If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Power supply?
I was sittin' my kitchen listening to streaming-audio and all of a sudden I
heard a click and my computer died; not a slow death, but an absolute instant-death! Everything connected to the power supply: fans, case lights, etc., are all dead! Is it safe to assume that the power supply went south? I suppose not, since when I first put it together, nothing would come on because of a bad memory-stick. The power supply is an Antec power supply that came with my Antec case, are these generally good power supplies? There's no user-replaceable fuse, should I look for this in a replacement, if it is indeed the power supply? Thoughts? Thanks in advance! |
#2
|
|||
|
|||
Toxic Sweat wrote:
I was sittin' my kitchen listening to streaming-audio and all of a sudden I heard a click and my computer died; not a slow death, but an absolute instant-death! Everything connected to the power supply: fans, case lights, etc., are all dead! Is it safe to assume that the power supply went south? No. Disconnect items one at a time (starting with drives), and check for PSU operation after each. If the PSU still won't start, test the PSU. To test an ATX PSU: First, disconnect everything from the power supply (including MB.) Plug AC cord into the rear of the PS. IF the PS has its own rocker on/off switch, turn it ON. There should be +5v on pin 9 of the 20 pin connector (+5vsb, usually a violet wire.) There should be 0.8v on pin 14 (PS-ON, usually a green wire.) This is from an internal pull-up to the +5vsb. Connect PS power leads to 1 or 2 IDE HDs (for a load). Jumper pin 14 (PS-ON) to pin 13 (ground, black wire.) At this point, fan in PS should start spinning, drives should spin, and + 5/12v, -5/12v, +3.3v, and +5vsb should be present at 20 pin connector. Disconnecting pin 14-13 jumper should turn supply back off. Further, if the PSU starts: When your system fails to start, what is the voltage on pin 9? If it is less than 4.75v, either a) the logic on your motherboard is shorting b) your +5vsb is under powered, or c) your PS is bad. It is most likely a combination of b) and c). If your +5vsb is OK, measure pin 14 of the PS/MB connector. If it is 0.8v (and the +5vsb is OK), the power supply should be on. If pin 14 is 0.8v, the +5vsb is OK, and the PS is OFF, the PS is bad. If pin 14 is 2.0v, the power supply is being told to stay OFF by the MB. If depressing the front panel ON/OFF switch does NOT lower pin 14 to 0.8v (and the +5vsb is OK), then the problem is NOT the power supply, but rather MB related. |
#3
|
|||
|
|||
Thank you! I will print your reply and do the step by step checks, it
sounds like a hassle, but I suppose there's no other way, unless I just take it somewhere and say: "fix it" Thanks again! Ray |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
my new mobo o/c's great | rockerrock | Overclocking AMD Processors | 9 | June 30th 04 08:17 PM |
help, please, with Compaq Presario power supply problem | Jacques Clouseau | General | 6 | June 9th 04 06:44 PM |
power supply, or ...? | ynotssor | General | 10 | June 1st 04 01:19 AM |
How can I make motherboard to restart after power loss automatically? | Amiran | General | 1 | September 24th 03 11:35 PM |
Power Supply on its way out? | w_tom | General | 5 | July 31st 03 03:43 PM |