If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
520BPS problem
Have recently obtained EMC CLARiiON FC (fibre channel) ST336704FCV
drives that are 520BPS formatted. It will not work on linux or win unless it is reformatted to 512 BPS. Is it possible to reformat them to 512BPS ? I use SCU command utility (OS W2003 server, FC HBA Adaptec AFC-9210LPC but, screenshot: scu.exe show inquiry pages Unit Serial Number Page: Page Code: 0x80 Page Length: 20 Product Serial Number: 3CD1A8JE00002123FF0E Implemented Operating Definitions Page: Page Code: 0x81 Page Length: 3 Current Operating Definition: SCSI-3 Default Operating Definition: SCSI-3 (Savable) Supported Operating Definitions: SCSI-3 (Savable) Device Identification Page: Page Code: 0x83 Page Length: 12 Code Set: 0x1 (identifier is binary) Identifier Type: 0x3 Identifier Length: 8 FC-PH Name Identifier: 0x2000002037dd7575 Vendor Specific Page: Page Code: 0xc0 Page Length: 56 Vendor Specific Data: 31 32 30 34 33 41 39 30 "12043A90" 42 38 32 36 42 38 32 36 "B826B826" 30 30 30 31 30 30 30 31 "00010001" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 45 30 31 "00000E01" Vendor Specific Page: Page Code: 0xc1 Page Length: 16 Vendor Specific Data: 20 20 20 20 20 20 20 20 " " 31 32 30 34 32 30 30 30 "12042000" Vendor Specific Page: Page Code: 0xc2 Page Length: 2 Vendor Specific Data: 00 02 " " Vendor Specific Page: Page Code: 0xc3 Page Length: 60 Vendor Specific Data: 03 05 00 53 54 33 33 36 " ST336" 37 30 34 46 43 20 20 20 "704FC " 20 20 20 03 10 00 63 a4 " c " 02 e0 00 06 bc 38 58 10 " 8X " 00 02 c0 10 40 00 00 8c " @ " 1f 02 00 00 02 c0 04 05 " " 00 00 05 05 6c 80 00 1e " l " 00 1e 00 18 " " Vendor Specific Page: Page Code: 0xd1 Page Length: 0 Vendor Specific Data: Vendor Specific Page: Page Code: 0xd2 Page Length: 0 scu.exe show edt bus 5 target 0 lun 0 full Equipment Device Table (EDT) Information: Inquiry Information: SCSI Bus ID: 5 SCSI Target ID: 0 SCSI Target LUN: 0 Attached Devices: PhysicalDrive1 Peripheral Device Type: 0 (Direct Access) Peripheral Qualifier: 0 (Peripheral Device Connected) Device Type Modifier: 0 Removable Media: No ANSI Version: 3 (Complies to ANSI X3.xxx-199x, SCSI- ECMA Version: 0 ISO Version: 0 Response Data Format: 2 (SCSI-2) Normal ACA Support: Yes Terminate I/O Process: No Additional Length: 139 Medium Changer Support: No Multi-port Device Support: Yes Soft Reset Support: No Command Queuing Support: Yes Target Transfer Disable: No Linked Command Support: Yes Synchronous Data Transfers: No Support for 16 Bit Transfers: No Support for 32 Bit Transfers: No Relative Addressing Support: No Vendor Identification: SEAGATE Product Identification: ST336704 CLAR36 Firmware Revision Level: 3A90 Vendor Specific Data: 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 " " scu.exe set device block 512 (waiting cca 3 min.) scu.exe: DeviceIoControl(cmd 0x1a) failed, error = 1117 - The request could not be performed because of an I/O device error. scu.exe: 'mode sense (6)' failed on device 'ST336704 CLAR36' at nexus [5/0/0] scu.exe: [5/0/0] CAM CCB function 'XPT_SCSI_IO' failed, CAM status = CAM_REQ_CMP_ERR (0x4) - CCB request completed with an error any idea !? Mario |
#2
|
|||
|
|||
520BPS problem
