If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Noisy N9600GT videocard
The cooling fan of the MSI N9600GT PCI Express 16x graphics card 512MB
Bios 62.94.3C.00.00 on a computer with an MSI P45 Neo3-FR MS-7514 Bios 1.9 PCB 1.0 4GB RAM and Intel Core Quad Q9400 causes a disturbing noise. This is only when showing Bios setup, starting the computer or running Dos from a floppy (backup) and caused by the display adapter cooling fan running at a very high speed. As soon as Windows XP Home SP3 starts the noise disappears (driver?) and PC-Wizard 2008 reports the fan running at 35% at GPU temperature 42C. Can anything be done to cause the adapter fan to run at a much lower (default) speed? TIA |
#2
|
|||
|
|||
Noisy N9600GT videocard
'Eric P.' wrote:
The cooling fan of the MSI N9600GT PCI Express 16x graphics card 512MB Bios 62.94.3C.00.00 on a computer with an MSI P45 Neo3-FR MS-7514 Bios 1.9 PCB 1.0 4GB RAM and Intel Core Quad Q9400 causes a disturbing noise. This is only when showing Bios setup, starting the computer or running Dos from a floppy (backup) and caused by the display adapter cooling fan running at a very high speed. As soon as Windows XP Home SP3 starts the noise disappears (driver?) and PC-Wizard 2008 reports the fan running at 35% at GPU temperature 42C. Can anything be done to cause the adapter fan to run at a much lower (default) speed? _____ According to your post, the graphics adapter cooling fan runs at full speed only when Windows XP is not controlling the system; that means the graphics adapter is NOT LOADED and thus cannot control the fan speed. When you boot from a DOS floppy then DOS is operating system and the graphics adapter driver is NOT LOADED. When you first turn your system on, the BIOS is controlling the system and the graphics adapter driver is NOT LOADED. So the only noise problem you have is for the few seconds or few minutes when your first start your system as 'First of One' posted. I'd suggest you not fool with flashing your graphics BIOS for such a small problem. If you just can't live with the initial noise, an easy solution is to make a change to "Power Options" in (if necessary) and use 'Sleep' rather than 'Shut Down' when you quit Windows XP. This will save the machine state to the hard drive before turning off power. When you turn the system back on, Windows XP will not need to be restarted. All applets and applications that were active when 'Sleep' was selected will be loaded and in their previous state. If you also set the system BIOS to "Quick Boot", then the graphics adapter cooling fan will run at full speed for only a few seconds before the nVidia driver takes control. Or you could just move your system case further from your ear, better sound-proof your system case, or disconnect the graphics card fan power and take a chance - probably with less chance of a disastrous outcome than if you were to edit the graphics adapter BIOS. If the above doesn't help, then consider posting how you use your system. Phil Weldon "Eric P." wrote in message ... The cooling fan of the MSI N9600GT PCI Express 16x graphics card 512MB Bios 62.94.3C.00.00 on a computer with an MSI P45 Neo3-FR MS-7514 Bios 1.9 PCB 1.0 4GB RAM and Intel Core Quad Q9400 causes a disturbing noise. This is only when showing Bios setup, starting the computer or running Dos from a floppy (backup) and caused by the display adapter cooling fan running at a very high speed. As soon as Windows XP Home SP3 starts the noise disappears (driver?) and PC-Wizard 2008 reports the fan running at 35% at GPU temperature 42C. Can anything be done to cause the adapter fan to run at a much lower (default) speed? TIA |
#3
|
|||
|
|||
Noisy N9600GT videocard
Phil Weldon wrote:
'Eric P.' wrote: The cooling fan of the MSI N9600GT PCI Express 16x graphics card 512MB Bios 62.94.3C.00.00 on a computer with an MSI P45 Neo3-FR MS-7514 Bios 1.9 PCB 1.0 4GB RAM and Intel Core Quad Q9400 causes a disturbing noise. This is only when showing Bios setup, starting the computer or running Dos from a floppy (backup) and caused by the display adapter cooling fan running at a very high speed. As soon as Windows XP Home SP3 starts the noise disappears (driver?) and PC-Wizard 2008 reports the fan running at 35% at GPU temperature 42C. Can anything be done to cause the adapter fan to run at a much lower (default) speed? _____ According to your post, the graphics adapter cooling fan runs at full speed only when Windows XP is not controlling the system; that means the graphics adapter is NOT LOADED and thus cannot control the fan speed. When you boot from a DOS floppy then DOS is operating system and the graphics adapter driver is NOT LOADED. When you first turn your system on, the BIOS is controlling the system and the graphics adapter driver is NOT LOADED. So the only noise problem you have is for the few seconds or few minutes when your first start your system as 'First of One' posted. I'd suggest you not fool with flashing your