|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
September 12th 06, 05:37 AM
posted to alt.comp.periphs.mainboard.asus
|
|||
|
|||
Replacing P4P800 SE with RAID0
I had a P4P800 SE motherboard go bad. The POST wouldn't run. However
the CPU and video card both worked in another machine. I've replaced this motherboard with another P4P800 SE. When I configure it for RAID in the BIOS and I run the RAID setup Ctrl-I it seems to recognize the existing RAID volume. The problem is that it won't boot from the RAID array. I guess I'm wondering how I go about getting this to work. Thanks, Brad 
|
|
#2
September 12th 06, 06:46 AM
posted to alt.comp.periphs.mainboard.asus
|
|||
|
|||
|
Replacing P4P800 SE with RAID0
I have the same board not running raid but I think I read that you have to
load drivers for the raid. I will check later if and when I can find my manual. "Brad Quinn" wrote in message oups.com... I had a P4P800 SE motherboard go bad. The POST wouldn't run. However the CPU and video card both worked in another machine. I've replaced this motherboard with another P4P800 SE. When I configure it for RAID in the BIOS and I run the RAID setup Ctrl-I it seems to recognize the existing RAID volume. The problem is that it won't boot from the RAID array. I guess I'm wondering how I go about getting this to work. Thanks, Brad
|
|
#3
September 12th 06, 07:07 AM
posted to alt.comp.periphs.mainboard.asus
|
|||
|
|||
|
Replacing P4P800 SE with RAID0
Thanks Jim but I don't think that's the problem.
Before replacing the motherboard this was a bootable RAID 0 volume. I had already installed XP using the RAID driver from floppy. My hope was that the RAID volume would simply be recognized and everything would just work. Failing that I was hoping that there might be some BIOS level utility that would allow me to reconstruct the RAID volume information. BigJim wrote: I have the same board not running raid but I think I read that you have to load drivers for the raid. I will check later if and when I can find my manual. "Brad Quinn" wrote in message oups.com... I had a P4P800 SE motherboard go bad. The POST wouldn't run. However the CPU and video card both worked in another machine. I've replaced this motherboard with another P4P800 SE. When I configure it for RAID in the BIOS and I run the RAID setup Ctrl-I it seems to recognize the existing RAID volume. The problem is that it won't boot from the RAID array. I guess I'm wondering how I go about getting this to work. Thanks, Brad
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Simple RAID 0, 1 ? from first time nubie... | kxdude4 | Homebuilt PC's | 27 | March 20th 06 02:56 AM |
| P4P800 Differences | XYZ | Asus Motherboards | 5 | January 21st 05 10:38 PM |
| Latest P4P800 Deluxe USB 2.0 W2K driver? | Daniel | Asus Motherboards | 4 | May 8th 04 12:11 AM |
| RAID0 with 2 scsi and 2 sata | dubOne | Asus Motherboards | 0 | May 7th 04 05:54 PM |
| P4p800 Deluxe, Sata Raid0 and Drive Image. Does it work?? | bert | Asus Motherboards | 6 | November 10th 03 12:16 AM |
Linear Mode