wrote in message ups.com... Have recently obtained EMC CLARiiON FC (fibre channel) ST336704FCV drives that are 520BPS formatted. It will not work on linux or win unless it is reformatted to 512 BPS. Is it possible to reformat them to 512BPS ? I use SCU command utility (OS W2003 server, FC HBA Adaptec AFC-9210LPC but, screenshot: scu.exe show inquiry pages Unit Serial Number Page: Page Code: 0x80 Page Length: 20 Product Serial Number: 3CD1A8JE00002123FF0E Implemented Operating Definitions Page: Page Code: 0x81 Page Length: 3 Current Operating Definition: SCSI-3 Default Operating Definition: SCSI-3 (Savable) Supported Operating Definitions: SCSI-3 (Savable) Device Identification Page: Page Code: 0x83 Page Length: 12 Code Set: 0x1 (identifier is binary) Identifier Type: 0x3 Identifier Length: 8 FC-PH Name Identifier: 0x2000002037dd7575 Vendor Specific Page: Page Code: 0xc0 Page Length: 56 Vendor Specific Data: 31 32 30 34 33 41 39 30 "12043A90" 42 38 32 36 42 38 32 36 "B826B826" 30 30 30 31 30 30 30 31 "00010001" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 45 30 31 "00000E01" Vendor Specific Page: Page Code: 0xc1 Page Length: 16 Vendor Specific Data: 20 20 20 20 20 20 20 20 " " 31 32 30 34 32 30 30 30 "12042000" Vendor Specific Page: Page Code: 0xc2 Page Length: 2 Vendor Specific Data: 00 02 " " Vendor Specific Page: Page Code: 0xc3 Page Length: 60 Vendor Specific Data: 03 05 00 53 54 33 33 36 " ST336" 37 30 34 46 43 20 20 20 "704FC " 20 20 20 03 10 00 63 a4 " c " 02 e0 00 06 bc 38 58 10 " 8X " 00 02 c0 10 40 00 00 8c " @ " 1f 02 00 00 02 c0 04 05 " " 00 00 05 05 6c 80 00 1e " l " 00 1e 00 18 " " Vendor Specific Page: Page Code: 0xd1 Page Length: 0 Vendor Specific Data: Vendor Specific Page: Page Code: 0xd2 Page Length: 0 scu.exe show edt bus 5 target 0 lun 0 full Equipment Device Table (EDT) Information: Inquiry Information: SCSI Bus ID: 5 SCSI Target ID: 0 SCSI Target LUN: 0 Attached Devices: PhysicalDrive1 Peripheral Device Type: 0 (Direct Access) Peripheral Qualifier: 0 (Peripheral Device Connected) Device Type Modifier: 0 Removable Media: No ANSI Version: 3 (Complies to ANSI X3.xxx-199x, SCSI- ECMA Version: 0 ISO Version: 0 Response Data Format: 2 (SCSI-2) Normal ACA Support: Yes Terminate I/O Process: No Additional Length: 139 Medium Changer Support: No Multi-port Device Support: Yes Soft Reset Support: No Command Queuing Support: Yes Target Transfer Disable: No Linked Command Support: Yes Synchronous Data Transfers: No Support for 16 Bit Transfers: No Support for 32 Bit Transfers: No Relative Addressing Support: No Vendor Identification: SEAGATE Product Identification: ST336704 CLAR36 Firmware Revision Level: 3A90 Vendor Specific Data: 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 " " scu.exe set device block 512 (waiting cca 3 min.) scu.exe: DeviceIoControl(cmd 0x1a) failed, error = 1117 - The request could not be performed because of an I/O device error. scu.exe: 'mode sense (6)' failed on device 'ST336704 CLAR36' at nexus [5/0/0] scu.exe: [5/0/0] CAM CCB function 'XPT_SCSI_IO' failed, CAM status = CAM_REQ_CMP_ERR (0x4) - CCB request completed with an error any idea !? Mario 520 bytes per sector is what's used in the AS/400 envionment (now called iSeries by IBM). Search google groups (groups.google.com) for utilities that can reconvert these disks. If I remember correctly, not all drives will collaborate. Regards, Alvin. |
#3
|
|||
|
|||
520BPS problem
On 4 ruj, 22:07, "Alvin Andries"
wrote: wrote in message ups.com... Have recently obtained EMC CLARiiON FC (fibre channel) ST336704FCV drives that are 520BPS formatted. It will not work on linux or win unless it is reformatted to 512 BPS. Is it possible to reformat them to 512BPS ? I use SCU command utility (OS W2003 server, FC HBA Adaptec AFC-9210LPC but, screenshot: scu.exe show inquiry pages Unit Serial Number Page: Page Code: 0x80 Page Length: 20 Product Serial Number: 3CD1A8JE00002123FF0E Implemented Operating Definitions Page: Page Code: 0x81 Page Length: 3 Current Operating Definition: SCSI-3 Default Operating Definition: SCSI-3 (Savable) Supported Operating Definitions: SCSI-3 (Savable) Device Identification