used that dont reset to NTSC on reboot....although..thinking about it I might have edited the INF file.. open up the file NVCAP.INF see what this bit says.... I think i changed it from AUTO...to PAL..and it works ############################################### HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" ################################################ thanks for the help, I'm sure this must be the way to fix it as you said but I'm still in the dark a bit as to which part to change and where? do I change it in the windows/system folder or do I change it in the main place where I extracted the drivers and then reinstall them? I attempted to change it to the following but it still seems to get stuck on NTSC anyway each bootup also there's some very dodgy looking large numbers in the slider bars (in Virtualdub video source settings) for the saturation, hue, brightness, etc so I think I messed it up with my tweaking somehow so I will uninstall the drivers as best I can and reinstall them. ################################################# ########### ;--------------------------------------------------------------- ; Decoder related values ; All values in the decoder key and subkeys are string values ;--------------------------------------------------------------- [nvcap.AddReg] HKR,,DevLoader,,*NTKERN HKR,,NTMPDriver,,nvcap.sys HKR,,PhilComp,,VIN0 ; input sel for ext. tuner (philips) design ;HKR,,PhilTuner,,VIN0 HKR,,PhilSVideo,,VIN6 HKR,,AIOComp,,VIN3 ; input sel for all-in-1 ;HKR,,AIOTuner,,VIN1 HKR,,AIOSVideo,,VIN6 HKR,,VPXComp,,VIN2 ; input sel for ext. tuner (micronas) design ;HKR,,VPXTuner,,VIN1 HKR,,VPXSVideo,,VIN3 HKR,,DefaultIn,,Comp HKR,,ExtSwitch,,TRUE HKR,,Manufacturer,,ASUS HKR,,Address,,0x4a ; I2C address only important if ; VideoDecoder != AUTO HKR,,InterfaceType,,D1 ; "D1" (8 bit) or "DMSD16" (16 bit) HKR,,VideoDecoder,,AUTO ; "SAA7111", "SAA7111A", "SAA7112V0", ; "SAA7112", "SAA7113V0", "SAA7113", ; "SAA7113A", "SAA7114", "AUTO" HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" HKR,,OutputFormat,,CCIR656 ; "YUV422", "YUV411", "YUV420", ; "YUV410", "YUV9", "RGB565", ; "RGB888", "CCIR656" HKR,,VBIMode,,RAW ; "RAW", "BASEBAND" (optinal) HKR,,VBILineWidth,,720 ; only needed if VBIMode used HKR,,VBILineOffset,,0 ; only needed if VBIMode used HKR,,EnableSlicer,,0 ; Enable slicer if it is present HKR,,Oversample,,4 ; 4..Use Philips 27MHz Frequency ; 5..Use 5x for old Microsoft CC- & NABTS Codecs ################################################# ############# as you can see I rem'ed out a few TVTuner lines with semi-colons (as I don't have a tuner on this card and it said to do that so it doesn't enumerate the tuner on startup but it did anyway :-\ ) and I also changed the: HKR,,VideoStandard,,NTSC ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" to this: HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" as an added bonus it seems to also returns this error in Virtualdub......Status 411: Warning no frames were captured, try turning overlay off, reduce capture resolution or reducing colour depth to 16 or 24 bit....... but I am sure that this is related to the drivers as I have captured video perfectly ok with this card before no probs and the only thing I did recently was a reinstall of windows. I'll keep trying to sort it out anyway and I'll post back if I manage to fix it any and thanks again for your help ok between the hashes is a complete COPY of my INF file..... HTH ################################################## ################ ; nvcap.INF -- This file installs nvcap.sys ; ; Created 11.Nov.97 (Creation Date) ; Updated 16.Dec.97 ; Updated 16.Mar.98 ; Updated 17.Jun.98 ; Updated 01.Okt.98 ; Updated Jun21,2000 Cheehoi ; Updated 2-6-2001 Customization for Ext Tuner Box [Version] signature="$CHICAGO$" Class=MEDIA ClassGUID={4d36e96c-e325-11ce-bfc1-08002be10318} Provider=%MS% LayoutFile=LAYOUT.INF, layout1.inf, layout2.inf DriverVer = 11/16/2001, 1.0.8 ;CatalogFile=NVCAP.CAT [DestinationDirs] nvcap.CopyDrivers=10,system32\drivers ; eg. \windows\system32\drivers nvcap.CopyCodec=11 [SourceDisksNames] 1=%Disk1Name%,,,%10% [SourceDisksFiles] nvcap.sys=1,system32\drivers [Manufacturer] %MS%=MS [MS] %nvcap.DeviceDesc%=nvcap.Device,DISPLAY\nvcap ;------------------------------------------------------------------------------- [nvcap.Device] Include = ks.inf, kscaptur.inf, ksfilter.inf Needs= KS.Registration,KSCAPTUR.Registration,MSPCLOCK.Ins tallation AddReg = nvcap.AddReg UpdateInis= nvcap.UpdateIni CopyFiles= nvcap.CopyDrivers, nvcap.CopyCodec DelFiles = nvcap.DelDrivers KnownFiles= nvcap.KnownFiles [nvcap.Device.NT] Include = ks.inf, kscaptur.inf, ksfilter.inf Needs= KS.Registration,KSCAPTUR.Registration.NT,MSPCLOCK. Installation AddReg = nvcap.AddReg UpdateInis= nvcap.UpdateIni CopyFiles= nvcap.CopyDrivers, nvcap.CopyCodec DelFiles = nvcap.DelDrivers [nvcap.CopyDrivers] ;nvcap.sys stream.sys [nvcap.CopyCodec] msyuv.dll [nvcap.UpdateIni] system.ini, drivers32,,"VIDC.UYVY=msyuv.dll" [nvcap.KnownFiles] nvcap.sys=safe [nvcap.DelDrivers] ;--------------------------------------------------------------- ; Decoder related values ; All values in the decoder key and subkeys are string values ;--------------------------------------------------------------- [nvcap.AddReg] HKR,,DevLoader,,*NTKERN HKR,,NTMPDriver,,nvcap.sys ;/////////////nVidia Customizations////////////////////////////// ; ; Please read this !!!!!!!!!!!!!!!!!!!!!!!!!! ; Is video input does not switch correctly or ; audio doesn't mute, most probably the settings here are ; incorrect. ; ; 1)If an input source(PhilComp, PhilTuner etc) is removed, ; it won't be enumerated by the capture driver. ; Ex. If you do not want TUNER support for the All-in-one design ; remove "HKR,,AIOTuner,,VINX" key and Tuner input won't be ; enumerated. ; ;//////////////////////////////////////////////////////////////// ;----Customization for external tuner box----------------------- ; This is the translucent green box ;--------------------------------------------------------------- HKR,,PhilComp,,VIN0 ; input sel for ext. tuner (philips) design HKR,,PhilTuner,,VIN0 HKR,,PhilSVideo,,VIN6 ;----Customization for the ALL-In-One design-------------------- HKR,,AIOComp,,VIN0 ; input sel for all-in-1 HKR,,AIOSVideo,,VIN6 ;----Customization for the Micronas VPX chipsets---------------- HKR,,VPXComp,,VIN2 ; input sel for ext. tuner (micronas) design HKR,,VPXTuner,,VIN1 HKR,,VPXSVideo,,VIN3 HKR,,DefaultIn,,Comp HKR,,ExtSwitch,,FALSE HKR,,Manufacturer,, ;--------------------------------------------------------------- ; Subkey for VidComp ; 8574=W/46/ff ; 8575=W/46/ff/3 ;--------------------------------------------------------------- HKR,VidComp,NumCmd,,1 HKR,VidComp,Cmd0,,W/46/ff ;--------------------------------------------------------------- ; Subkey for VidSVid ; 8574=W/46/bf ; 8575=W/46/ff/2 ;--------------------------------------------------------------- HKR,VidSVid,NumCmd,,1 HKR,VidSVid,Cmd0,,W/46/bf ;--------------------------------------------------------------- ; Subkey for VidTuner ; 8574=W/46/7f ; 8575=W/46/ff/1 ;--------------------------------------------------------------- HKR,VidTuner,NumCmd,,1 HKR,VidTuner,Cmd0,,W/46/7f ;--------------------------------------------------------------- ; Subkey for AudTuner ;--------------------------------------------------------------- HKR,AudTuner,NumCmd,,0 ;--------------------------------------------------------------- ; Subkey for AudLineIn ;--------------------------------------------------------------- HKR,AudLineIn,NumCmd,,0 ;--------------------------------------------------------------- ; Subkey for AudMute ; 9850 = W/b6/6/18 ; 9874 = W/b0/12/ff ; 9873 = W/b4/0/40 ;--------------------------------------------------------------- HKR,AudMute,NumCmd,,0 ;HKR,AudMute,Cmd0,,W/b6/6/18 ;--------------------------------------------------------------- ; Subkey for AudUnMute ; 9850 = W/b6/6/40 ; 9874 = W/b0/12/fb ; 9873 = W/b4/0/90 ;--------------------------------------------------------------- HKR,AudUnMute,NumCmd,,0 ;HKR,AudUnMute,Cmd0,,W/b6/6/40 ;--------------------------------------------------------------- ; Subkey for board customization ;--------------------------------------------------------------- HKR,Custom,NumCmd,,1 HKR,Custom,Cmd0,,W/46/3f ;///////////End of nVidia Customization////////////////////////// ;////////////////Philips HAL customization/////////////////////// HKR,,Address,,0x4a ; I2C address only important if ; VideoDecoder != AUTO HKR,,InterfaceType,,D1 ; "D1" (8 bit) or "DMSD16" (16 bit) HKR,,VideoDecoder,,AUTO ; "SAA7111", "SAA7111A", "SAA7112V0", ; "SAA7112", "SAA7113V0", "SAA7113", ; "SAA7113A", "SAA7114", "AUTO" HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" HKR,,OutputFormat,,CCIR656 ; "YUV422", "YUV411", "YUV420", ; "YUV410", "YUV9", "RGB565", ; "RGB888", "CCIR656" HKR,,VBIMode,,RAW ; "RAW", "BASEBAND" (optinal) HKR,,VBILineWidth,,720 ; only needed if VBIMode used HKR,,VBILineOffset,,0 ; only needed if VBIMode used HKR,,EnableSlicer,,0 ; Enable slicer if it is present HKR,,Oversample,,4 ; 4..Use Philips 27MHz Frequency ; 5..Use 5x for old Microsoft CC- & NABTS Codecs ;--------------------------------------------------------------- ; Subkey for video source 1 ;--------------------------------------------------------------- HKR,VidSrc1,InputMode,,0 HKR,VidSrc1,SourceType,,VCR HKR,VidSrc1,VideoType,,Composite HKR,VidSrc1,ScalerFID,,DEFAULT HKR,VidSrc1,ScalerMode,,DEFAULT ;--------------------------------------------------------------- ; Subkey for video source 2 ;--------------------------------------------------------------- HKR,VidSrc2,InputMode,,0 HKR,VidSrc2,SourceType,,TV HKR,VidSrc2,VideoType,,Tuner HKR,VidSrc2,ScalerFID,,DEFAULT HKR,VidSrc2,ScalerMode,,DEFAULT ;--------------------------------------------------------------- ; Subkey for video source 3 ;--------------------------------------------------------------- HKR,VidSrc3,InputMode,,6 HKR,VidSrc3,SourceType,,VCR HKR,VidSrc3,VideoType,,SVHS HKR,VidSrc3,ScalerFID,,DEFAULT HKR,VidSrc3,ScalerMode,,DEFAULT ;--------------------------------------------------------------- ; Subkey Description for video sources (optional) ;--------------------------------------------------------------- ; Subkeyname : "VidSrcX" - X = number of input ; InputMode : Decoder input mode for video source ("0" to "9") ; SourceType : "Camera", "TV", "VCR" ; VideoType : "Tuner", "Composite", "SVHS", "Extern_1" ; ScalerFID : "DEFAULT", "INVERT" (optional) ; ScalerMode : "DEFAULT", "HIGH_BANDWIDTH", "LOW_BANDWIDTH" (optional) ;--------------------------------------------------------------- ; Subkey Description for teletext sources (optional) ;--------------------------------------------------------------- ; Subkeyname : "TelSrcX" - X = number of input ; InputType : "INTERNAL", ""EXTERNAL_1" ;--------------------------------------------------------------- ; Subkey example for teletext source (optional) ;--------------------------------------------------------------- ; HKR,TelSrc1,InputType,,INTERNAL ;--------------------------------------------------------------- ; Subkey Description for default values (optional) ;--------------------------------------------------------------- ; Subkeyname: "DefaultSaa7111" for defaults of Saa7111 ; "DefaultSaa7111A" for defaults of Saa7111A ; "DefaultSaa7112V0" for defaults of Saa7112V0 ; "DefaultSaa7112" for defaults of Saa7112 ; "DefaultSaa7113V0" for defaults of Saa7113V0 ; "DefaultSaa7113" for defaults of Saa7113 ; "DefaultSaa7113A" for defaults of Saa7113A ; "DefaultSaa7114" for defaults of Saa7114 ; Reg0xXXX : Value of register 0xXXX (hex) overwriting the ; value in the hardcoded default array. The register ; number in the key must be hex with leading 0x and ; must contain 3 digits! ;--------------------------------------------------------------- ; Subkey for default values for the Saa7113 ; The hardcoded default value 0x82 of register 0x40 is replaced ; with 0x02 which is necessary for PAL ;--------------------------------------------------------------- HKR,DefaultSaa7113,Reg0x040,,0x02 HKR,DefaultSaa7113V0,Reg0x040,,0x02 ;--------------------------------------------------------------- ; Subkey for default values for the Saa7114 ; The hardcoded default value 0x00 of register 0x80 is replaced ; with 0x10 which is necessary for NTSC sliced data interface ;--------------------------------------------------------------- ;HKR,DefaultSaa7114,Reg0x080,,0x40 ;only when EnableSlicer=1 !!! ;/////////////////End of Philips HAL