If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Cheap source of 60mm / Slot 1 CPU fans?
We need some for spares, finding them isn't a huge problem, but I'm having
a job finding them for less that £8 or so each, which seems a lot of money for something so basic.. any suggestions on a cheap source? I need the basic 60mm x 15mm 3-pin type that swrew onto a PII Slot 1 cooler. regards, Paul -- paul at spamcop.net |
#2
|
|||
|
|||
In message , Paul
Hutchings writes We need some for spares, finding them isn't a huge problem, but I'm having a job finding them for less that £8 or so each, which seems a lot of money for something so basic.. any suggestions on a cheap source? I need the basic 60mm x 15mm 3-pin type that swrew onto a PII Slot 1 cooler. regards, Paul Most slot 1 coolers I have ever seen were 50mm fans..?? -- njc AKA (Fastpay, Paypal & nochex e-mail) |
#3
|
|||
|
|||
On 15 Sep 2003 15:11:01 GMT, Paul Hutchings wrote:
We need some for spares, finding them isn't a huge problem, but I'm having a job finding them for less that £8 or so each, which seems a lot of money for something so basic.. any suggestions on a cheap source? I need the basic 60mm x 15mm 3-pin type that swrew onto a PII Slot 1 cooler. regards, Paul http://www.kingdomkomputers.co.uk/pr...roducts_id=157 |
#4
|
|||
|
|||
"nigel. carron" wrote in
: Most slot 1 coolers I have ever seen were 50mm fans..?? When I measured the whole diagonal it came out at around 57mm with around 50mm between the screwholes - I assumed it'd be 60mm, though I also imagine these things are standard in which case it's my mistake and we probably do need 50mm. I'll measure again tomorrow and if that's the case the link to KK looks promising - you reach a point where you dick about so long looking for a bargain that it costs more than going to RS to start with :-) regards Paul -- paul at spamcop.net |
#5
|
|||
|
|||
In message , Paul
Hutchings writes When I measured the whole diagonal it came out at around 57mm with around 50mm between the screwholes - I assumed it'd be 60mm, though I also imagine these things are standard in which case it's my mistake and we probably do need 50mm. I'll measure again tomorrow and if that's the case the link to KK looks promising - you reach a point where you dick about so long looking for a bargain that it costs more than going to RS to start with :-) Fans are always measured across sides - -- njc AKA (Fastpay, Paypal & nochex e-mail) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Can AC fans be used inside cases? | Phisherman | Homebuilt PC's | 37 | December 9th 04 01:46 AM |
Slot Fans | Ryan | Overclocking AMD Processors | 2 | May 2nd 04 03:52 PM |
Favorite Cheap Slot A mobo? | user | Overclocking AMD Processors | 6 | November 21st 03 07:54 PM |
Fan Controller and Fan causes floppy drive failure | Andrew Diamond | Overclocking | 25 | September 19th 03 07:51 AM |
Fan Controller and Fan causes floppy drive failure | Andrew Diamond | Overclocking AMD Processors | 16 | September 17th 03 06:56 AM |