If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Problem with Lite-On 52246s
This is usually due to burning media too fast, there are very few CDR's that
will burn reliably at 48x-52x. If it's doing this at 40x on TY or RiTEC TG media, it's probably the drive. Have you tried different firmware on the drive? "Brian" wrote in message news I have a problem with the above drive I'm hoping someone has a fix for. Everything I burn fails at 95-98%........ What happens is burnproof kicks in and the drive slows way down, then the disc fails verification. Nero CD speed scan disc shows an unreadable block. I'm using XP home, Nero and Recordnow Max. I've tried CMC, Ritek, Tayo Yuden, Prodisc and Lead Data. At first it only happened at 48 & 52x but now it's doing it at 40x consistantly. I have anti Virus disabled, Auto insert off and disabled native xp burning. No luck.......... ANy ideas before I ship it back ?????? Thanks............. Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) |
#2
|
|||
|
|||
I was hoping I wouldn't have to ship it back. I bought this one at Newegg also. I just got an RMA so I guess I'll send it back........ Yup, Even tried the newest firmware - XSOF......... Same thing............... Last month I exchanged my 52246 I bought in Feb. because of the same problem you are encountering...burn would be fine until the end and the burnproof would kick in. The disc would spin up and down, up and down. Burns that took 2 1/2 minutes were taking 4. When I ran CDspeed the seek times were outrageous...like 650ms. Bought it from newegg.com and they shipped out a brand new one (box, nero cd, cables, blank cdr/cdrw, etc..) as soon as my RMA was received and it is burning flawlessly. I have a problem with the above drive I'm hoping someone has a fix for. Everything I burn fails at 95-98%........ What happens is burnproof kicks in and the drive slows way down, then the disc Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) |
#3
|
|||
|
|||
I'll assume you meant 6S0F. Actually 6S0D is a bit better for burn quality.
You're not by chance over-burning are you? "Brian" wrote in message ... Yup, Even tried the newest firmware - XSOF......... Same thing............... This is usually due to burning media too fast, there are very few CDR's that will burn reliably at 48x-52x. If it's doing this at 40x on TY or RiTEC TG media, it's probably the drive. Have you tried different firmware on the drive? I have a problem with the above drive I'm hoping someone has a fix for. Everything I burn fails at 95-98%........ What happens is burnproof kicks in and the drive slows way down, then the disc Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) |
#4
|
|||
|
|||
On Tue, 1 Jul 2003 17:37:28 -0600, "Dan G" wrote:
I'll assume you meant 6S0F. Actually 6S0D is a bit better for burn quality. Yup.. typo.......... You're not by chance over-burning are you? I have overburned a few meg in the past but no, not now.................. Yup, Even tried the newest firmware - XSOF......... Same thing............... This is usually due to burning media too fast, there are very few CDR's that will burn reliably at 48x-52x. If it's doing this at 40x on TY or RiTEC TG media, it's probably the drive. Have you tried different firmware on the drive? I have a problem with the above drive I'm hoping someone has a fix for. Everything I burn fails at 95-98%........ What happens is burnproof kicks in and the drive slows way down, then the disc Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) |
#5
|
|||
|
|||
Brian wrote in message . ..
On Tue, 1 Jul 2003 17:37:28 -0600, "Dan G" wrote: I'll assume you meant 6S0F. Actually 6S0D is a bit better for burn quality. Yup.. typo.......... You're not by chance over-burning are you? I have overburned a few meg in the past but no, not now.................. Yup, Even tried the newest firmware - XSOF......... Same thing............... This is usually due to burning media too fast, there are very few CDR's that will burn reliably at 48x-52x. If it's doing this at 40x on TY or RiTEC TG media, it's probably the drive. Have you tried different firmware on the drive? I have a problem with the above drive I'm hoping someone has a fix for. Everything I burn fails at 95-98%........ What happens is burnproof kicks in and the drive slows way down, then the disc Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) Brian.......... There is no mix up a sander can't fix up !!! (Al Bundy) I have the same burner which rocks with Hitachi Maxell 48x or Taiyo Yuden 48x media, and burns steady in CAV mode up to 52x plus as the finishing speed. Quality using Scandisk is fine.... would guess its the unit at fault. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Shortcut problem (southbridge burn) | Ian | Homebuilt PC's | 4 | December 14th 04 10:33 PM |
Mouse Problem | Jeff | Homebuilt PC's | 0 | October 1st 04 06:44 AM |
help with possible video card problem diagnostic | mark497 | Homebuilt PC's | 1 | September 16th 04 09:59 AM |
Boot Problem with Win2000 AMD 2500 XP - A-Bit KD7A system | TMgo | Homebuilt PC's | 2 | August 17th 04 10:03 AM |
Restart problem | DJS0302 | Homebuilt PC's | 0 | June 20th 04 07:37 AM |