customization////////////// [nvcap.Device.Interfaces] AddInterface={65e8773d-8f56-11d0-a3b9-00a0c9223196},"GLOBAL",VideoCapture, AddInterface={a799a801-a46d-11d0-a18c-00a02401dcd4},"GLOBAL",VideoCrossbar, [nvcap.Device.NT.Interfaces] AddInterface={65e8773d-8f56-11d0-a3b9-00a0c9223196},"GLOBAL",VideoCapture, AddInterface={a799a801-a46d-11d0-a18c-00a02401dcd4},"GLOBAL",VideoCrossbar, [VideoCapture] AddReg=VideoCapture.AddReg [VideoCrossbar] AddReg=VideoXBar.AddReg [VideoCapture.AddReg] HKR,,CLSID,,{17CCA71B-ECD7-11D0-B908-00A0C9223196} HKR,,FriendlyName,,%nvcap.Capture% HKR,,PageOutWhenUnopened,1,01 HKR,,DontSuspendIfStreamsAreRunning,1,01 [VideoXBar.AddReg] HKR,,CLSID,,{71F96460-78F3-11d0-A18C-00A0C9118956} HKR,,FriendlyName,,%nvcap.Crossbar% [nvcap.Device.NT.Services] AddService = nvcap,0x00000002,nvcap.ServiceInstall [nvcap.ServiceInstall] DisplayName = %nvcap.DeviceDesc% ServiceType = %SERVICE_KERNEL_DRIVER% StartType = %SERVICE_AUTO_START% ErrorControl = %SERVICE_ERROR_NORMAL% ServiceBinary = %12%\nvcap.sys ;--------------------------------------------------------------- ; S t r i n g s ;--------------------------------------------------------------- [Strings] ;---------------- ; Non-Localizable ;---------------- SERVICE_KERNEL_DRIVER=1 SERVICE_AUTO_START=2 SERVICE_ERROR_NORMAL=1 ;---------------- ; Localizable ;---------------- Msft = "nVidia Corporation" MS = "nVidia" captureClassName = "Sound, video and game controllers" nvcap.DeviceDesc = "nVidia WDM Video Capture (universal)" nvcap.Capture = "nVidia WDM Video Capture (universal)" nvcap.Crossbar = "nVidia WDM Video Crossbar (universal)" Disk1Name = "nVidia WDM Drivers Disk 1" ################################################## ####################################### -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( |
#6
|
|||
|
|||
On Fri, 13 Aug 2004 01:19:39 +0100 "NeonBlue"
meeped : HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" WHy did you put PAL_I ? it's not even in the list ! I -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( |
#7
|
|||
|
|||
I used PAL_I as that is the one which seems to work for me when I select it
in AMCAP's video format (it then displays it as being 625 lines and not NTSC_M as it always seems to default to. I did, as you say, realise it wasn't in the list and have tried it with PAL too now and it still seems not to allow it to be set to PAL and just keeps constantly reverting to NTSC_M mode each bootup. I used regedit to search for the word "VideoStandard" in the registry and I found where it said PAL_I and I have changed it to PAL now so I will reboot again and see if it works this time and repost if it does or not thanks for the help "Granulated" wrote in message ... On Fri, 13 Aug 2004 01:19:39 +0100 "NeonBlue" meeped : HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" WHy did you put PAL_I ? it's not even in the list ! I -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( |
#8
|
|||
|
|||
"Granulated" wrote in message news On Fri, 13 Aug 2004 01:19:39 +0100 "NeonBlue" meeped : "Granulated" wrote in message . .. On Mon, 9 Aug 2004 18:38:58 +0100 "NeonBlue" meeped : hi all, I've been racking my brain over this problem for months now and I've searched and searched and still cannot fix this little problem I have.... the problem is this.... My WDM video capture PAL settings keep resetting themselves to NTSC on every bootup and the only way I can reset it back to PAL is by messing about each time and loading up the AMCAP.exe program first to set the format to PAL before using VirtualDub cause if I don't do that first then I get the bottom part of the captured video cut off and it looks plain wrong. I'm using a MSI GeforceFX5900XT VTD128 card with VIVO drivers v1.0.8.0 (it says this in the device manager for my "nVidia WDM Video Capture Universal" section) The same thing happens with any WDM capture drivers I installed in the past but I am assuming it's the nVidia card setting itself to a default of NTSC each time but I need it to stay permanently set on PAL (which it doesn't seem to want to do?) Any help to enlighten me as to how to easily set this to PAL permanently would be much appreciated thanks! The 108's should be ok..they're the only ones Ive ever used that dont reset to NTSC on reboot....although..thinking about it I might have edited the INF file.. open up the file NVCAP.INF see what this bit says.... I think i changed it