If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Memory and new Mobo Question for beginner
Hi,
I am about to get a new Mobo and ram to go with other bits I have managed to get together to make a half decent system. To get either an MSI 865pe neo 2 800mhz fsb or Abit IC7 Max 3 What would be the best memory to get for this. What is the difference about "Low Latency memory"? I have heard that some memory won't work on Intel chipsets!! Is this correct? I have not a clue about mem and don't want to buy and get it wrong. System consists of so far. P4 2.8c (not 800mhz or HT) MSI 845pe Max 2 533mhz fsb 768MB DDR PC 2100 ram 266mhz (can this be clocked?) Sapphire x800 pro 256mb 2 x 80GB Seagate Barracuda 2mb cache DVD CD-RW Q-tec 550W power Thermaltake Xaser3 Super Tower Zalman Reserator 1 with VGA Block running @25 degrees CPU Temp Any advice would be greatly appreciated with a beer Spence |
#2
|
|||
|
|||
I am about to get a new Mobo and ram to go with other bits I have managed to
get together to make a half decent system. To get either an MSI 865pe neo 2 800mhz fsb or Abit IC7 Max 3 Memory will match the FSB speed at some multiple. So if your FSB is 800 MHz get 400 MHz RAM, which is PC3200. Your mobo will say if it needs to be buffered, ECC, etc., but for most people they want unbuffered non-ECC. If you get the 533 FSB mobo, get PC2100 RAM, which is 266 MHz. You can mismatch to an extent - i.e. put 266 MHz RAM into a mobo with 400 FSB, but some mobos reject it. So just decide which mobo you are getting then get the corresponding RAM. What is the difference about "Low Latency memory"? It runs faster. Some people won't ever notice. 3D gamers might notice. I honestly can't tell sometimes. But if you have an extra $20-30 per stick to spend, the low latency might make you happier. P4 2.8c (not 800mhz or HT) MSI 845pe Max 2 533mhz fsb 768MB DDR PC 2100 ram 266mhz (can this be clocked?) Do you mean OVERclocked? |
#3
|
|||
|
|||
Hi David,
Thanks for the reply it clears up a few things before I go out and spend. I am aiming toward the MSI 865pe due to never having any problems with any of the MSI boards I have had in the past. And yes, I do mean overclocked for the 2100 ram. Spencer "David Besack" wrote in message ... I am about to get a new Mobo and ram to go with other bits I have managed to get together to make a half decent system. To get either an MSI 865pe neo 2 800mhz fsb or Abit IC7 Max 3 Memory will match the FSB speed at some multiple. So if your FSB is 800 MHz get 400 MHz RAM, which is PC3200. Your mobo will say if it needs to be buffered, ECC, etc., but for most people they want unbuffered non-ECC. If you get the 533 FSB mobo, get PC2100 RAM, which is 266 MHz. You can mismatch to an extent - i.e. put 266 MHz RAM into a mobo with 400 FSB, but some mobos reject it. So just decide which mobo you are getting then get the corresponding RAM. What is the difference about "Low Latency memory"? It runs faster. Some people won't ever notice. 3D gamers might notice. I honestly can't tell sometimes. But if you have an extra $20-30 per stick to spend, the low latency might make you happier. P4 2.8c (not 800mhz or HT) MSI 845pe Max 2 533mhz fsb 768MB DDR PC 2100 ram 266mhz (can this be clocked?) Do you mean OVERclocked? |
#4
|
|||
|
|||
Theres no reason to not buy the 800 fsb motherbord,they can be found for less
than $100 a 865 chipset board. The 800 FSB makes for a much faster system than a 533 FSB. Also i would get some PC 433 3500mhz ram, KINGSTON HYPER X or Corsair the 800 FSB MB will easily overclock to 225 FSB. DOUG |
#5
|
|||
|
|||
Thanks for the reply it clears up a few things before I go out and spend. I
am aiming toward the MSI 865pe due to never having any problems with any of the MSI boards I have had in the past. And yes, I do mean overclocked for the 2100 ram. Well, the best thing you can do with RAM is buy faster RAM and clock to THAT speed. There's almost NO difference in price between 512MB of PC2100 and PC3200. Though - if you get the 800 FSB board, and would normally get PC3200 RAM (400 MHz), you could always get PC3500 RAM for future overclockability. |
#6
|
|||
|
|||
Ya, but you are all forgetting that he does not have any 800fsb CPU.
He has a 2.8NW 533. So, getting to 225fsb is tricky I would suggest buy the best mobo you can with the 865PE chipset, then buying some real nice memory.. Don't buy Kingston HyperX if you plan to overclock. Buy some GEIL or OCZ PC3500/3700 memory. Then, exchange that 533 cpu with a really faster 800 HT one ------------------------------------------------------- Stormgiant Asus P4P800-Deluxe NW3000@3915 FSB261 on WC 512MB OCZ BH-5 @DDR522 2-2-2-5 Power Color ATi 9800XT 520/410 ------------------------------------------------------- On 30 Jun 2004 23:40:23 GMT, (Courseyauto) wrote: Theres no reason to not buy the 800 fsb motherbord,they can be found for less than $100 a 865 chipset board. The 800 FSB makes for a much faster system than a 533 FSB. Also i would get some PC 433 3500mhz ram, KINGSTON HYPER X or Corsair the 800 FSB MB will easily overclock to 225 FSB. DOUG |
Thread Tools | |
Display Modes | |
|
|