If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
epson EPL-5800L has gone nut
I have a laser printer from epson (EPL-5800L)
that has gone nut. It prints blank pages ... it stops paper in the middle but there is no paper jam ... it prints correctely, then goes nut again ... I check even the sensors, I tried every version of driver for win, mac, linux ... same behaviour, so it's hardware or maybe a firmware problem. So, the question is ... how can I update the firmware (or reload the same version)? Is there a CD somewhere for this model. I checked everywhere but I found nothing, so it's probably just one of the CD given to repair shops. Any help would be very appreciated. |
#2
|
|||
|
|||
epson EPL-5800L has gone nut
From: "Tano Cariddi"
I have a laser printer from epson (EPL-5800L) that has gone nut. It prints blank pages ... it stops paper in the middle but there is no paper jam ... it prints correctely, then goes nut again ... I check even the sensors, I tried every version of driver for win, mac, linux ... same behaviour, so it's hardware or maybe a firmware problem. So, the question is ... how can I update the firmware (or reload the same version)? Is there a CD somewhere for this model. I checked everywhere but I found nothing, so it's probably just one of the CD given to repair shops. Any help would be very appreciated. Is this 13 years old / Are the error and ready lights flashing ? If yes, how ? -- Dave Multi-AV Scanning Tool - http://multi-av.thespykiller.co.uk http://www.pctipp.ch/downloads/dl/35905.asp |
#3
|
|||
|
|||
epson EPL-5800L has gone nut
On 04/30/2013 07:01 PM, David H. Lipman wrote: From: "Tano Cariddi"
I have a laser printer from epson (EPL-5800L) that has gone nut. It prints blank pages ... it stops paper in the middle but there is no paper jam ... it prints correctely, then goes nut again ... I check even the sensors, I tried every version of driver for win, mac, linux ... same behaviour, so it's hardware or maybe a firmware problem. So, the question is ... how can I update the firmware (or reload the same version)? Is there a CD somewhere for this model. I checked everywhere but I found nothing, so it's probably just one of the CD given to repair shops. Any help would be very appreciated. Is this 13 years old / Are the error and ready lights flashing ? If yes, how ? It works as it is everything fine .... it signal with a red led when paper is jammed, but nothing else. If you print a single page, after doing that it takes another page just to jam it ... the only thing I can think about is that firmware somhow has been currupted. All the sensors are good, I tested them. |
#4
|
|||
|
|||
epson EPL-5800L has gone nut
From: "Tano Cariddi"
On 04/30/2013 07:01 PM, David H. Lipman wrote: From: "Tano Cariddi" I have a laser printer from epson (EPL-5800L) that has gone nut. It prints blank pages ... it stops paper in the middle but there is no paper jam ... it prints correctely, then goes nut again ... I check even the sensors, I tried every version of driver for win, mac, linux ... same behaviour, so it's hardware or maybe a firmware problem. So, the question is ... how can I update the firmware (or reload the same version)? Is there a CD somewhere for this model. I checked everywhere but I found nothing, so it's probably just one of the CD given to repair shops. Any help would be very appreciated. Is this 13 years old / Are the error and ready lights flashing ? If yes, how ? It works as it is everything fine .... it signal with a red led when paper is jammed, but nothing else. If you print a single page, after doing that it takes another page just to jam it ... the only thing I can think about is that firmware somhow has been currupted. All the sensors are good, I tested them. If the firnware was corrupted it definitely would generate eror codes or not work in any fashion at all. -- Dave Multi-AV Scanning Tool - http://multi-av.thespykiller.co.uk http://www.pctipp.ch/downloads/dl/35905.asp |
#5
|
|||
|
|||
epson EPL-5800L has gone nut
It works as it is everything fine .... it signal with a red led
when paper is jammed, but nothing else. If you print a single page, after doing that it takes another page just to jam it ... the only thing I can think about is that firmware somhow has been currupted. All the sensors are good, I tested them. If the firnware was corrupted it definitely would generate eror codes or not work in any fashion at all. The thing is you have a printer that could print one, two, three ... pages without any problem ... then keep going printing white pages until paper jams. Other times it prints one page ... than two/three white pages .. then another good one ... and again white pages. It's a wacky behaviour. My bet is on something software related, but not at OS level (it does the same in windows, linux and OSX) but at low level (firmware). What do they use in the repair center? Is there a kind of cd test that could be use to diagnose what it's wrong ? |
#6
|
|||
|
|||
epson EPL-5800L has gone nut
From: "Tano Cariddi"
It works as it is everything fine .... it signal with a red led when paper is jammed, but nothing else. If you print a single page, after doing that it takes another page just to jam it ... the only thing I can think about is that firmware somhow has been currupted. All the sensors are good, I tested them. If the firnware was corrupted it definitely would generate eror codes or not work in any fashion at all. The thing is you have a printer that could print one, two, three ... pages without any problem ... then keep going printing white pages until paper jams. Other times it prints one page ... than two/three white pages .. then another good one ... and again white pages. It's a wacky behaviour. My bet is on something software related, but not at OS level (it does the same in windows, linux and OSX) but at low level (firmware). What do they use in the repair center? Is there a kind of cd test that could be use to diagnose what it's wrong ? You test the printer at the simplest level so you take tghe OS out of the equation. For example load a DOS disk and have a simple stream of continuous text or PCL sent to the printer and/or continuous print self-test pages, etc. -- Dave Multi-AV Scanning Tool - http://multi-av.thespykiller.co.uk http://www.pctipp.ch/downloads/dl/35905.asp |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Epson Smart Panel Software Version 2.5 for the Epson perfection 1660 | junoman | Printers | 5 | May 26th 09 10:56 PM |
Looking for a good HP/Epson printer that is similar to Epson Stylus Photo 785EPX... | [email protected] | Printers | 11 | November 15th 04 02:04 AM |
REQ Epson 1280 Technical/service Manual EPTM-SP1280 Epson says no longer avaiable | Sally | Printers | 4 | December 12th 03 05:58 PM |
Epson Perfection 1200 Film Adapter - Will It Work With An Epson GT 7000 ? | WhiteDwarf500 | Scanners | 1 | November 13th 03 10:43 AM |
Epson Stylus C62 - Poor print quality. Epson Refusing Upgrade. | eric | Printers | 6 | August 1st 03 12:04 AM |