If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
CPU Voltage Measurements
What utility/program do you folks use to measure the CPU core voltage?
I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) |
#2
|
|||
|
|||
CPU Voltage Measurements
The E6600 has a feature by which it saves power when idle. It does this in
two ways that I know of: lowering the internal clock multiplier (from x9 to x6) and lowering the requested VCore by about 0.2V. This explains what you read in CPU-Z, unless you specifically disabled the power saving feature in the BIOS. As for the other progs, I don't use them so cannot comment (except for speedfan which I use only to measure temps). "Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) |
#3
|
|||
|
|||
CPU Voltage Measurements
"Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) "M. R. Carleer" wrote in message ... The E6600 has a feature by which it saves power when idle. It does this in two ways that I know of: lowering the internal clock multiplier (from x9 to x6) and lowering the requested VCore by about 0.2V. This explains what you read in CPU-Z, unless you specifically disabled the power saving feature in the BIOS. As for the other progs, I don't use them so cannot comment (except for speedfan which I use only to measure temps). Thanks for your reply. I have all of the power saving features turned off. My guess is the variation is just measurement 'noise', not actual voltage variation. It only occurs during 100% stress tests, not in any static situation. Jack R. |
#4
|
|||
|
|||
CPU Voltage Measurements
Well, in my case, I can tell you that the ~0.1V variation has nothing to do
with noise. It is indeed clearly due to the C2D going into idle power saving mode: - As long as I do nothing with my PC, the voltage is around 1.14 +/- 0.01 V. As soon as I start using the CPU heavily (Orthos or some other intensive prog), the voltage raises to 1.22 +/- 0.01 V. - It happens completely in sync with the clock multiplier going from x 6 to x 9. And back when going back to idle. OK, this is all with an Asus P5W DH mobo. Speedfan gives me the exact same figures. "Jack R" wrote in message ... "Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) "M. R. Carleer" wrote in message ... The E6600 has a feature by which it saves power when idle. It does this in two ways that I know of: lowering the internal clock multiplier (from x9 to x6) and lowering the requested VCore by about 0.2V. This explains what you read in CPU-Z, unless you specifically disabled the power saving feature in the BIOS. As for the other progs, I don't use them so cannot comment (except for speedfan which I use only to measure temps). Thanks for your reply. I have all of the power saving features turned off. My guess is the variation is just measurement 'noise', not actual voltage variation. It only occurs during 100% stress tests, not in any static situation. Jack R. |
#5
|
|||
|
|||
CPU Voltage Measurements
Michel R. Carleer wrote:
Well, in my case, I can tell you that the ~0.1V variation has nothing to do with noise. It is indeed clearly due to the C2D going into idle power saving mode: - As long as I do nothing with my PC, the voltage is around 1.14 +/- 0.01 V. As soon as I start using the CPU heavily (Orthos or some other intensive prog), the voltage raises to 1.22 +/- 0.01 V. - It happens completely in sync with the clock multiplier going from x 6 to x 9. And back when going back to idle. OK, this is all with an Asus P5W DH mobo. Speedfan gives me the exact same figures. There are two major components to voltage variation. 1) Variation due to Speedstep (EIST). OS changes the FID/VID on the fly, based on processor loading. This can be disabled (a couple different ways). 2) Load line variation. Popularly referred to as "droop". The amount of droop is specified in the processor datasheet. There is a min and a max load line for the processor. Removing all the voltage droop, would actually violate the processor spec. A certain amount of droop is normal, and the acceptable range of load lines is documented by Intel. For example, on my processor, I might expect to see the measured voltage drop by 0.15V, if the processor goes from no load to full load. That is perfectly normal and since VID is fixed on my processor (no EIST), the 0.15V change is due to the load line. Each family of processors has its own load line, so the number for Core2 Duo could be a different one. You can see min, max, and nominal load lines, on page 21 here, for Core2. A motherboard is supposed to stay between min and max, when the regulator is designed for Vcore. http://download.intel.com/design/pro...s/31327804.pdf Paul "Jack R" wrote in message ... "Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) "M. R. Carleer" wrote in message ... The E6600 has a feature by which it saves power when idle. It does this in two ways that I know of: lowering the internal clock multiplier (from x9 to x6) and lowering the requested VCore by about 0.2V. This explains what you read in CPU-Z, unless you specifically disabled the power saving feature in the BIOS. As for the other progs, I don't use them so cannot comment (except for speedfan which I use only to measure temps). Thanks for your reply. I have all of the power saving features turned off. My guess is the variation is just measurement 'noise', not actual voltage variation. It only occurs during 100% stress tests, not in any static situation. Jack R. |
#6
|
|||
|
|||
CPU Voltage Measurements
"Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) Am I reading you correctly? You have all the energy saving mods turned off and your voltage goes "UP" when you apply a load to the CPU? I thought it should go down when a load is applied ... my E-6600 always does. I thought that was the v-droop effect. |
#7
|
|||
|
|||
CPU Voltage Measurements
Yeah, going from 1.14 idle to 1.22 under full load seems like a droop to
you? "Paul" wrote in message ... Michel R. Carleer wrote: Well, in my case, I can tell you that the ~0.1V variation has nothing to do with noise. It is indeed clearly due to the C2D going into idle power saving mode: - As long as I do nothing with my PC, the voltage is around 1.14 +/- 0.01 V. As soon as I start using the CPU heavily (Orthos or some other intensive prog), the voltage raises to 1.22 +/- 0.01 V. - It happens completely in sync with the clock multiplier going from x 6 to x 9. And back when going back to idle. OK, this is all with an Asus P5W DH mobo. Speedfan gives me the exact same figures. There are two major components to voltage variation. 1) Variation due to Speedstep (EIST). OS changes the FID/VID on the fly, based on processor loading. This can be disabled (a couple different ways). 2) Load line variation. Popularly referred to as "droop". The amount of droop is specified in the processor datasheet. There is a min and a max load line for the processor. Removing all the voltage droop, would actually violate the processor spec. A certain amount of droop is normal, and the acceptable range of load lines is documented by Intel. For example, on my processor, I might expect to see the measured voltage drop by 0.15V, if the processor goes from no load to full load. That is perfectly normal and since VID is fixed on my processor (no EIST), the 0.15V change is due to the load line. Each family of processors has its own load line, so the number for Core2 Duo could be a different one. You can see min, max, and nominal load lines, on page 21 here, for Core2. A motherboard is supposed to stay between min and max, when the regulator is designed for Vcore. http://download.intel.com/design/pro...s/31327804.pdf Paul "Jack R" wrote in message ... "Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) "M. R. Carleer" wrote in message ... The E6600 has a feature by which it saves power when idle. It does this in two ways that I know of: lowering the internal clock multiplier (from x9 to x6) and lowering the requested VCore by about 0.2V. This explains what you read in CPU-Z, unless you specifically disabled the power saving feature in the BIOS. As for the other progs, I don't use them so cannot comment (except for speedfan which I use only to measure temps). Thanks for your reply. I have all of the power saving features turned off. My guess is the variation is just measurement 'noise', not actual voltage variation. It only occurs during 100% stress tests, not in any static situation. Jack R. |
#8
|
|||
|
|||
CPU Voltage Measurements
"Forrest" wrote in message et... "Jack R" wrote in message ... What utility/program do you folks use to measure the CPU core voltage? I've been trying an assortment and getting varying results, so I don't know what to trust, and which to use as a guide for OC settings. I get: CPU-Z 1.40: 1.213V (under stress testing, jumps to 1.440V and back) CoreTemp 0.95: 1.3250V BIOS: 1.48V PCProbeII, SpeedFan and FreshDiag: 1.52V This is on an ASUS P5N-E SLI mb, with an Intel C2D E6600, set at +.100 in the BIOS. Thanks for help and suggestions, Jack R. (Currently running at 3.3GHZ, mem at 856MHz, video +15% OC) Am I reading you correctly? You have all the energy saving mods turned off and your voltage goes "UP" when you apply a load to the CPU? I thought it should go down when a load is applied ... my E-6600 always does. I thought that was the v-droop effect. You are reading that correctly, but as I said in another reply, I don't trust the higher reading to be accurate, although it might be. Other programs are not showing that variation. But, I still do not know who to believe. Is it running at 1.2, 1.3, 1.4 or 1.5V? Thanks, Jack R. |
#9
|
|||
|
|||
CPU Voltage Measurements
"Michel R. Carleer" wrote in message ... Yeah, going from 1.14 idle to 1.22 under full load seems like a droop to you? No it doesn't seem like a droop to me ..... that's exactly my point ..... It's going up under a load instead of the expected decrease in voltage. |
#10
|
|||
|
|||
CPU Voltage Measurements
Forrest wrote:
"Michel R. Carleer" wrote in message ... Yeah, going from 1.14 idle to 1.22 under full load seems like a droop to you? No it doesn't seem like a droop to me ..... that's exactly my point ..... It's going up under a load instead of the expected decrease in voltage. Ah, the mysteries of computers :-) Maybe it is the "AI Overclocking" profile feature ? One of the reasons I set a lot of stuff on "manual" on my boards, is to avoid exactly this kind of stuff. BIOS designers do all sorts of crazy things behind your back. Paul |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Relationship between AGP voltage setting in system bios and core/memory voltage? | Jack F. Twist | Overclocking | 1 | July 3rd 06 07:41 AM |
Fan Measurements | Bob | Homebuilt PC's | 1 | February 20th 06 06:40 AM |
incorrect temperature measurements... | KILOWATT | General | 8 | October 1st 03 02:49 AM |
incorrect temperature measurements... | KILOWATT | Asus Motherboards | 7 | October 1st 03 02:49 AM |
Which soundcard ? have very low distortions for fft measurements? | Gaetan Mailloux | PC Soundcards | 1 | September 7th 03 02:45 AM |