A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » Printers
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

HP 1410 Printer Scanner



 
 
Thread Tools Display Modes
  #1  
Old November 3rd 08, 08:19 AM posted to comp.periphs.printers
P. Jayant
external usenet poster
 
Posts: 1
Default HP 1410 Printer Scanner

The Printer Scanner has been working fine for quite some time. But after
getting the cartridge refilled, the PSC 1410 prints only the Test Report in
response to every command for printing a document. This has repeated at
least 20 times. Is there any way to stop this and start getting documents
printed as desired? There is no red light on any of the fault indicating
light points. So what could be wrong with the system?

P. Jayant



-- Posted on news://freenews.netfront.net - Complaints to --
  #2  
Old November 3rd 08, 05:42 PM posted to comp.periphs.printers
Bob Headrick
external usenet poster
 
Posts: 535
Default HP 1410 Printer Scanner

Jayant" wrote in message
:

The Printer Scanner has been working fine for quite some time. But after
getting the cartridge refilled, the PSC 1410 prints only the Test Report in
response to every command for printing a document. This has repeated at
least 20 times. Is there any way to stop this and start getting documents
printed as desired? There is no red light on any of the fault indicating
light points. So what could be wrong with the system?


When a new cartridge is installed the printer will print an alignment
page. This page is then loaded onto the scanner bed and the scan button
should be pressed to complete the alignment process. Check your manual
for information on the alignment process.

Until the alignment has been completed the printer will print an
alignment page after each print job.

Regards,
Bob Headrick, MS MVP Printing/Imaging

  #3  
Old November 4th 08, 03:22 AM posted to comp.periphs.printers
p jayant
external usenet poster
 
Posts: 10
Default HP 1410 Printer Scanner

On Nov 3, 10:42*pm, "Bob Headrick" wrote:
Jayant" wrote in message

:

The Printer Scanner has been working fine for quite some time. But after
getting the cartridge refilled, the PSC 1410 prints only the Test Report in
response to every command for printing a document. This has repeated at
least 20 times. Is there any way to stop this and start getting documents
printed as desired? There is no red light on any of the fault indicating
light points. So what could be wrong with the system?


When a new cartridge is installed the printer will print an alignment
page. *This page is then loaded onto the scanner bed and the scan button
should be pressed to complete the alignment process. *Check your manual
for information on the alignment process.

Until the alignment has been completed the printer will print an
alignment page after each print job.

Regards,
Bob Headrick, MS MVP Printing/Imaging


Thanks Mr. Headrick, for your informative reply. I shall remember this
in future when I get a new or refilled cartridge. As mentioned by you,
I have just now tried to print a document once again. The Printer
printed the Alignment Test Report but not the doument I wanted to be
printed. Anyway, I placed the Alignment sheet on the Scanner and
pressed the Scan button and to make sure that the process was
registered, even saved the scan in My Scans Folder. Then I tried again
to print a document but still, the Printer does not wake up at all and
start printing.

P. Jayant
  #4  
Old November 4th 08, 05:53 AM posted to comp.periphs.printers
Bob Headrick
external usenet poster
 
Posts: 535
Default HP 1410 Printer Scanner



"p jayant" wrote in message
:

I have just now tried to print a document once again. The Printer
printed the Alignment Test Report but not the document I wanted to be
printed. Anyway, I placed the Alignment sheet on the Scanner and
pressed the Scan button and to make sure that the process was
registered, even saved the scan in My Scans Folder. Then I tried again
to print a document but still, the Printer does not wake up at all and
start printing.


Hmm... the user manual is available at
http://h10032.www1.hp.com/ctg/Manual/c00364973.pdf and the alignment
procedure is shown on page 32. Some things to check: make sure you are
using clean white paper and that the color cartridge is working properly
- both the black cartridge and the cyan portion of the color cartridge
must be working properly for the alignment to succeed.

You also might try forcing an alignment from the Image Zone software if
you have that installed on your system.

Regards,
Bob Headrick, MS MVP Printing/Imaging


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Canon F50 printer/scanner/fax - problem using scanner [email protected] Printers 0 February 6th 08 01:22 AM
HP PSC 1410 printer. Juan Bonet General 0 September 10th 06 02:15 PM
new PSC 1410 ... mmm drd Printers 2 December 31st 05 07:56 PM
Scanner - Dell 922 All-in-one printer/scanner RevA01 not scanning but does print Darren Dell Computers 4 June 25th 05 04:58 PM
Best inexpensive printer/scanner to replace Dell 942 printer/scanner? fan Printers 4 April 29th 05 02:01 AM


All times are GMT +1. The time now is 11:29 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2004-2022 HardwareBanter.
The comments are property of their posters.