If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
HP 1410 Printer Scanner
The Printer Scanner has been working fine for quite some time. But after
getting the cartridge refilled, the PSC 1410 prints only the Test Report in response to every command for printing a document. This has repeated at least 20 times. Is there any way to stop this and start getting documents printed as desired? There is no red light on any of the fault indicating light points. So what could be wrong with the system? P. Jayant -- Posted on news://freenews.netfront.net - Complaints to -- |
#2
|
|||
|
|||
HP 1410 Printer Scanner
Jayant" wrote in message
: The Printer Scanner has been working fine for quite some time. But after getting the cartridge refilled, the PSC 1410 prints only the Test Report in response to every command for printing a document. This has repeated at least 20 times. Is there any way to stop this and start getting documents printed as desired? There is no red light on any of the fault indicating light points. So what could be wrong with the system? When a new cartridge is installed the printer will print an alignment page. This page is then loaded onto the scanner bed and the scan button should be pressed to complete the alignment process. Check your manual for information on the alignment process. Until the alignment has been completed the printer will print an alignment page after each print job. Regards, Bob Headrick, MS MVP Printing/Imaging |
#3
|
|||
|
|||
HP 1410 Printer Scanner
On Nov 3, 10:42*pm, "Bob Headrick" wrote:
Jayant" wrote in message : The Printer Scanner has been working fine for quite some time. But after getting the cartridge refilled, the PSC 1410 prints only the Test Report in response to every command for printing a document. This has repeated at least 20 times. Is there any way to stop this and start getting documents printed as desired? There is no red light on any of the fault indicating light points. So what could be wrong with the system? When a new cartridge is installed the printer will print an alignment page. *This page is then loaded onto the scanner bed and the scan button should be pressed to complete the alignment process. *Check your manual for information on the alignment process. Until the alignment has been completed the printer will print an alignment page after each print job. Regards, Bob Headrick, MS MVP Printing/Imaging Thanks Mr. Headrick, for your informative reply. I shall remember this in future when I get a new or refilled cartridge. As mentioned by you, I have just now tried to print a document once again. The Printer printed the Alignment Test Report but not the doument I wanted to be printed. Anyway, I placed the Alignment sheet on the Scanner and pressed the Scan button and to make sure that the process was registered, even saved the scan in My Scans Folder. Then I tried again to print a document but still, the Printer does not wake up at all and start printing. P. Jayant |
#4
|
|||
|
|||
HP 1410 Printer Scanner
"p jayant" wrote in message : I have just now tried to print a document once again. The Printer printed the Alignment Test Report but not the document I wanted to be printed. Anyway, I placed the Alignment sheet on the Scanner and pressed the Scan button and to make sure that the process was registered, even saved the scan in My Scans Folder. Then I tried again to print a document but still, the Printer does not wake up at all and start printing. Hmm... the user manual is available at http://h10032.www1.hp.com/ctg/Manual/c00364973.pdf and the alignment procedure is shown on page 32. Some things to check: make sure you are using clean white paper and that the color cartridge is working properly - both the black cartridge and the cyan portion of the color cartridge must be working properly for the alignment to succeed. You also might try forcing an alignment from the Image Zone software if you have that installed on your system. Regards, Bob Headrick, MS MVP Printing/Imaging |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Canon F50 printer/scanner/fax - problem using scanner | [email protected] | Printers | 0 | February 6th 08 01:22 AM |
HP PSC 1410 printer. | Juan Bonet | General | 0 | September 10th 06 02:15 PM |
new PSC 1410 ... mmm | drd | Printers | 2 | December 31st 05 07:56 PM |
Scanner - Dell 922 All-in-one printer/scanner RevA01 not scanning but does print | Darren | Dell Computers | 4 | June 25th 05 04:58 PM |
Best inexpensive printer/scanner to replace Dell 942 printer/scanner? | fan | Printers | 4 | April 29th 05 02:01 AM |