from AUTO...to PAL..and it works ############################################### HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" ################################################ thanks for the help, I'm sure this must be the way to fix it as you said but I'm still in the dark a bit as to which part to change and where? do I change it in the windows/system folder or do I change it in the main place where I extracted the drivers and then reinstall them? I attempted to change it to the following but it still seems to get stuck on NTSC anyway each bootup also there's some very dodgy looking large numbers in the slider bars (in Virtualdub video source settings) for the saturation, hue, brightness, etc so I think I messed it up with my tweaking somehow so I will uninstall the drivers as best I can and reinstall them. ################################################ ############ ;--------------------------------------------------------------- ; Decoder related values ; All values in the decoder key and subkeys are string values ;--------------------------------------------------------------- [nvcap.AddReg] HKR,,DevLoader,,*NTKERN HKR,,NTMPDriver,,nvcap.sys HKR,,PhilComp,,VIN0 ; input sel for ext. tuner (philips) design ;HKR,,PhilTuner,,VIN0 HKR,,PhilSVideo,,VIN6 HKR,,AIOComp,,VIN3 ; input sel for all-in-1 ;HKR,,AIOTuner,,VIN1 HKR,,AIOSVideo,,VIN6 HKR,,VPXComp,,VIN2 ; input sel for ext. tuner (micronas) design ;HKR,,VPXTuner,,VIN1 HKR,,VPXSVideo,,VIN3 HKR,,DefaultIn,,Comp HKR,,ExtSwitch,,TRUE HKR,,Manufacturer,,ASUS HKR,,Address,,0x4a ; I2C address only important if ; VideoDecoder != AUTO HKR,,InterfaceType,,D1 ; "D1" (8 bit) or "DMSD16" (16 bit) HKR,,VideoDecoder,,AUTO ; "SAA7111", "SAA7111A", "SAA7112V0", ; "SAA7112", "SAA7113V0", "SAA7113", ; "SAA7113A", "SAA7114", "AUTO" HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" HKR,,OutputFormat,,CCIR656 ; "YUV422", "YUV411", "YUV420", ; "YUV410", "YUV9", "RGB565", ; "RGB888", "CCIR656" HKR,,VBIMode,,RAW ; "RAW", "BASEBAND" (optinal) HKR,,VBILineWidth,,720 ; only needed if VBIMode used HKR,,VBILineOffset,,0 ; only needed if VBIMode used HKR,,EnableSlicer,,0 ; Enable slicer if it is present HKR,,Oversample,,4 ; 4..Use Philips 27MHz Frequency ; 5..Use 5x for old Microsoft CC- & NABTS Codecs ################################################ ############## as you can see I rem'ed out a few TVTuner lines with semi-colons (as I don't have a tuner on this card and it said to do that so it doesn't enumerate the tuner on startup but it did anyway :-\ ) and I also changed the: HKR,,VideoStandard,,NTSC ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" to this: HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" as an added bonus it seems to also returns this error in Virtualdub......Status 411: Warning no frames were captured, try turning overlay off, reduce capture resolution or reducing colour depth to 16 or 24 bit....... but I am sure that this is related to the drivers as I have captured video perfectly ok with this card before no probs and the only thing I did recently was a reinstall of windows. I'll keep trying to sort it out anyway and I'll post back if I manage to fix it any and thanks again for your help ok between the hashes is a complete COPY of my INF file..... HTH ################################################## ################ ; nvcap.INF -- This file installs nvcap.sys ; ; Created 11.Nov.97 (Creation Date) ; Updated 16.Dec.97 ; Updated 16.Mar.98 ; Updated 17.Jun.98 ; Updated 01.Okt.98 ; Updated Jun21,2000 Cheehoi ; Updated 2-6-2001 Customization for Ext Tuner Box [Version] signature="$CHICAGO$" Class=MEDIA ClassGUID={4d36e96c-e325-11ce-bfc1-08002be10318} Provider=%MS% LayoutFile=LAYOUT.INF, layout1.inf, layout2.inf DriverVer = 11/16/2001, 1.0.8 ;CatalogFile=NVCAP.CAT [DestinationDirs] nvcap.CopyDrivers=10,system32\drivers ; eg. \windows\system32\drivers nvcap.CopyCodec=11 [SourceDisksNames] 1=%Disk1Name%,,,%10% [SourceDisksFiles] nvcap.sys=1,system32\drivers [Manufacturer] %MS%=MS [MS] %nvcap.DeviceDesc%=nvcap.Device,DISPLAY\nvcap ;------------------------------------------------------------------------------- [nvcap.Device] Include = ks.inf, kscaptur.inf, ksfilter.inf Needs= KS.Registration,KSCAPTUR.Registration,MSPCLOCK.Ins