If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Verify errors burning with liteon 52x burner and nero 5.5 & nero6
George R. wrote:
Hi, before i start here my config: WinXP Sp1, 384 MB Ram, Soyo Dragon+ board, AMD 1900+. I run Prime95 and memtest86 without any problems. My system is stable and kept well and up-to-date. I have one HD on IDE2 (Promise port), the CDRom on (Via) IDE0 and the Burner (Lite-On 52246S, latest firmware 6s0f) on (Via) IDE1. Every drive is on it's own IDE port and jumpered as master. All UDMA is on. I use 80 pin UDMA cables for all my drives. I even double checked and swapped my CDRom with the Burner today to see what happens. I can not burn ONE single error-free CD with this burner, using good TDK brand 48x CD-RWs. I even got down to burning at 4x speed to avoid errors, but still a no-go. Not even at 4x ! I first used Nero 5.5.10.42....now i got Nero 6 - still the same results. If i burn a typical, say ~500MB CD with lots of files i always get two or three files where Nero says "Verify error", the burned files don't match the ones on HD. When i burn a large ~500MB zip archive etc. then also most of the time i get CRC errors. Thanks for any help !!! Good as TDK discs are for most, they may be a poor match for your drive. If the manufacturer recommends a line of media, try some of that type. Note that it is extremely unlikely that discs rated 48x will write well at 4x. The most likely optimum speed (fewest errors) may be 16x. Mike -- http://www.mrichter.com/ |
#2
|
|||
|
|||
Mike Richter wrote in message ...
Hi, I have a LiteOn 48x and I have problems with TDK disc also. I just don't use em anymore. Craig George R. wrote: Hi, before i start here my config: WinXP Sp1, 384 MB Ram, Soyo Dragon+ board, AMD 1900+. I run Prime95 and memtest86 without any problems. My system is stable and kept well and up-to-date. I have one HD on IDE2 (Promise port), the CDRom on (Via) IDE0 and the Burner (Lite-On 52246S, latest firmware 6s0f) on (Via) IDE1. Every drive is on it's own IDE port and jumpered as master. All UDMA is on. I use 80 pin UDMA cables for all my drives. I even double checked and swapped my CDRom with the Burner today to see what happens. I can not burn ONE single error-free CD with this burner, using good TDK brand 48x CD-RWs. I even got down to burning at 4x speed to avoid errors, but still a no-go. Not even at 4x ! I first used Nero 5.5.10.42....now i got Nero 6 - still the same results. If i burn a typical, say ~500MB CD with lots of files i always get two or three files where Nero says "Verify error", the burned files don't match the ones on HD. When i burn a large ~500MB zip archive etc. then also most of the time i get CRC errors. Thanks for any help !!! Good as TDK discs are for most, they may be a poor match for your drive. If the manufacturer recommends a line of media, try some of that type. Note that it is extremely unlikely that discs rated 48x will write well at 4x. The most likely optimum speed (fewest errors) may be 16x. Mike |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
CD Burner burning DVDs..... | Stephan | Homebuilt PC's | 6 | May 5th 05 02:38 AM |
burnin read verify errors - SATA dirve | rello | Homebuilt PC's | 0 | July 5th 04 02:31 PM |
Slowest cd burning speed on dvd burner | Chris | General | 1 | April 3rd 04 01:54 AM |
Can't install any OS (hardware fault?) | Paul Richard | Homebuilt PC's | 4 | September 27th 03 12:55 PM |
Liteon 52x burner only burns at 16x | Ric | Cdr | 10 | July 25th 03 01:49 PM |