|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
September 11th 06, 08:25 PM
posted to comp.periphs.printers
|
|||
|
|||
Printer refuses to print in langdscape format
My Brother 5270DN laserprinter refuses to print in landscape format even
when the necessery settings are chosen. Prints then in the standard portrait format! Any hints about what to do? Ben Notter 
|
|
#2
September 12th 06, 04:58 PM
posted to comp.periphs.printers
|
|||
|
|||
|
Printer refuses to print in langdscape format
Refuse to give it dessert until it behaves?
You may have a driver problem. Try removing and reinstalling it. Art notter wrote: My Brother 5270DN laserprinter refuses to print in landscape format even when the necessery settings are chosen. Prints then in the standard portrait format! Any hints about what to do? Ben Notter
|
|
#3
September 14th 06, 07:18 AM
posted to comp.periphs.printers
|
|||
|
|||
|
Printer refuses to print in landscape format
"Arthur Entlich" wrote in message news:2PANg.534176$iF6.201702@pd7tw2no... Refuse to give it dessert until it behaves? You may have a driver problem. Try removing and reinstalling it. Art Thanks for your advice. Reinstalled everything but problem still exists. Ben
|
|
#4
September 14th 06, 08:24 AM
posted to comp.periphs.printers
|
|||
|
|||
|
Printer refuses to print in landscape format
notter wrote: "Arthur Entlich" wrote in message news:2PANg.534176$iF6.201702@pd7tw2no... Refuse to give it dessert until it behaves? You may have a driver problem. Try removing and reinstalling it. Art Thanks for your advice. Reinstalled everything but problem still exists. It may be how you reinstalled the driver. First uninstall and do a cold boot. Then do a new install and do a cold boot. Make sure you use the disk that came with the device. Ben
|
|
#5
September 14th 06, 05:50 PM
posted to comp.periphs.printers
|
|||
|
|||
|
Printer refuses to print in landscape format
----- Original Message ----- From: "measekite" Newsgroups: comp.periphs.printers Sent: Thursday, September 14, 2006 9:24 AM Subject: Printer refuses to print in landscape format It may be how you reinstalled the driver. First uninstall and do a cold boot. Then do a new install and do a cold boot. Make sure you use the disk that came with the device. Done as advised but without result. I suppose one has sometimes to live with little inconveniences. Unless suddenly someone comes with the ultimate solution. Thanks for your support! Ben
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Seagate Barracuda 160 GB IDE becomes corrupted. RMA? | Dan_Musicant | Storage (alternative) | 79 | February 28th 06 08:23 AM |
| pc problems after g card upgrade + sp2 | ben reed | Homebuilt PC's | 9 | November 30th 04 01:04 AM |
| Cleaning Canon nozzles - i950 bubble jet. | DD | Printers | 30 | August 25th 04 01:19 PM |
| Optra R networking | JP | Printers | 1 | February 15th 04 11:35 PM |
| HELP: Can printer switch box cause printers to print garbage? | Zylan | Printers | 14 | February 15th 04 03:08 PM |
Linear Mode