Page: Page Code: 0x83 Page Length: 12 Code Set: 0x1 (identifier is binary) Identifier Type: 0x3 Identifier Length: 8 FC-PH Name Identifier: 0x2000002037dd7575 Vendor Specific Page: Page Code: 0xc0 Page Length: 56 Vendor Specific Data: 31 32 30 34 33 41 39 30 "12043A90" 42 38 32 36 42 38 32 36 "B826B826" 30 30 30 31 30 30 30 31 "00010001" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 30 30 30 "00000000" 30 30 30 30 30 45 30 31 "00000E01" Vendor Specific Page: Page Code: 0xc1 Page Length: 16 Vendor Specific Data: 20 20 20 20 20 20 20 20 " " 31 32 30 34 32 30 30 30 "12042000" Vendor Specific Page: Page Code: 0xc2 Page Length: 2 Vendor Specific Data: 00 02 " " Vendor Specific Page: Page Code: 0xc3 Page Length: 60 Vendor Specific Data: 03 05 00 53 54 33 33 36 " ST336" 37 30 34 46 43 20 20 20 "704FC " 20 20 20 03 10 00 63 a4 " c " 02 e0 00 06 bc 38 58 10 " 8X " 00 02 c0 10 40 00 00 8c " @ " 1f 02 00 00 02 c0 04 05 " " 00 00 05 05 6c 80 00 1e " l " 00 1e 00 18 " " Vendor Specific Page: Page Code: 0xd1 Page Length: 0 Vendor Specific Data: Vendor Specific Page: Page Code: 0xd2 Page Length: 0 scu.exe show edt bus 5 target 0 lun 0 full Equipment Device Table (EDT) Information: Inquiry Information: SCSI Bus ID: 5 SCSI Target ID: 0 SCSI Target LUN: 0 Attached Devices: PhysicalDrive1 Peripheral Device Type: 0 (Direct Access) Peripheral Qualifier: 0 (Peripheral Device Connected) Device Type Modifier: 0 Removable Media: No ANSI Version: 3 (Complies to ANSI X3.xxx-199x, SCSI- ECMA Version: 0 ISO Version: 0 Response Data Format: 2 (SCSI-2) Normal ACA Support: Yes Terminate I/O Process: No Additional Length: 139 Medium Changer Support: No Multi-port Device Support: Yes Soft Reset Support: No Command Queuing Support: Yes Target Transfer Disable: No Linked Command Support: Yes Synchronous Data Transfers: No Support for 16 Bit Transfers: No Support for 32 Bit Transfers: No Relative Addressing Support: No Vendor Identification: SEAGATE Product Identification: ST336704 CLAR36 Firmware Revision Level: 3A90 Vendor Specific Data: 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 00 00 00 00 " " 00 00 00 00 " " scu.exe set device block 512 (waiting cca 3 min.) scu.exe: DeviceIoControl(cmd 0x1a) failed, error = 1117 - The request could not be performed because of an I/O device error. scu.exe: 'mode sense (6)' failed on device 'ST336704 CLAR36' at nexus [5/0/0] scu.exe: [5/0/0] CAM CCB function 'XPT_SCSI_IO' failed, CAM status = CAM_REQ_CMP_ERR (0x4) - CCB request completed with an error any idea !? Mario 520 bytes per sector is what's used in the AS/400 envionment (now called iSeries by IBM). Search google groups (groups.google.com) for utilities that can reconvert these disks. If I remember correctly, not all drives will collaborate. Regards, Alvin. Alvin, tnx MIGHTY PENGUIN! here it is: http://groups.google.hr/group/comp.p...7baa8d3ee433d0 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problem: GeForce 6600 DDR3, I have a surrounding texture display problem | cellist | Nvidia Videocards | 1 | April 29th 07 04:03 PM |
Problems With Adaptec 2400a RAID Card. (rare problem ? ? ? or Common Problem...? ? ?) | Starz_Kid | General | 0 | December 28th 05 05:36 AM |
Please please please... could someone please help me with my problem, i am really really stuck (Asus eax800xt-2dhtv wdm driver problem, no capture!) | Mads | Ati Videocards | 0 | March 12th 05 07:46 PM |
2nd problem with P4P800-E Deluxe problem -- USB and 3rd IDE visible at boot but gone in Windows | Greg Conquest | Asus Motherboards | 5 | September 27th 04 08:58 AM |
* A7N8X bios/boot problem - Save & Exit death problem ? | Jay Bittle | Asus Motherboards | 1 | January 12th 04 08:16 AM |