|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
April 23rd 04, 02:47 AM
|
|||
|
|||
Networker + direct SAN backup
Hi all!
This is my first post to that group, so I would like to say hallo to everybody. The situation is like this: There a EMC, Server (with Networker 7.1) and a PowerVault 132T. They are connected to Fibre Switch. Is it possible to create client wchich would provide direct backup EMC - PV132? I mean: EMC - PV132 not EMC - Server - PV132. I hope it is clear. How can I create such client? -- Abadonna 
|
|
#2
April 23rd 04, 02:58 AM
|
|||
|
|||
|
On Fri, 23 Apr 2004 11:47:21 +1000, Abadonna
wrote: Hi all! This is my first post to that group, so I would like to say hallo to everybody. The situation is like this: There a EMC, Server (with Networker 7.1) and a PowerVault 132T. They are connected to Fibre Switch. Is it possible to create client wchich would provide direct backup EMC - PV132? I mean: EMC - PV132 not EMC - Server - PV132. I hope it is clear. How can I create such client? not really up on EMC at all but it sounds more like an architectural issue you're dealing with. What I think you're asking for is serverless backup. Not something easy to come by; true serverless backup. Correct me if I'm wrong but you want blocks of data to go from disk directly to tape with no host in the middle? Nothing that I know of does that yet with any reliability. I spoke with a tape vendor a few years ago and they could get the data on tape no problem, getting it back was a real challenge. The problem is no reference. Having said that, if you're only looking for full image restore only (no single file or directory) I believe it's available. you might want to ask your Legato rep if they have it, but I'm pretty sure others do. It may also be hardware vendors that do it rather than software. ~F
|
|
#3
April 23rd 04, 03:39 PM
|
|||
|
|||
|
"Abadonna" wrote in message
.. . Hi all! This is my first post to that group, so I would like to say hallo to everybody. The situation is like this: There a EMC, Server (with Networker 7.1) and a PowerVault 132T. They are connected to Fibre Switch. Is it possible to create client wchich would provide direct backup EMC - PV132? I mean: EMC - PV132 not EMC - Server - PV132. I hope it is clear. How can I create such client? Think you need the NDMP stuff from legato. As the other post says , speak to your legato support/advisor.
|
|
#4
April 26th 04, 04:55 AM
|
|||
|
|||
|
Hi,
If Legato Networker is not a must, then you can ask EMC about EDM SymmPath backup. But you will need another EDM server to handle that and it is not cheap. Abadonna wrote: Hi all! This is my first post to that group, so I would like to say hallo to everybody. The situation is like this: There a EMC, Server (with Networker 7.1) and a PowerVault 132T. They are connected to Fibre Switch. Is it possible to create client wchich would provide direct backup EMC - PV132? I mean: EMC - PV132 not EMC - Server - PV132. I hope it is clear. How can I create such client?
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| pc problems after g card upgrade + sp2 | ben reed | Homebuilt PC's | 9 | November 30th 04 01:04 AM |
| NTI Drive Backup Behavior | Earl F. Parrish | Cdr | 0 | January 13th 04 02:11 AM |
| Networker/NDMP backup problems | Michael Taylor | Storage & Hardrives | 0 | November 5th 03 04:14 PM |
| BackUp MyPC: How to Slow Down the CD Burner? | JamesDad | Cdr | 5 | October 29th 03 04:10 AM |
| Help: Backup Exec 9.0 backup on to Plextor DVD+RW via Roxio | Jeff Ishaq | Cdr | 0 | October 22nd 03 06:39 PM |
Linear Mode