graphics BIOS for such a small problem. If you just can't live with the initial noise, an easy solution is to make a change to "Power Options" in (if necessary) and use 'Sleep' rather than 'Shut Down' when you quit Windows XP. This will save the machine state to the hard drive before turning off power. When you turn the system back on, Windows XP will not need to be restarted. All applets and applications that were active when 'Sleep' was selected will be loaded and in their previous state. If you also set the system BIOS to "Quick Boot", then the graphics adapter cooling fan will run at full speed for only a few seconds before the nVidia driver takes control. Or you could just move your system case further from your ear, better sound-proof your system case, or disconnect the graphics card fan power and take a chance - probably with less chance of a disastrous outcome than if you were to edit the graphics adapter BIOS. If the above doesn't help, then consider posting how you use your system. Phil Weldon Thank you for the comment and advise. Apart from starting up etc I clone (HDCLONE started from a flop) the whole harddisk to other harddisks of the same type at regular intervals as backup which takes about half an hour. I knew ofcourse that running without the windows driver is the reason the cooling fan runs at default speed. But I hate the not needed noise and I think it should have been avoided. I have modified plenty PC Bios'ses in the past starting from the PC AT 80286 period and a few times also a video Bios. I disassembled a lot of Bios code. So I have some knowledge about the innerworkings. I'm not afraid to take a risk, its just hardware after all. All the seven computers I presently have run the latest available Bios. I was really looking for an advise like the one I got from First of One because I know from the past all tools to do the job exist. I'm only hesitating because I would have to study and think about the downloaded stuff before using it and have become a bit lazy lately because of old age (74). In addition it's a bit warm and I have to work in the garden. Thank you again for your time and advise. |
#4
|
|||
|
|||
Noisy N9600GT videocard
'Eric P.' wrote:
Thank you for the comment and advise. Apart from starting up etc I clone (HDCLONE started from a flop) the whole hard disk to other hard disks of the same type at regular intervals as backup which takes about half an hour. I knew ofcourse that running without the windows driver is the reason the cooling fan runs at default speed. But I hate the not needed noise and I think it should have been avoided. I have modified plenty PC Bios'ses in the past starting from the PC AT 80286 period and a few times also a video Bios. I disassembled a lot of Bios code. So I have some knowledge about the innerworkings. I'm not afraid to take a risk, its just hardware after all. All the seven computers I presently have run the latest available Bios. I was really looking for an advise like the one I got from First of One because I know from the past all tools to do the job exist. I'm only hesitating because I would have to study and think about the downloaded stuff before using it and have become a bit lazy lately because of old age (74). In addition it's a bit warm and I have to work in the garden. Thank you again for your time and advise. _____ Well, if your normal tasks don't load the GPU heavily, then try inserting a resistor in the GPU heatsink fan power line (or a rheostat if you want to experiment) to limit the fan speed. It will never run a full speed, but that shouldn't be a problem if the GPU is never heavily loaded.or you could use a Zener diode and a suitable resistor to limit the fan to, say, 35% under all conditions. And even use an external switch to choose a 35% limit for start-up and DOS operation, but flipping the switch for Windows XP operation to allow the nVidia driver to run the GPU fan at any speed, depending on GPU temperature. I happen to use a rheostat controlled fan to cool my hard drives (a 120 mm fan fills the front part of four half height 5 1/4" bays) with the rheostat mounted in an unused bay on a snap-in cover panel (the case has nine 5 1/4 front accessible bays.) I'd bet that at your location you might get away with just limiting the fan to 35% all the time, consider your ambient temperatures have go to be a lot better than the 95 F ( 35 C ) I must contend with in Atlanta and South Florida during the summer. Phil Weldon "Eric P." wrote in message ... Phil Weldon wrote: 'Eric P.' wrote: The cooling fan of the MSI N9600GT PCI Express 16x graphics card 512MB Bios 62.94.3C.00.00 on a computer with an MSI P45 Neo3-FR MS-7514 Bios 1.9 PCB 1.0 4GB RAM and Intel Core Quad Q9400 causes a disturbing noise. This is only when showing Bios setup, starting the computer or running Dos from a floppy (backup) and caused by the display adapter cooling fan running at a very high speed. As soon as Windows XP Home SP3 starts the noise