If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Thermalright SI-97 dimensions
Hi,
I am considering purchasing the Thermalright SI-97, but I have a particularly annoying fan holder behind the CPU socket and am concerned about whther the heatsink will still fit. What is the distance from where the heatpipes are vertical and the area contacting the CPU diode on the Thermalright SI-97? Also, what is the distance from the area contacting the CPU diode to the other side of the heatsink? My mobo is an Asus A7N8X E Deluxe and can probably just about fit this thing, but the dimensions given on the Thermalright site do not help. Any advice would be greatly appreciated (via email or in the NG). Yours, -- Tom Morris http://www.bbcity.co.uk http://www.freethoughtfilter.com |
#2
|
|||
|
|||
On 1 Jan 2005 15:49:04 -0800, "Tom Morris"
wrote: Hi, I am considering purchasing the Thermalright SI-97, but I have a particularly annoying fan holder behind the CPU socket and am concerned about whther the heatsink will still fit. What is the distance from where the heatpipes are vertical and the area contacting the CPU diode on the Thermalright SI-97? Also, what is the distance from the area contacting the CPU diode to the other side of the heatsink? My mobo is an Asus A7N8X E Deluxe and can probably just about fit this thing, but the dimensions given on the Thermalright site do not help. Any advice would be greatly appreciated (via email or in the NG). By "fan holder" i presume you mean the northbridge heatsink. Be glad you have it, that's an almost perfect heatsink for nForce2 as there's no maintenance to it without fan, and thus quiet too. The primary downside is Asus' implementation of it, specifically the mounting via phase-change pad. I have an A7N8X-Dlx and when i removed that 'sink I noticed that the pad never even melted in the center, had never even contacted the center of the northbridge, rather only the edges. Frankly I blame the chip foundary too, by now you'd think they could mould the chips such that they're not concave as it's the worst possible surface for good heat conduction. Anyway, the heatsink will come off. If the SI-97 isn't tall enough you can remove the original NB 'sink and use something else, or cut/grind/etc it down short enough. If you don't care how pretty it looks a pair of tin snips would even do the job. I happen to have a different Asus board (but same NB 'sink) sitting out in front of me right now, on it the top of the NB 'sink sits roughly 31mm above the surface of the board. If you can determine the measurements of the Thermalright 'sink itself you can then do the math to find out if there's sufficient clearance. The base of the CPU heatsink will be about 8mm above the surface of the board so distance from (the plane of the bottom of the SI-97) to (the parallel plane of the bottom of the overhanging portion) would need be = 24mm, leaving 1mm to spare for measurement error. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Thermalright SI-97 dimensions | Tom Morris | General | 1 | January 2nd 05 12:53 AM |
Thermalright xp--120 on prescott 2.8 @ 3.5 | James | Overclocking | 3 | December 9th 04 05:28 AM |
Thermalright SLK-948U Glue Problem | vaguely_annoyed@wasted_time.com | Overclocking | 4 | April 21st 04 04:08 AM |
ThermalRight SP-94 vs. Swiftech MCX478-V | Wayne Youngman | Overclocking | 7 | April 4th 04 10:07 AM |
ThermalRight SLK-900U & Vantec Tornado fan? | callsignviper | Overclocking | 2 | August 26th 03 06:12 PM |