![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
Hello all,
searched around for the following problem in Google, yet was not able to find some good answers, so here I am (apologies in advance for the lengthy post). A couple of months ago I bought a brand new P4C800-E motherboard. Flashed the BIOS to the latest version (1.016 IIRC at the time) and then proceeded to tune the BIOS settings. I had (and still have) the following devices: - Maxtor 120Gb SATA hdd installed on the Intel ICH controller - NEC 2500 DVD-R (PATA) installed also as an Ultra-ATA (PATA) device on the same controller. IOW, I did not use the promise controller at all. In the BIOS I configured the IDE settings to use: - Enhanced mode, on - S-ATA - (Intel) RAID disabled - Promise controller fully disabled After that I installed Windows XP Home on the system and have been living happily with it, till the introduction of some demanding applications demanding on disk (plus the XP SP2, what a memory/disk hog). So I was seeking ways to improve my disk transfer. Then I stumbled upon the Intel application accelerator. As a test, I installed version 2.2.2 on my portable computer, to find out that the improvement in disk loading was immense. I wanted the same performance boost on my Asus P4C800 system as well! Alas, the Intel app accel was not available for Intel 875P-based mobos (like the Asus one above). _BUT_ the Intel _RAID_ app accel _was_. Downloaded the thingie and tried to install it in XP. No go. It was complaining about "unsupported platform". A closer look indicated that in order for this to run, an Intel RAID BIOS should be operating. And here is where my trouble starts. Went into BIOS and performed the following changes in IDE config: - Set (Intel) RAID to enabled (from disabled) - Doing so, makes an another option appear "Intel RAID BIOS" (or something like that). Also enabled that one. Tried to reboot. The initial XP boot screen came up and a couple of seconds later the system rebooted for no reason. After some (yet more) searching, I've found that I should possibly _first_ have enabled RAID functionality BEFORE formatting/fdisk'ing the disk and installing Win XP... :/ And something else: according to what I've read (even in the mobo manual), enabling the Intel RAID BIOS, should allow me to press CTRL+I during the bios post, in order to invoke the intel raid bios application. This does not happen!!! Kept pressing CTRL+I yet nothing happened. In any case, I don't have a RAID and definitely won't have one. Just wanted Intel RAID app accel to improve hdd performance (I've seen other systems in a similar setup: Intel RAID BIOS active, intel raid app accel installed and operating, but no raids, only a single disk, with very good hdd performance). My questions (and need all the help I can get here guys): 1) Why doesn't CTRL+I work? Something else I should do in the BIOS or elsewhere? My guess is that I've already prepared the HDD, with the BIOS setting for RAID set to off. Now it is set to on, the Intel BIOS does not see any "RAID-Ready" disks and does not come into play. Ideas? 2) Assuming that I have to reformat the disk and start from scratch here, having the Intel BIOS set to "enable", I wouldn't like to have to start from scratch. I'd like to move my entire XP installation (lotsa files and apps) to the new setup, can't stand to reinstall all these things. So was thinking something like: borrowing a large disk, installing it on the promise controller, using ghost to copy my xp disk to a ghost image on the borrowed disk, set BIOS option for the intel controller to "RAID"+"Enable RAID BIOS", format/fdisk my own disk, ghost restore my data back to my disk. Will it work? Will the system boot allright in this case, or should I expect problems of some sort? If the CTRL+I does work in this case, should I do something in the Intel RAID BIOS application? My specs are , with HT enabled in bios, single 512 DDR mem stick, the two storage devices I mentioned... Once more apologies for this lengthy post, I really don't know what to do :/ Best Regards and thanks in advance, Michail.- |
#2
|
|||
|
|||
![]()
Michail Pappas wrote:
Hello all, searched around for the following problem in Google, yet was not able to find some good answers, so here I am (apologies in advance for the lengthy post). A couple of months ago I bought a brand new P4C800-E motherboard. Flashed the BIOS to the latest version (1.016 IIRC at the time) and then proceeded to tune the BIOS settings. I had (and still have) the following devices: - Maxtor 120Gb SATA hdd installed on the Intel ICH controller - NEC 2500 DVD-R (PATA) installed also as an Ultra-ATA (PATA) device on the same controller. IOW, I did not use the promise controller at all. In the BIOS I configured the IDE settings to use: - Enhanced mode, on - S-ATA - (Intel) RAID disabled - Promise controller fully disabled After that I installed Windows XP Home on the system and have been living happily with it, till the introduction of some demanding applications demanding on disk (plus the XP SP2, what a memory/disk hog). So I was seeking ways to improve my disk transfer. Then I stumbled upon the Intel application accelerator. As a test, I installed version 2.2.2 on my portable computer, to find out that the improvement in disk loading was immense. I wanted the same performance boost on my Asus P4C800 system as well! Alas, the Intel app accel was not available for Intel 875P-based mobos (like the Asus one above). _BUT_ the Intel _RAID_ app accel _was_. Downloaded the thingie and tried to install it in XP. No go. It was complaining about "unsupported platform". A closer look indicated that in order for this to run, an Intel RAID BIOS should be operating. And here is where my trouble starts. Went into BIOS and performed the following changes in IDE config: - Set (Intel) RAID to enabled (from disabled) - Doing so, makes an another option appear "Intel RAID BIOS" (or something like that). Also enabled that one. Tried to reboot. The initial XP boot screen came up and a couple of seconds later the system rebooted for no reason. After some (yet more) searching, I've found that I should possibly _first_ have enabled RAID functionality BEFORE formatting/fdisk'ing the disk and installing Win XP... :/ And something else: according to what I've read (even in the mobo manual), enabling the Intel RAID BIOS, should allow me to press CTRL+I during the bios post, in order to invoke the intel raid bios application. This does not happen!!! Kept pressing CTRL+I yet nothing happened. In any case, I don't have a RAID and definitely won't have one. Just wanted Intel RAID app accel to improve hdd performance (I've seen other systems in a similar setup: Intel RAID BIOS active, intel raid app accel installed and operating, but no raids, only a single disk, with very good hdd performance). My questions (and need all the help I can get here guys): 1) Why doesn't CTRL+I work? Something else I should do in the BIOS or elsewhere? My guess is that I've already prepared the HDD, with the BIOS setting for RAID set to off. Now it is set to on, the Intel BIOS does not see any "RAID-Ready" disks and does not come into play. Ideas? 2) Assuming that I have to reformat the disk and start from scratch here, having the Intel BIOS set to "enable", I wouldn't like to have to start from scratch. I'd like to move my entire XP installation (lotsa files and apps) to the new setup, can't stand to reinstall all these things. So was thinking something like: borrowing a large disk, installing it on the promise controller, using ghost to copy my xp disk to a ghost image on the borrowed disk, set BIOS option for the intel controller to "RAID"+"Enable RAID BIOS", format/fdisk my own disk, ghost restore my data back to my disk. Will it work? Will the system boot allright in this case, or should I expect problems of some sort? If the CTRL+I does work in this case, should I do something in the Intel RAID BIOS application? My specs are , with HT enabled in bios, single 512 DDR mem stick, the two storage devices I mentioned... Once more apologies for this lengthy post, I really don't know what to do :/ Best Regards and thanks in advance, Michail.- IAA is for raid systems, you'll need a raid setup to install it. I suspect the same is true for the Intel raid bios, it needs to detect a raid setup to run. |
#3
|
|||
|
|||