disappears (driver?) and PC-Wizard 2008 reports the fan running at 35% at GPU temperature 42C. Can anything be done to cause the adapter fan to run at a much lower (default) speed? _____ According to your post, the graphics adapter cooling fan runs at full speed only when Windows XP is not controlling the system; that means the graphics adapter is NOT LOADED and thus cannot control the fan speed. When you boot from a DOS floppy then DOS is operating system and the graphics adapter driver is NOT LOADED. When you first turn your system on, the BIOS is controlling the system and the graphics adapter driver is NOT LOADED. So the only noise problem you have is for the few seconds or few minutes when your first start your system as 'First of One' posted. I'd suggest you not fool with flashing your graphics BIOS for such a small problem. If you just can't live with the initial noise, an easy solution is to make a change to "Power Options" in (if necessary) and use 'Sleep' rather than 'Shut Down' when you quit Windows XP. This will save the machine state to the hard drive before turning off power. When you turn the system back on, Windows XP will not need to be restarted. All applets and applications that were active when 'Sleep' was selected will be loaded and in their previous state. If you also set the system BIOS to "Quick Boot", then the graphics adapter cooling fan will run at full speed for only a few seconds before the nVidia driver takes control. Or you could just move your system case further from your ear, better sound-proof your system case, or disconnect the graphics card fan power and take a chance - probably with less chance of a disastrous outcome than if you were to edit the graphics adapter BIOS. If the above doesn't help, then consider posting how you use your system. Phil Weldon Thank you for the comment and advise. Apart from starting up etc I clone (HDCLONE started from a flop) the whole harddisk to other harddisks of the same type at regular intervals as backup which takes about half an hour. I knew ofcourse that running without the windows driver is the reason the cooling fan runs at default speed. But I hate the not needed noise and I think it should have been avoided. I have modified plenty PC Bios'ses in the past starting from the PC AT 80286 period and a few times also a video Bios. I disassembled a lot of Bios code. So I have some knowledge about the innerworkings. I'm not afraid to take a risk, its just hardware after all. All the seven computers I presently have run the latest available Bios. I was really looking for an advise like the one I got from First of One because I know from the past all tools to do the job exist. I'm only hesitating because I would have to study and think about the downloaded stuff before using it and have become a bit lazy lately because of old age (74). In addition it's a bit warm and I have to work in the garden. Thank you again for your time and advise. |
#5
|
|||
|
|||
Noisy N9600GT videocard
Phil Weldon wrote:
Well, if your normal tasks don't load the GPU heavily, then try inserting a resistor in the GPU heatsink fan power line (or a rheostat if you want to experiment) to limit the fan speed. It will never run a full speed, but that shouldn't be a problem if the GPU is never heavily loaded.or you could use a Zener diode and a suitable resistor to limit the fan to, say, 35% under all conditions. And even use an external switch to choose a 35% limit for start-up and DOS operation, but flipping the switch for Windows XP operation to allow the nVidia driver to run the GPU fan at any speed, depending on GPU temperature. I happen to use a rheostat controlled fan to cool my hard drives (a 120 mm fan fills the front part of four half height 5 1/4" bays) with the rheostat mounted in an unused bay on a snap-in cover panel (the case has nine 5 1/4 front accessible bays.) I'd bet that at your location you might get away with just limiting the fan to 35% all the time, consider your ambient temperatures have go to be a lot better than the 95 F ( 35 C ) I must contend with in Atlanta and South Florida during the summer. Phil Weldon I think changing the bios of the N9600GT is a much cleaner solution. Just limit the RPM of the fan when the card is in basic text mode. But I have to find how to do that exactly! In The Netherlands we have sometimes temperatures like that too. On the 19th of july 2006 35.7C was reached in the center of the country. In my small computer room the maximum is often higher in summertime. Thanks again for the info |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Noisy N9699GT videocard | Eric P.[_4_] | Nvidia Videocards | 2 | July 12th 09 03:13 PM |
Videocard MCE? | Paul | Ati Videocards | 1 | September 2nd 05 12:21 AM |
Best videocard | 0ne_Up | Overclocking | 2 | July 5th 04 09:48 PM |
New videocard | Ken | Matrox Videocards | 6 | July 1st 04 10:38 AM |
which videocard | IanJill | Homebuilt PC's | 2 | December 6th 03 11:59 PM |