tallation AddReg = nvcap.AddReg UpdateInis= nvcap.UpdateIni CopyFiles= nvcap.CopyDrivers, nvcap.CopyCodec DelFiles = nvcap.DelDrivers KnownFiles= nvcap.KnownFiles [nvcap.Device.NT] Include = ks.inf, kscaptur.inf, ksfilter.inf Needs= KS.Registration,KSCAPTUR.Registration.NT,MSPCLOCK. Installation AddReg = nvcap.AddReg UpdateInis= nvcap.UpdateIni CopyFiles= nvcap.CopyDrivers, nvcap.CopyCodec DelFiles = nvcap.DelDrivers [nvcap.CopyDrivers] ;nvcap.sys stream.sys [nvcap.CopyCodec] msyuv.dll [nvcap.UpdateIni] system.ini, drivers32,,"VIDC.UYVY=msyuv.dll" [nvcap.KnownFiles] nvcap.sys=safe [nvcap.DelDrivers] ;--------------------------------------------------------------- ; Decoder related values ; All values in the decoder key and subkeys are string values ;--------------------------------------------------------------- [nvcap.AddReg] HKR,,DevLoader,,*NTKERN HKR,,NTMPDriver,,nvcap.sys ;/////////////nVidia Customizations////////////////////////////// ; ; Please read this !!!!!!!!!!!!!!!!!!!!!!!!!! ; Is video input does not switch correctly or ; audio doesn't mute, most probably the settings here are ; incorrect. ; ; 1)If an input source(PhilComp, PhilTuner etc) is removed, ; it won't be enumerated by the capture driver. ; Ex. If you do not want TUNER support for the All-in-one design ; remove "HKR,,AIOTuner,,VINX" key and Tuner input won't be ; enumerated. ; ;//////////////////////////////////////////////////////////////// ;----Customization for external tuner box----------------------- ; This is the translucent green box ;--------------------------------------------------------------- HKR,,PhilComp,,VIN0 ; input sel for ext. tuner (philips) design HKR,,PhilTuner,,VIN0 HKR,,PhilSVideo,,VIN6 ;----Customization for the ALL-In-One design-------------------- HKR,,AIOComp,,VIN0 ; input sel for all-in-1 HKR,,AIOSVideo,,VIN6 ;----Customization for the Micronas VPX chipsets---------------- HKR,,VPXComp,,VIN2 ; input sel for ext. tuner (micronas) design HKR,,VPXTuner,,VIN1 HKR,,VPXSVideo,,VIN3 HKR,,DefaultIn,,Comp HKR,,ExtSwitch,,FALSE HKR,,Manufacturer,, ;--------------------------------------------------------------- ; Subkey for VidComp ; 8574=W/46/ff ; 8575=W/46/ff/3 ;--------------------------------------------------------------- HKR,VidComp,NumCmd,,1 HKR,VidComp,Cmd0,,W/46/ff ;--------------------------------------------------------------- ; Subkey for VidSVid ; 8574=W/46/bf ; 8575=W/46/ff/2 ;--------------------------------------------------------------- HKR,VidSVid,NumCmd,,1 HKR,VidSVid,Cmd0,,W/46/bf ;--------------------------------------------------------------- ; Subkey for VidTuner ; 8574=W/46/7f ; 8575=W/46/ff/1 ;--------------------------------------------------------------- HKR,VidTuner,NumCmd,,1 HKR,VidTuner,Cmd0,,W/46/7f ;--------------------------------------------------------------- ; Subkey for AudTuner ;--------------------------------------------------------------- HKR,AudTuner,NumCmd,,0 ;--------------------------------------------------------------- ; Subkey for AudLineIn ;--------------------------------------------------------------- HKR,AudLineIn,NumCmd,,0 ;--------------------------------------------------------------- ; Subkey for AudMute ; 9850 = W/b6/6/18 ; 9874 = W/b0/12/ff ; 9873 = W/b4/0/40 ;--------------------------------------------------------------- HKR,AudMute,NumCmd,,0 ;HKR,AudMute,Cmd0,,W/b6/6/18 ;--------------------------------------------------------------- ; Subkey for AudUnMute ; 9850 = W/b6/6/40 ; 9874 = W/b0/12/fb ; 9873 = W/b4/0/90 ;--------------------------------------------------------------- HKR,AudUnMute,NumCmd,,0 ;HKR,AudUnMute,Cmd0,,W/b6/6/40 ;--------------------------------------------------------------- ; Subkey for board customization ;--------------------------------------------------------------- HKR,Custom,NumCmd,,1 HKR,Custom,Cmd0,,W/46/3f ;///////////End of nVidia Customization////////////////////////// ;////////////////Philips HAL customization/////////////////////// HKR,,Address,,0x4a ; I2C address only important if ; VideoDecoder != AUTO HKR,,InterfaceType,,D1 ; "D1" (8 bit) or "DMSD16" (16 bit) HKR,,VideoDecoder,,AUTO ; "SAA7111", "SAA7111A", "SAA7112V0", ; "SAA7112", "SAA7113V0", "SAA7113", ; "SAA7113A", "SAA7114", "AUTO" HKR,,VideoStandard,,PAL ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" HKR,,OutputFormat,,CCIR656 ; "YUV422", "YUV411", "YUV420", ; "YUV410", "YUV9", "RGB565", ; "RGB888", "CCIR656" HKR,,VBIMode,,RAW ; "RAW", "BASEBAND" (optinal) HKR,,VBILineWidth,,720 ; only needed if VBIMode used HKR,,VBILineOffset,,0 ; only needed if VBIMode used HKR,,EnableSlicer,,0 ; Enable slicer if it is present HKR,,Oversample,,4 ; 4..Use Philips 27MHz Frequency ; 5..Use 5x for old Microsoft CC- & NABTS Codecs ;--------------------------------------------------------------- ; Subkey for video source 1 ;--------------------------------------------------------------- HKR,VidSrc1,InputMode,,0 HKR,VidSrc1,SourceType,,VCR HKR,VidSrc1,VideoType,,Composite HKR,VidSrc1,ScalerFID,,DEFAULT HKR,VidSrc1,ScalerMode,,DEFAULT ;--------------------------------------------------------------- ; Subkey for video source 2 ;--------------------------------------------------------------- HKR,VidSrc2,InputMode,,0 HKR,VidSrc2,SourceType,,TV HKR,VidSrc2,VideoType,,Tuner HKR,VidSrc2,ScalerFID,,DEFAULT HKR,VidSrc2,ScalerMode,,DEFAULT ;--------------------------------------------------------------- ; Subkey for video source 3 ;--------------------------------------------------------------- HKR,VidSrc3,InputMode,,6 HKR,VidSrc3,SourceType,,VCR HKR,VidSrc3,VideoType,,SVHS HKR,VidSrc3,ScalerFID,,DEFAULT HKR,VidSrc3,ScalerMode,,DEFAULT ;--------------------------------------------------------------- ; Subkey Description for video sources (optional) ;--------------------------------------------------------------- ; Subkeyname : "VidSrcX" - X = number of input ; InputMode : Decoder input mode for video source ("0" to "9") ; SourceType : "Camera", "TV", "VCR" ; VideoType : "Tuner", "Composite", "SVHS", "Extern_1" ; ScalerFID : "DEFAULT", "INVERT" (optional) ; ScalerMode : "DEFAULT", "HIGH_BANDWIDTH", "LOW_BANDWIDTH" (optional) ;--------------------------------------------------------------- ; Subkey Description for teletext sources (optional) ;--------------------------------------------------------------- ; Subkeyname : "TelSrcX" - X = number of input ; InputType : "INTERNAL", ""EXTERNAL_1" ;--------------------------------------------------------------- ; Subkey example for teletext source (optional) ;--------------------------------------------------------------- ; HKR,TelSrc1,InputType,,INTERNAL ;--------------------------------------------------------------- ; Subkey Description for default values (optional) ;--------------------------------------------------------------- ; Subkeyname: "DefaultSaa7111" for defaults of Saa7111 ; "DefaultSaa7111A" for defaults of Saa7111A ; "DefaultSaa7112V0" for defaults of Saa7112V0 ; "DefaultSaa7112" for defaults of Saa7112 ; "DefaultSaa7113V0" for defaults of Saa7113V0 ; "DefaultSaa7113" for defaults of Saa7113 ; "DefaultSaa7113A" for defaults of Saa7113A ; "DefaultSaa7114" for defaults of Saa7114 ; Reg0xXXX : Value of register 0xXXX (hex) overwriting the ; value in the hardcoded default array. The register ; number in the key must be hex with leading 0x and ; must contain 3 digits! ;--------------------------------------------------------------- ; Subkey for default values for the Saa7113 ; The hardcoded default value 0x82 of register 0x40 is replaced ; with 0x02 which is necessary for PAL ;--------------------------------------------------------------- HKR,DefaultSaa7113,Reg0x040,,0x02 HKR,DefaultSaa7113V0,Reg0x040,,0x02 ;--------------------------------------------------------------- ; Subkey for default values for the Saa7114 ; The hardcoded default value 0x00 of register 0x80 is replaced ; with 0x10 which is necessary for NTSC sliced data interface ;--------------------------------------------------------------- ;HKR,DefaultSaa7114,Reg0x080,,0x40 ;only when EnableSlicer=1 !!! ;/////////////////End of Philips HAL customization////////////// [nvcap.Device.Interfaces] AddInterface={65e8773d-8f56-11d0-a3b9-00a0c9223196},"GLOBAL",VideoCapture, AddInterface={a799a801-a46d-11d0-a18c-00a02401dcd4},"GLOBAL",VideoCrossbar, [nvcap.Device.NT.Interfaces] AddInterface={65e8773d-8f56-11d0-a3b9-00a0c9223196},"GLOBAL",VideoCapture, AddInterface={a799a801-a46d-11d0-a18c-00a02401dcd4},"GLOBAL",VideoCrossbar, [VideoCapture] AddReg=VideoCapture.AddReg [VideoCrossbar] AddReg=VideoXBar.AddReg [VideoCapture.AddReg] HKR,,CLSID,,{17CCA71B-ECD7-11D0-B908-00A0C9223196} HKR,,FriendlyName,,%nvcap.Capture% HKR,,PageOutWhenUnopened,1,01 HKR,,DontSuspendIfStreamsAreRunning,1,01 [VideoXBar.AddReg] HKR,,CLSID,,{71F96460-78F3-11d0-A18C-00A0C9118956} HKR,,FriendlyName,,%nvcap.Crossbar% [nvcap.Device.NT.Services] AddService = nvcap,0x00000002,nvcap.ServiceInstall [nvcap.ServiceInstall] DisplayName = %nvcap.DeviceDesc% ServiceType = %SERVICE_KERNEL_DRIVER% StartType = %SERVICE_AUTO_START% ErrorControl = %SERVICE_ERROR_NORMAL% ServiceBinary = %12%\nvcap.sys ;--------------------------------------------------------------- ; S t r i n g s ;--------------------------------------------------------------- [Strings] ;---------------- ; Non-Localizable ;---------------- SERVICE_KERNEL_DRIVER=1 SERVICE_AUTO_START=2 SERVICE_ERROR_NORMAL=1 ;---------------- ; Localizable ;---------------- Msft = "nVidia Corporation" MS = "nVidia" captureClassName = "Sound, video and game controllers" nvcap.DeviceDesc = "nVidia WDM Video Capture (universal)" nvcap.Capture = "nVidia WDM Video Capture (universal)" nvcap.Crossbar = "nVidia WDM Video Crossbar (universal)" Disk1Name = "nVidia WDM Drivers Disk 1" ################################################## ####################################### -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( Thanks for this it all seems to be looking exactly like my one here as I first changed mine to PAL (in nvcap.inf file) and then reinstalled the nvcap.inf by right clicking and choosing Install on the menu "and" I also tried tweaking nvcap.inf first then installing the whole WDM driver package and even though it appears to be set to PAL in the registry, it still reverts to NTSC_M each time.... Anyways, I'll reboot now that I've messed with the registry and see if it works this time and I'll repost back as to what happens thanks |
#9
|
|||
|
|||
One problem solved it seems
It appears that now I have changed the registry to PAL it has rebooted and it has miraculously set itself to PAL_B mode!!!! so I am guessing that PAL_I was some similar standard that seemed to work for me but the real one is PAL_B and now the picture is properly centred so my sincere thanks for the help now I just have to sort out why I can't capture any frames at all in VirtualDub (see problem 2 in my other post: Subject: GeforceFX 5900XT VTD128 card gives picture but not capturing video at all) and I will be all set..... lol the joy of computers and their many errors, eh? "Granulated" wrote in message ... On Fri, 13 Aug 2004 01:19:39 +0100 "NeonBlue" meeped : HKR,,VideoStandard,,PAL_I ; "NTSC", "PAL", "SECAM", ; "NTSC_433_50", "NTSC_433_60", ; "NTSC_N", "PAL_433_60", "PAL_N", ; "PAL_M", "AUTO" WHy did you put PAL_I ? it's not even in the list ! I -- ) ___ ______ (__/_____) /) (, / ) / __ _ (/ _ /---( __ _/_ _ / (_(_/ (_(__/ )_(_(_ ) / ____)(_(_/ (_(__/_)_ (______) (_/ ( |
#10
|
|||
|
|||
Hi NeonBlue I am facing the exact same problem with my NVidia Personal Cinema GeForce FX 5700. I have tried changing the nvcap.inf file, installing it or reinstalling WDM with modified inf file but no luck. For me, I am not even able to modify the TV tuner type with any application. Can you please tell me which registry setting you changed to solve the problem? Thanks -- paluser ------------------------------------------------------------------------ paluser's Profile: http://extremetechsupport.com/forum/...ml?userid=1525 View this thread: http://extremetechsupport.com/forum/....phtml?t=57296 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Video capture with ATI TV Video Wonder | Thomas Gill | Ati Videocards | 0 | December 21st 04 07:39 AM |
pc problems after g card upgrade + sp2 | ben reed | Homebuilt PC's | 9 | November 30th 04 01:04 AM |
X800 and video capture one more time | WhoKnows | Ati Videocards | 5 | November 22nd 04 02:50 AM |
Need help overclocking Barton 2500+ on AsRock K7VM4 and video capture questions | Bill | Nvidia Videocards | 7 | November 21st 03 06:25 PM |
"Double" Sound or no sound on video capture | Jess | Ati Videocards | 0 | August 7th 03 11:19 PM |