If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Aeroflow TMD vibration
Just installed a Vantec Aeroflow on my P4 3G system, I've managed to
bring the temps down to 36 C idle 49 C on load .. These figures I like, but The TMD fan on the HS vibrates terribly is this normal, When its running at a low speed all is well, but if I increase the CPU's load and the fan ups its speed the vibration and resulting noice came be heard all over the house. To limit its vibration I've wedged a piece of polystyrene between the fan an the underside casing of the PSU. Is the vibration normal or is there a problem with the fan. As any other Aeroflow uses had this problem. Tony |
#2
|
|||
|
|||
"Tony Ramsden" wrote in message ... Just installed a Vantec Aeroflow on my P4 3G system, I've managed to bring the temps down to 36 C idle 49 C on load .. These figures I like, but The TMD fan on the HS vibrates terribly is this normal, When its running at a low speed all is well, but if I increase the CPU's load and the fan ups its speed the vibration and resulting noice came be heard all over the house. To limit its vibration I've wedged a piece of polystyrene between the fan an the underside casing of the PSU. Is the vibration normal or is there a problem with the fan. As any other Aeroflow uses had this problem. Not here. You sure you have it mounted properly? The spring is tough to latch, but once it's on there it seems very secure. The only problems I've heard with the TMD fans is that some older versions suffered early failure because the frames were screwed on so tight they shorted some of the coils on the perimeter of the fan. YS Tech, which makes the TMD fans and sells them to cooler makers, including Vantec, blamed improper installation. Mine is less than three months old. It runs at full speed all the time, and is no noisier than the stock Intel hsf. As you say, it does a great job of cooling. If the noise is bad and it is indeed the fan, you can either swap it for another or do what I've heard a couple of others try -- use an adapter (search www.directron.com for fan adapter) to mount an 80 mm fan. |
#3
|
|||
|
|||
If I replace the fan won't this affect the efficiency of the unit, I
thought that the TMD fans were used because if its ability to direct the air flow down the centre of the HS. I cannot live with this noise so any suggestions are wellcome. I have a Vantec Stealth SF8025L spare should I use this fan as a replacement? On Thu, 09 Oct 2003 14:01:07 GMT, "Skid" wrote: "Tony Ramsden" wrote in message .. . Just installed a Vantec Aeroflow on my P4 3G system, I've managed to bring the temps down to 36 C idle 49 C on load .. These figures I like, but The TMD fan on the HS vibrates terribly is this normal, When its running at a low speed all is well, but if I increase the CPU's load and the fan ups its speed the vibration and resulting noice came be heard all over the house. To limit its vibration I've wedged a piece of polystyrene between the fan an the underside casing of the PSU. Is the vibration normal or is there a problem with the fan. As any other Aeroflow uses had this problem. Not here. You sure you have it mounted properly? The spring is tough to latch, but once it's on there it seems very secure. The only problems I've heard with the TMD fans is that some older versions suffered early failure because the frames were screwed on so tight they shorted some of the coils on the perimeter of the fan. YS Tech, which makes the TMD fans and sells them to cooler makers, including Vantec, blamed improper installation. Mine is less than three months old. It runs at full speed all the time, and is no noisier than the stock Intel hsf. As you say, it does a great job of cooling. If the noise is bad and it is indeed the fan, you can either swap it for another or do what I've heard a couple of others try -- use an adapter (search www.directron.com for fan adapter) to mount an 80 mm fan. |
#4
|
|||
|
|||
"Tony Ramsden" wrote in message ... If I replace the fan won't this affect the efficiency of the unit, I thought that the TMD fans were used because if its ability to direct the air flow down the centre of the HS. I cannot live with this noise so any suggestions are wellcome. I have a Vantec Stealth SF8025L spare should I use this fan as a replacement? I'm not familiar with that fan, though the Stealth line gets good reviews. As far as the airflow, you're right about the TMD design. But if you look at the adapters, they funnel the air from an 80mm (or bigger) fan into a 60 mm opening, which should cancel out any concerns about dead spots in the center. I'm still happy with my TMD, but if it ever causes problems I'd go with a bigger fan and an adapter. There are cheaper ones out there, I linked Directron because I knew they had several choices. |
#5
|
|||
|
|||
"Tony Ramsden" wrote in message ... Just installed a Vantec Aeroflow on my P4 3G system, I've managed to bring the temps down to 36 C idle 49 C on load .. These figures I like, but The TMD fan on the HS vibrates terribly is this normal, When its running at a low speed all is well, but if I increase the CPU's load and the fan ups its speed the vibration and resulting noice came be heard all over the house. To limit its vibration I've wedged a piece of polystyrene between the fan an the underside casing of the PSU. Is the vibration normal or is there a problem with the fan. As any other Aeroflow uses had this problem. Tony I have the same HSF and there is a vibration with the fan, but it is not making any noise. Perhaps that particular fan has a problem; it shouldn't vibrate to the point of being noisy. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Q: 3200XP and Vantec Aeroflow | Eyman | Overclocking AMD Processors | 3 | February 3rd 04 04:19 PM |
Vantec AeroFlow, is it ok to run it fromthe Mianboard powerwise,and not the PSU ? | We Live For The One We Die For The One | Overclocking | 2 | August 28th 03 09:52 AM |
Vantec Aeroflow, TT TR2-M1, TT TR2-M2 compared. | Wes Newell | Overclocking AMD Processors | 10 | August 25th 03 02:55 PM |
Vantec AeroFlow fan as a case fan good idea ?? | We Live For The One We Die For The One | Overclocking | 0 | August 17th 03 02:30 AM |