If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
UPS with a " I don't want it to beep' option
The cable that you need originally came with the UPS. GUARANTEED
(unless the UPS was not truly new and sealed, e.g. if it was "open box"). But, that said, APC is absolutely idiotic for not just using standard USB sockets on their UPS'. All of the APC UPS' that I have (500VA, 725VA and 1,500VA) can be programmed not to beep; some of the earlier models with serial port interfaces cannot be so programmed. I THINK that all models with USB ports can be programmed. Many of the low end UPS' with 300-350VA ratings have what I call "toy batteries" .... 12 volts at THREE amp-hours. Many of these are in a compartment originally intended for the very standard 12 volt 7AH batteries, with insert fins molded into the compartment for the smaller battery. A little bit of work with some plastic cutting tools will enable you to upgrade those units to the larger 7AH battery (it's pretty obvious when you can and cannot do this). I've been told, but cannot verify, that the 350VA units are actually the same as the 500VA units except for the smaller battery. - Bobb - wrote: I grabbed the APC UPS (ES350U) from the living room and went to hook it up to my PC to program it - and NOW I remember why I didn't install the software. For me to connect the UPS to be able to program it , I need to buy a USB to RJ45 cable for $39. That's why I never did it ! I paid $30 to buy the UPS - I'm not gonna pay $39 to talk to it ! SO, I just came from BestBuy. They have a Cyperpower 550VA UPS on sale for $35 - with a cable and software. I'll program IT, put it in the living room and then unplug it a few times to see if it 'remembers' to not beep. If that works OK, I'll then use the 350VA APC UPS for the PC and just turn it off when I lose power. If it doesn't work , I'll disconnect the pseaker in the APC and return the CP UPS to Best Buy. William - I had looked before at APC for schematics. I'm with you - disconnect the speaker and put a note on it to remind myself in case I ever DO want it to beep. Thanks guys. "William R. Walsh" m wrote in message news:04tmi.11934$Xa3.3087@attbi_s22... Hi! APC markets some units that can be told not to beep at all. The BR1500LCD and BR1300LCD models can both have their beepers configured to stay off. You can find at least the 1500 model for sale at Best Buy in the US. It is advertised as a "Back UPS XS" there. Price is around $144. For your existing UPS units, a little circuit modification might be in order. I have "muted" various UPS units in times past by opening them up (unplug the unit, disconnect the batteries FIRST and *be careful* -- these things contain hazardous parts that may store energy even after the battery is disconnected) and removing the offending beeper. This is effective but it will invalidate any warranty your UPS is under. William |
#12
|
|||
|
|||
UPS with a " I don't want it to beep when lose power' option
For APC models that have USB ports, the "silence" programming is in the
UPS. If you connect it to a PC and tell it to be silent, it will remain silent thereafter whether connected to the PC or not, at least as long as there isn't a total loss of all power to the UPS (e.g. battery becomes completely discharged). - Bobb - wrote: Rank, Do you know ... If I hook each up to my PC, then program it , will those settings work WITHOUT a PC ? Or is it their software that controls it ( with a PC) via the external cable ? Would you know: if I program it - after the batteries discharge will it 'remember' or need to reprogram it each time ? I couldn't find that answer at apc.com I'll check their site again, but I remember scrolling thru their Knowledge Base until I was seeing W98/NT issues - pre my models and found no info on 'ALARM' Thanks |
#13
|
|||
|
|||
UPS with a " I don't want it to beep when lose power' option
"Willard Sandilands" wrote in message . net... For APC models that have USB ports, the "silence" programming is in the UPS. If you connect it to a PC and tell it to be silent, it will remain silent thereafter whether connected to the PC or not, at least as long as there isn't a total loss of all power to the UPS (e.g. battery becomes completely discharged). For the Cyberpower I bought - that's how it looked. I installed sw on a backup image ( so it doesn't show ( not connected every time I boot), , hooked up USB2 cable, chose " Disable all alerts" and shutdown pc - hooked up the UPS in living room and when I unplugged it / back in - no beep - great! (My APC had only rj45 and 2 rj12 jacks) Thanks - Bobb - wrote: Rank, Do you know ... If I hook each up to my PC, then program it , will those settings work WITHOUT a PC ? Or is it their software that controls it ( with a PC) via the external cable ? Would you know: if I program it - after the batteries discharge will it 'remember' or need to reprogram it each time ? I couldn't find that answer at apc.com I'll check their site again, but I remember scrolling thru their Knowledge Base until I was seeing W98/NT issues - pre my models and found no info on 'ALARM' Thanks |
#14
|
|||
|
|||
UPS with a " I don't want it to beep when lose power' option
Bobb
If you want one of those RJ45 to USB cables, let me know. I've ended up with several that I don't use, not even sure if I still have UPSs around that they go to. Remove the obvious from my reply email. Val |
#15
|
|||
|
|||
UPS
Thanks Val,
If others say " I got one", then it's here - somewhere. I'll check and let you know if I do need one. Thanks for the offer. "Val" wrote in message ... Bobb If you want one of those RJ45 to USB cables, let me know. I've ended up with several that I don't use, not even sure if I still have UPSs around that they go to. Remove the obvious from my reply email. Val |
#16
|
|||
|
|||
UPS with a " I don't want it to beep' option
Willard Sandilands writes:
The cable that you need originally came with the UPS. GUARANTEED (unless the UPS was not truly new and sealed, e.g. if it was "open box"). But, that said, APC is absolutely idiotic for not just using standard USB sockets on their UPS'. They seem to have changed. The one I'm using now does indeed have a standard USB B jack on it. No special cable needed. Dave |
#17
|
|||
|
|||
UPS with a " I don't want it to beep when lose power' option
- Bobb - wrote:
I can't be the only one with this issue and can't find an alternative. Advice? Different vendor? I've got a few of these home-office-sized UPS 350VA, 500VA from APC and when I lose power at the house, I CANNOT turn off the #$%'ing beeping noise! Store-purchasable UPS's are intended ONLY for computing equipment and NOT for ANYTHING ELSE. They do not produce anything even resembling clean power, but only a 60Hz, 120v SQUARE WAVE, which could do DAMAGE to non-computing equipment. If you have and require life-sustaining equipment that requires uninterruptible power, I suggest you get something from the local power company instead of the electronics store. If you have anything other than computing equipment connected to power through a store-purchasable UPS I suggest you remove it from the UPS—for the equipment's own sake. The proper use of store-purchasable UPS's is to connect computing equipment that has on-board data-storage capacity through the UPS's battery back-up. The proper procedure in case of power-outage is to IMMEDIATELY SHUT-DOWN that computing equipment properly—then TURN OFF the UPS. When you do this, the beeping will stop. If you are using store-purchasable UPS's for anything other than computing equipment you are MISUSING those UPS's and putting your equipment in danger of damage FROM THE UPS. If you insist on continuing such practices, then you are displaying your own stubbornness and stupidity—and you deserve what you get. __________________________________________________ _____________________________ http://www.lulu.com/billsey |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Toshiba Laptop suddenly "loses" wall power | [email protected] | General | 5 | March 13th 07 08:08 AM |
P5GD2 BIOS does not show "Chassis Q-Fan Control" option | [email protected] | Asus Motherboards | 0 | June 1st 06 05:05 PM |
Power surge killed iiyama 18" TFT, any comments on Dell 20" offer | John Perry | UK Computer Vendors | 21 | January 12th 06 04:42 PM |
A7V133-VM + PCI video = BEEP BEEP BEEP BEEP? | Lost | Asus Motherboards | 2 | November 13th 03 05:33 AM |