![]() "Michail Pappas" wrote in message ... Hello all, searched around for the following problem in Google, yet was not able to find some good answers, so here I am (apologies in advance for the lengthy post). A couple of months ago I bought a brand new P4C800-E motherboard. Flashed the BIOS to the latest version (1.016 IIRC at the time) and then proceeded to tune the BIOS settings. I had (and still have) the following devices: - Maxtor 120Gb SATA hdd installed on the Intel ICH controller - NEC 2500 DVD-R (PATA) installed also as an Ultra-ATA (PATA) device on the same controller. IOW, I did not use the promise controller at all. In the BIOS I configured the IDE settings to use: - Enhanced mode, on - S-ATA - (Intel) RAID disabled - Promise controller fully disabled After that I installed Windows XP Home on the system and have been living happily with it, till the introduction of some demanding applications demanding on disk (plus the XP SP2, what a memory/disk hog). So I was seeking ways to improve my disk transfer. Then I stumbled upon the Intel application accelerator. As a test, I installed version 2.2.2 on my portable computer, to find out that the improvement in disk loading was immense. I wanted the same performance boost on my Asus P4C800 system as well! Alas, the Intel app accel was not available for Intel 875P-based mobos (like the Asus one above). _BUT_ the Intel _RAID_ app accel _was_. Downloaded the thingie and tried to install it in XP. No go. It was complaining about "unsupported platform". A closer look indicated that in order for this to run, an Intel RAID BIOS should be operating. And here is where my trouble starts. Went into BIOS and performed the following changes in IDE config: - Set (Intel) RAID to enabled (from disabled) - Doing so, makes an another option appear "Intel RAID BIOS" (or something like that). Also enabled that one. Tried to reboot. The initial XP boot screen came up and a couple of seconds later the system rebooted for no reason. After some (yet more) searching, I've found that I should possibly _first_ have enabled RAID functionality BEFORE formatting/fdisk'ing the disk and installing Win XP... :/ And something else: according to what I've read (even in the mobo manual), enabling the Intel RAID BIOS, should allow me to press CTRL+I during the bios post, in order to invoke the intel raid bios application. This does not happen!!! Kept pressing CTRL+I yet nothing happened. In any case, I don't have a RAID and definitely won't have one. Just wanted Intel RAID app accel to improve hdd performance (I've seen other systems in a similar setup: Intel RAID BIOS active, intel raid app accel installed and operating, but no raids, only a single disk, with very good hdd performance). My questions (and need all the help I can get here guys): 1) Why doesn't CTRL+I work? Something else I should do in the BIOS or elsewhere? My guess is that I've already prepared the HDD, with the BIOS setting for RAID set to off. Now it is set to on, the Intel BIOS does not see any "RAID-Ready" disks and does not come into play. Ideas? 2) Assuming that I have to reformat the disk and start from scratch here, having the Intel BIOS set to "enable", I wouldn't like to have to start from scratch. I'd like to move my entire XP installation (lotsa files and apps) to the new setup, can't stand to reinstall all these things. So was thinking something like: borrowing a large disk, installing it on the promise controller, using ghost to copy my xp disk to a ghost image on the borrowed disk, set BIOS option for the intel controller to "RAID"+"Enable RAID BIOS", format/fdisk my own disk, ghost restore my data back to my disk. Will it work? Will the system boot allright in this case, or should I expect problems of some sort? If the CTRL+I does work in this case, should I do something in the Intel RAID BIOS application? My specs are , with HT enabled in bios, single 512 DDR mem stick, the two storage devices I mentioned... Once more apologies for this lengthy post, I really don't know what to do :/ Best Regards and thanks in advance, Michail.- Did you install windows raid controller drivers BEFORE swithing to raid in bios? Fisshead |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
IDE RAID | Ted Dawson | Asus Motherboards | 29 | September 21st 04 03:39 AM |
Need help with SATA RAID 1 failure on A7N8X Delux | Cameron | Asus Motherboards | 10 | September 6th 04 11:50 PM |
Asus P4C800 Deluxe ATA SATA and RAID Promise FastTrack 378 Drivers and more. | Julian | Asus Motherboards | 2 | August 11th 04 12:43 PM |
Getting a weird Promise RAID (Win XP) error with my ASUS P4C800 Deluxe | M. B. | Asus Motherboards | 5 | February 9th 04 01:19 AM |
DAW & Windows XP RAID Tips, ProTools error -9086 | Giganews | Asus Motherboards | 0 | October 24th 03 06:45 AM |